Description : __________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning
Last Answer : (C) Strain ageing
Description : Strain hardening effect in metals subjected to cold working is due to the __________ mechanism. (A) Slip (B) Fracture (C) Winning (D) Dislocation
Last Answer : (D) Dislocation
Description : Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism. (A) Fracture (B) Dislocation (C) Slip (D) Twinning
Last Answer : (C) Slip
Description : Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening
Last Answer : Option B
Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface
Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut
Description : cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25
Last Answer : Option C
Description : Metal Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less
Last Answer : ANSWER: C
Description : Steel is more elastic than rubber because _____. A. Its density is high B. It is a metal C. Ratio of stress to strain is more D. Ratio of stress to strain is less
Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure fails (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal strain Theory (c) Thirdly Maximum Principal Energy Theory (d) None
Last Answer : (c) Thirdly Maximum Principal Energy Theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None
Last Answer : (c) Thirdly Maximum Principal stress theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None
Last Answer : (d) None
Description : Total strain energy theory for the failure of a material at elastic limit, is known (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (D) Haig's theory
Description : Shear strain energy theory for the failure of a material at elastic limit, is due to (A) Rankine (B) Guest or Trecas (C) St. Venant (D) Von Mises
Last Answer : (D) Von Mises
Description : Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy
Last Answer : (D) Low stacking fault energy
Description : When a wire is stretched to double in length, the longitudinal strain produced in it is (a) 0.5 (b) 1.0 (c) 1.5 (d) 2.0
Last Answer : b) 1.0
Description : An elastic behaviour of materials is expressed in terms of (A) Hysteresis loop area (B) Stress-strain curve (C) Relaxation time
Last Answer : (C) Relaxation time
Description : All materials obey Hooke's law within elastic limit. When elastic limit is reached, the tensile strain (A) Increases very quickly (B) Decreases very quickly (C) Increases in proportion to stress (D) Decreases in proportion to stress
Last Answer : (A) Increases very quickly
Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C
Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these
Last Answer : (A) Applies to elastic deformation
Description : The elastic strain in copper is due to the (A) Motion of dislocations (B) Stretching of atomic bonds (C) Breakage of atomic bonds (D) None of the above
Last Answer : Option A
Description : Resilience of spring is (a) Strain energy per unit length (b) Strain energy per unit area (c) Strain energy per unit mass (d) None
Description : As the elastic limit reaches, tensile strain (A) Increases more rapidly (B) Decreases more rapidly (C) Increases in proportion to the stress (D) Decreases in proportion to the stress
Last Answer : (A) Increases more rapidly
Description : What is the maximum value of deforming force upto which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (3) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : What is the maximum value of deforming force up to which a material shows elastic property and above which the material loses it? (1) Elasticity (2) Strain (3) Elastic Limit (4) Stress
Last Answer : (4) Elastic Limit Explanation: The Maximum Extent to which a solid may be stretched without permanent alteration of size or shape.
Description : The elastic stress strain behavior of rubber is A. Linear B. Nonlinear C. Plastic D. No fixed relationship
Last Answer : B. Nonlinear
Description : The ratio of shear stress and shear strain of an elastic material, is (A) Modulus of Rigidity (B) Shear Modulus (C) Modulus of Elasticity (D) Both (a) and (b)
Last Answer : (D) Both (a) and (b)
Description : Maximum strain theory for the failure of a material at the elastic limit, is known as (A) Guest's or Trecas' theory (B) St. Venant's theory (C) Rankine's theory (D) Haig's theory
Last Answer : (B) St. Venant's theory
Description : The law which states, "Within elastic limits strain produced is proportional to the stress producing it", is known as (A) Bernoulli's law (B) Stress law (C) Hooke's law (D) Poisson's law
Last Answer : (C) Hooke's law
Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above
Last Answer : (D) All the above
Description : Creep coefficient is the ratio of [ A ] Ultimate Creep strain to elastic strain [ B ] Elastic strain to ultimate Creep strain [ C ] Elastic strain to plastic strain [ D ] Plastic strain to elastic strain
Last Answer : [ A ] Ultimate Creep strain to elastic strain
Description : The statement : stress is proportional to strain, i.e. the Hooke’s law holds good upto (a) Elastic Limit (b) Proportional Limit (c) Plastic Limit (d) Yield point
Last Answer : (b) Proportional Limit
Description : The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable
Last Answer : (B) Less
Description : A concentric double pipe heat exchanger as compared to the shell and tube heat exchanger for the same heat load requires (A) Less heating surface (B) More space (C) Lower maintenance cost (D) None of these
Last Answer : (B) More space
Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity
Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer coefficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s
Description : As compared to uniaxial tension or compression, the strain energy stored in bending is only (A) 1/8 (B) 1/4 (C) 1/3 (D) 1/2
Last Answer : (C) 1/3
Description : Which of the following phenomenon/ phenomena is/are diffusion controlled? (A) Dislocation climb (B) Cross-slip (C) Twinning (D) Recrystallisation
Last Answer : (D) Recrystallisation
Description : The hardenability of steel decreases with (A) Decrease in dislocation density (B) Increase in solutionising temperature (C) Increase in strength (D) Decrease in grain size
Last Answer : D) Decrease in grain size
Description : With increase in annealing temperature, the following defect density decreases. (A) Vacancy (B) Dislocation (C) Grain boundary (D) All of these
Last Answer : Option D
Description : The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these
Last Answer : (a) Strain
Description : The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material. (A) Elastic (B) Ultimate (C) Yielding (D) Breaking
Last Answer : (C) Yielding
Description : Metal (M) crystallizes in a cubic unit cell with density 3.2 g/cc. Edge-length of the unit cell is `4.37Å` picometre (pm) The number of nearest neighb
Last Answer : Metal (M) crystallizes in a cubic unit cell with density 3.2 g/cc. Edge-length of the unit cell is `4.37Å` ... Ca atom are A. 4 B. 6 C. 8 D. 12
Description : Metal (M) crystallizes in a cubic unit cell with density 3.2 g/cc. Edge-length of the unit cell is `4.37Å` picometre (pm) The nearest neighbour will b
Last Answer : Metal (M) crystallizes in a cubic unit cell with density 3.2 g/cc. Edge-length of the unit ... diagonal C. On the face diagonal D. On opposite face
Description : If edge length of an unit cell `=4xx10^(-8)` cm and the unit cell is a face-centered cubic with atomic mass of metal is 40 then density of the unit ce
Last Answer : If edge length of an unit cell `=4xx10^(-8)` cm and the unit cell is a face-centered cubic with atomic mass of ... /(24) `gm/ml D. `(1)/(4)` gm/litre
Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected
Last Answer : (C) Appreciable strain hardening is produced
Description : Pick out the wrong statement. (A) The equivalent stiffness of two springs (of equal stiffness 'S') in series is S/2 while in parallel is 2S (B) For a helical spring, deflection is ... is less than the buckling load (D) Modulus of resilience is proportional to (stress at elastic limit)2
Last Answer : (C) Crushing load or columns is less than the buckling load
Description : Rittinger number which designates the new surface produced per unit of mechanical energy absorbed by the material being crushed, depends on the (A) State or manner of application of the crushing force (B) Ultimate strength of the material (C) Elastic constant of the material (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : If price of coffee falls leading to increase in total outlay on coffee, the demand of coffee is (a) Elastic ; (b) Inelastic ; (c) Unitary elastic ; (d) Less than unit elastic
Last Answer : (a) Elastic ;
Description : If price of X falls leading to fall in total outlay on X, the demand of X is (a) Elastic ; (b) Inelastic ; (c) Unitary elastic ; (d) Less than unit elastic
Last Answer : (b) Inelastic ;
Description : If price of X falls leading to increase in total outlay on X, the demand of X is (a) Elastic ; (b) Inelastic ; (c) Unitary elastic ; (d) Less than unit elastic