Description : On the recommendations of Nagpur Conference, the minimum width of a village road may be (A) 2.45 m (B) 2.75 m (C) 3.66 m (D) 4.90 m
Last Answer : Answer: Option A
Description : The normal road land width for a major district road in open area, is (A) 45 m (B) 25 m (C) 15 m (D) 12 m
Last Answer : Answer: Option B
Description : The normal road width of National and State highways (A) Is kept 45 m (B) In plain and rolling terrain built-up area, is 30 m (C) In mountainous built-up area is 20 m (D) All the above
Last Answer : Answer: Option D
Description : The normal road land width for a National or State highway, in open areas should be (A) 45 m (B) 30 m (C) 24 m (D) 20 m
Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s
Last Answer : (B) 16 mm/s
Description : Roadway width for a National highways and State highways (two-lanes) is (A) 12 m (B) 9 m (C) 9.5 m (D) 15 m
Description : The aggregates required for one kilometre length of water bound macadam road per meter width and for 10 mm thickness is (A) 8 cubic meter (B) 10 cubic meter (C) 12 cubic meter (D) 15 cubic meter
Last Answer : Answer: Option C
Description : If the number of lanes on the carriageway of a road is more than two, the total width of lane ways is equal to 3.0 m (A) + 0.60 m (B) + 0.70 m (C) + 0.90 m (D) + 1.50 m
Description : Normal formation width of a hill road for one-way traffic, is (A) 3.6 m (B) 4.8 m (C) 6.6 m (D) 7.2 m
Description : Road width 8.8 m of two lane National highways or State highways in mountainous terrain (A) Excludes the width of parapet (0.6 m) (B) Excludes the width of side drain (0.6 m) (C) Excludes the width of parapet and side drain (D) Includes the width of parapet and side drain
Description : According to IRC : 52-1973, for a single lane National Highway in hilly region, (A) Width of the carriageway must be 3.75 m (B) Shoulders on either side must be 1.25 m (C) Total width of the road-way must be 6.25 m (D) Total of the above
Description : According to Indian Road Congress, the width of carriageway, is (A) 3.75 m for single lane (B) 7.0 m for two lanes without raised kerbs (C) 7.5 m for two lanes with raised kerbs (D) All the above
Description : The minimum width of a septic tank is taken (A) 70 cm (B) 75 cm (C) 80 cm (D) 90 c
Last Answer : (B) 75 cm
Description : The minimum diameter of longitudinal steel should be [ A ] 10 mm [ B ] 12 mm [ C ] 16 mm [ D ] 20 mm
Last Answer : [ B ] 12 mm
Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16
Description : If longitudinally spanning stairs are casted along with their landings, the maximum bending moment per metre width, is taken as (A) wl²/4 (B) wl²/8 (C) wl²/10 (D) wl²/12
Description : The minimum width of the pavement of a National Highway should be (A) 4.7 m (B) 5.7 m (C) 6.7 m (D) 7.7 m
Description : Pick up the correct statement from the following: (A) Minimum desirable width of medians on rural highways is 5 metres (B) Minimum width of medians should be 3 metres (C) On long bridges and viaducts, the width of medians should be 1.5 m (D) All the above
Description : Minimum width of ship clearance shall be (A) B or 30 m (B) 1.5 B or 50 m (C) 1.5 B (D) 50 m
Last Answer : (A) B or 30 m
Description : Pick up the correct statement from the following: (A) The height of head light above road surface, is taken as 0.75 m (B) The beam of head light is up to one degree upwards from the grade of road (C) While designing the valley curve, the height of the object is assumed nil (D) All the above
Description : According to the recommendations of Nagpur Conference, the width formation of an ideal National Highway in hard rock cutting, is (A) 8.9 m (B) 7.9 m (C) 6.9 m (D) 6.5 m
Description : Minimum stopping distance for moving vehicles on road with a design speed of 80 km/hour, is (A) 80 m (B) 100 m (C) 120 m (D) 150 m
Description : The minimum vertical clearance of overhanging cliffs or any other structure above the surface of a hill road, should be (A) 3 m (B) 4 m (C) 5 m (D) 6 m
Description : An intermediate T-beam reinforced with two layers of tensile steel with clear cover 13 cm encasted with the floor of a hall 12 metres by 7 metres, is spaced at 3 metres from adjoining beams and if the width of the beam is ... breadth of the flange is (A) 300 cm (B) 233 cm (C) 176 cm (D) 236 cm
Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm
Description : The pavement width of a road depends upon (A) Terrain (B) Type of traffic (C) Number of lanes (D) All the above
Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t
Description : The width formation of a road means the width of (A) Carriageway (B) Pavement and shoulders (C) Embankment at ground level (D) Embankment at the top level
Description : The width of road pavements, depends upon (A) Width of traffic lane (B) Number of traffic (C) Width of median strip (D) All the above
Description : Width of a rotary round should be equal to (A) Twice the width of narrowest radial road (B) Width of the widest road (C) Width of the widest road plus the width of one lane (D) Width of the widest road plus 2 metres
Description : The width of the right of way, is influenced by (A) Formation width (B) Shoulders or berms (C) Classification of road (D) All the above
Description : The width of different roads as recommended in Nagpur plan by the Indian Road Conference for hilly region, is (A) Same for National Highways (B) Different for National Highways (C) Same for State Highways (D) Same for Major District roads
Description : Formation width of a hill road is the distance between (A) Outer end of side drain to outer end of parapet wall (B) Outer end of side drain to inner end of parapet wall (C) Inner end of side drain to outer end of parapet wall (D) Inner end of side drain to inner end of parapet wall
Description : The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage ... 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these
Last Answer : (B) (6 + 12) chains
Description : Pipes P, Q and R which fill the tank together in 12 hours are opened for 2hours after which pipe R was closed. Find the number of hours taken by pipe R to fill the tank if the remaining tank is filled in 14 hours. A) 16 B) 14 C) 20 D) 42
Last Answer : D 1/P + 1/Q + 1/R = 1/12 Now given that first all open for 2hours, then R closed and P+Q completes in 14 hours, so (1/P + 1/Q + 1/R) *2 + (1/P + 1/Q)*14 = 1 Put 1/P + 1/Q = 1/12 – 1/R (1/12 – 1/R + 1/R) *2 + (1/12 – 1/R)*14 = 1 1/6+ 14/12 – 14/R = 1 Solve, R = 42
Description : The virtual address generated by a CPU is 32 bits. The Translation Lookaside Buffer (TLB) can hold total 64 page table entries and a 4-way set associative (i.e. with 4- cache lines in the set). The page size is 4 KB. The minimum size of TLB tag is (A) 12 bits (B) 15 bits (C) 16 bits (D) 20 bits
Last Answer : (C) 16 bits Explanation: VirtualAddress = 32 bits PageSize = 4KB = 12 bits therefore : VPNTag = 20 bits, OffsetTag = 12 bits TLBEntryLength = VPNTag = 20 bits TotalTLBEntries = 64, 4-way implies ... therefore : TLBIndex = 4 bits TLBTag = TLBEntryLength - TLBIndex = 20 - 4 = 16 bits
Description : End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar
Last Answer : [ A ] Effective depth or 12 times the diameter of bar
Description : In a demand paging memory system, page table is held in registers. The time taken to service a page fault is 8 m.sec. if an empty frame is available or if the replaced page is not modified, and it takes 20 m.secs., if the replaced ... ? (A) 11.6 m.sec. (B) 16.4 m.sec. (C) 28 m.sec. (D) 14 m.sec.
Last Answer : (B) 16.4 m.sec.
Description : The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm
Description : To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these
Description : The minimum design speed for hairpin bends in hill roads is taken as (A) 20 kmph (B) 30 kmph (C) 40 kmph (D) 50 kmph
Description : The Width of a processor’s data path is measured in bits. Which of the following are common data paths? A) 8 bits B) 12 bits C) 16 bits D) 32 bits
Last Answer : Answer : A
Description : The Width of a processor’s data path is measured in bits. Which of the following are common data paths? a. 8 bits b. 12 bits c. 16 bits d. 32 bits
Last Answer : a. 8 bits
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm