Description : Strain hardening effect in metals subjected to cold working is due to the __________ mechanism. (A) Slip (B) Fracture (C) Winning (D) Dislocation
Last Answer : (D) Dislocation
Description : __________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning
Last Answer : (C) Strain ageing
Description : Which of the following phenomenon/ phenomena is/are diffusion controlled? (A) Dislocation climb (B) Cross-slip (C) Twinning (D) Recrystallisation
Last Answer : (D) Recrystallisation
Description : Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy
Last Answer : (D) Low stacking fault energy
Description : Between 230 and 370°C, blue brittleness is caused in mild steel because of the (A) Immobility of dislocation (B) Strain-ageing (C) Increase in Young's modulus (D) Strain hardening
Last Answer : Option B
Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected
Last Answer : (C) Appreciable strain hardening is produced
Description : The increase in hardness of metal due to its cold working is termed as the __________ hardening. (A) Work (B) Age (C) Induction (D) Flame
Last Answer : (A) Work
Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation
Last Answer : b) Plasticity
Description : Repeated Ankle dislocation for 1 month with no Fracture, what to do?
Last Answer : answer:If the joint is dislocating it is also damaging, stretching the tendons, ligaments, hence the repetitive nature of the injury. I had to have a pin pput in my shoulder for the same reason, ... your dancing, excercising. etc right now. I'd get to an orthopedist and have the situation assessed.
Description : To counteract the bad effects of strain hardening on a cold formed part, it must be (A) Tempered (B) Normalised (C) Annealed (D) Hardened
Last Answer : Option C
Description : Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening
Last Answer : (C) Annealing
Description : Pick out the wrong statement about the machinability of metals. Machinability of a metal (A) Decreases with increase in strain hardening tendencies (B) Decreases with increase in hardness, in general (C) Depend on the composition, microstructure and physical & mechanical
Description : 9. The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is (A) More (B) Equal (C) Less (D) Double
Last Answer : Option A
Description : Cold working of a material results in increase in hardness, which is termed as the __________ hardening. (A) Cold (B) Work (C) Age (D) Induction
Last Answer : (B) Work
Description : Pick out the wrong statement. (A) Lead can creep under its own weight at room temperature (B) The electrical conductivity of gold is considerably reduced by alloying additions due to ... metal (D) With increase in temperature, the electrical conductivity of intrinsic semi-conductor will increase
Last Answer : (C) Recrystallisation temperature decreases with decrease in strain in a cold worked metal
Description : Pick out the wrong statement. (A) Both annealing and normalising release the internal stresses of the material besides improving the mechanical properties (B) Low carbon steel does not respond to ... are also used for surface hardening (D) Martempering of a material is a hardening process
Description : The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the (A) Work hardening (B) Bauschinger effect (C) Creeping effect (D) Stress recovery effect
Last Answer : (B) Bauschinger effect
Description : Due to constant use both inlet and exhaust valves and their seats subjected to a) stress wear b) strain wear c) mechanical wear d) tensile wear
Last Answer : c) mechanical wear
Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out
Last Answer : (a) stick-slip
Description : Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out
Last Answer : a) Stick-slip
Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality
Description : When mild steel is subjected to a tensile load, its fracture will conform to (a) Star shape (b) Granular shape (c) Cup and cone shape (d) Fibrous shape
Last Answer : (c) Cup and cone shape
Description : To improve the machinability of steel by its softening, it is subjected to (A) Cold working (B) Annealing (C) Shot blasting (D) Heating
Last Answer : (B) Annealing
Description : cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is (A) 0 (B) 0.33 (C) 0.44 (D) 0.25
Description : Pick out the wrong statement. (A) Cold cracking of a weld is due to the presence of hydrogen gas in the weld (B) True stress is given by, σ = σE (1 + εE), where σE and εE ... in the iron blast furnace (D) High residual stress at the surface is beneficial for fatigue properties of a material
Description : Wrought metal is to be, A. Marble B. Quenched C. Subjected /undergone/ to cold treatment during processing (annealed)
Last Answer : C. Subjected /undergone/ to cold treatment during processing (annealed)
Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working
Description : When a thin plate is subjected to loading in its own plane only, the condition is called _ a.plane stress b.plane strain c.zero stress d.zero strain
Last Answer : a.plane stress
Description : When a gas or a liquid is subjected to an increased pressure, the substance contracts, the bulk strain is defined as A. final volume ⁄ original volume B. final pressure ⁄ original pressure C. change in volume ⁄ original volume D. original volume ⁄ change in volume
Last Answer : change in volume ⁄ original volume
Description : The total strain energy for a unit cube subjected to three principal stresses is given by? a) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/3 b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ c) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/4 d) None of the mentioned
Last Answer : b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE
Last Answer : (D) W²L/2AE
Description : The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called (A) Stiffness (B) Proof resilience (C) Proof stress (D) Proof load
Last Answer : (B) Proof resilience
Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these
Last Answer : (A) Zero
Description : A solid cube is subjected to equal normal forces on all its faces. The volumetric strain will be x- times the linear strain in any of the three axes when (A) x = 1 (B) x = 2 (C) x = 3 (D) x = 4
Last Answer : (C) x = 3
Description : When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these
Last Answer : (b) Directly proportional to
Description : Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) ... its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature
Last Answer : (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal
Description : . Age hardening is connected with (A) Babbitt metal (B) Gun metal (C) Stainless steel (D) Duralumin
Last Answer : D) Duralumin
Description : Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal
Description : The hardenability of steel decreases with (A) Decrease in dislocation density (B) Increase in solutionising temperature (C) Increase in strength (D) Decrease in grain size
Last Answer : D) Decrease in grain size
Description : With increase in annealing temperature, the following defect density decreases. (A) Vacancy (B) Dislocation (C) Grain boundary (D) All of these
Last Answer : Option D
Description : Sub zero treatment of steel is done to (A) Suppress martensite transformation (B) Enhance its working performance in sub zero atmosphere (C) Reduce the retained austenite in hardened steel (D) Induce temper brittleness after its hardening
Description : Secondary hardening in steels arises out of the (A) Precipitation of fine alloy carbides at high temperatures (B) Refinement of ferrite grain size by working (C) Decomposition of retained austenite upon heat treatment (D) Precipitation of complex inter-metallic upon heat treatment
Description : You are the test manager and you are about the start the system testing. The developer team says that due to change in requirements they will be able to deliver the system to you for ... concentrate more on critical functionality testing D. Add more resources so that the slippage should be avoided
Last Answer : B. Extend the testing plan, so that you can accommodate the slip going to occur
Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding
Last Answer : Answer: A
Description : When repairing a fracture of a lower complete denture, which statement is correct: A. Self curing will distort the denture B. Cold curing will not be strong enough because of small area of attachment C. There is a possibility of occlusal disharmony
Last Answer : C. There is a possibility of occlusal disharmony
Description : With high frequency electric current hardening is achieved and is called as a) case hardening b) induction hardeningc) surface hardening d) metal hardening
Last Answer : b) induction hardening
Description : Hardening is a process of heating a metal to a) 400°C b) 500°C c) 600°C d) 700°C
Last Answer : c) 600°C
Description : Hardening of steel is not possible unless it is heated __________ critical point. (A) Above the highest (B) Above the lowest (C) Between the first & second (D) Between the second & third
Last Answer : (B) Above the lowes
Description : __________ is not a case hardening process. (A) Carburising (B) Nitriding (C) Cyaniding (D) Annealing
Last Answer : (D) Annealing