Description : Pick up the incorrect statement from the following: (A) The retaining wall should be structurally capable to resist the applied earth pressure (B) The section of the retaining wall should be so ... off water from the earth retained, weep holes are provided near the top of the retaining wall
Last Answer : Answer: Option D
Description : In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as (A) A key (B) A cut-off wall (C) A rib (D) All the above
Description : A retaining wall 6m high supports a backfill with a surcharge angle of 10°. The back of the wall is inclined to the vertical at a positive batter angle of 5°. If the angle of wall friction is 7°, then the resultant ... inclined to the horizontal at an angle of (A) 7° (B) 10° (C) 12° (D) 17
Last Answer : (C) 12°
Description : For the design of retaining walls, the minimum factor of safety against overturning is taken as (A) 1.5 (B) 2.0 (C) 2.5 (D) 3.0
Last Answer : Answer: Option B
Description : Parapet walls along hill roads, are provided (A) To retain the back filling (B) To prevent the hill from sliding (C) To prevent the wheels of the vehicle from coming on the retaining wall (D) None of these
Last Answer : Answer: Option C
Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)
Description : To have pressure wholly compressive under the base of a retaining wall of width b, the resultant of the weight of the wall and the pressure exerted by the retained, earth should have eccentricity not more than (A) b/3 (B) b/4 (C) b/5 (D) b/6
Description : A failure wedge develops if a retaining wall (A) Moves away from the backfill (B) Moves towards the backfill (C) Sinks downwards (D) Stresses equally by vertical and horizontal forces
Last Answer : Answer: Option A
Description : The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5
Description : he lateral earth pressure on a retaining wall (A) Is equal to mass of the soil retained (B) Proportional to the depth of the soil (C) Proportional to the square of the depth of the soil (D) Proportional to the internal friction of the soil
Last Answer : (D) Proportional to the internal friction of the soil
Description : Pick up the correct definition from the following: (A) The lateral pressure exerted by the soil when the retaining wall moves away from the back fill, is generally known as active earth pressure of the soil (B ... the back fill, is known as 'earth pressure at rest of the soil (D) All the above
Description : If is the angle of repose of soil of weight w kg/m3 , the horizontal pressure p at a depth of h metres per metre length of wall, is (A) wh × [(1 - sin )/(1 + )] (B) (wh/2) × [(1 - sin )/(1 + )] (C) wh - sin )/(1 + )] (D) wh )/(1 - )
Description : The design of a retaining wall assumes that the retained earth (A) Is dry (B) Is free from moisture (C) Is not cohesive (D) All the above
Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these
Description : The walls which are necessary on the hill side of roadway where earth has to be retained from slipping is known as (A) Retaining wall (B) Breast wall (C) Parapet wall (D) None of the above
Description : The design of heel slab of a retaining wall is based on the maximum bending moment due to: (A) Its own weight (B) Weight of the soil above it (C) Load of the surcharge, if any (D) All the above
Description : A wall constructed to resist the pressure of an earth filling, is called (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall
Last Answer : Option A
Description : Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of (A) h/4 (B) h/3 (C) h/2 (D) 2h/3
Description : The dock wall is designed as a gravity retaining wall and is tested for (A) Back fill pressure when the dock is empty (B) Maximum water pressure from the dock without any back fill (C) The load charge ... to the dock by the movement of loaded vehicles or trains on the way (D) All of the above
Last Answer : (D) All of the above
Description : If is the overall height of a retaining wall retaining a surcharge, the width of the base slab usually provided, is (A) 0.3 H (B) 0.4 H (C) 0.5 H (D) 0.7 H
Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above
Description : The work done in sliding a block of weight of 50 kg up a plane inclined at an angle of 30? to the horizontal so that the block is lifted through 1 m ( a.More than 50 kgm b.50 kgm c.Less than 5 kgm d.15 kgm only e.None of the above
Last Answer : a. More than 50 kgm
Description : Rankine's theory of active earth pressure assumes (A) Soil mass is homogeneous, dry and cohesionless (B) Ground surface is a plane which may be horizontal or inclined (C) Back of the wall is vertical and smooth (D) All the above
Description : The major principal stress in an element of cohesion-less soil within the backfill of a retaining wall is (A) Vertical if the soil is in an active state of plastic equilibrium (B) Vertical if the ... state of plastic equilibrium (C) Inclined at 45° to the vertical plane (D) None of the above
Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom
Description : The wall constructed for the stability of an excavated portion of a road on the hill side, is known as (A) Retaining wall (B) Breast wall (C) Parapet wall (D) All the above
Description : The wall constructed for the stability of a back filling portion of a road on the downhill side, is known as (A) Retaining wall (B) Breast wall (C) Parapet wall (D) All the above
Description : Pick up the correct statement from the following: (A) The breakwater which can be used as a platform for loading and unloading of cargo is called a mole (B) The brick masonry retaining wall which is ... wall (C) Three types of break waters are generally provided in harbours (D) All of the above
Description : A T-shaped retaining wall mainly consists of (A) One cantilever (B) Two cantilevers (C) Three cantilevers (D) Four cantilevers
Last Answer : (C) Three cantilevers
Description : The main reinforcement in the toe of a T-shaped R C. retaining wall is provided on (i) Top face parallel to the wall (ii) Top face perpendicular to the wall (iii) Bottom face parallel to the wall (iv) ... (i) and (ii) are correct (C) (iii) and (iv) are correct (D) Only (iv) is correct
Description : The main reinforcement in the heel of a T-shaped R.C. retaining wall is provided on (A) Top face perpendicular to wall (B) Bottom face perpendicular to wall (C) Both top and bottom faces perpendicular to wall (D) None of these
Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)
Description : Which of the following R.C. retaining walls is suitable for heights beyond 6 m? (A) L-shaped wall (B) T-shaped wall (C) Counterfort type (D) All of the above
Description : In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above
Description : In a counterfort retaining wall, the main reinforcement is provided on the (i) Bottom face in front counterfort (ii) Inclined face in front counterfort (iii) Bottom face in back counterfort (iv) Inclined face in back counterfort ... (B) (ii) and (iii) (C) (i) and (iv) (D) (iii) and (iv)
Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face
Description : The stepped structure provided for lateral support of a structure, is (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall
Description : The frame consists of a steel beam welded rigidly to two vertical channels. An eccentric exciter weighing 250 N is attached to the beam, which weighs 10 KN and is used to excite the frame. The unbalance weight of ... ends, magnification factor at resonance is A. 307.5 B. 3.075 C. 30.75 D. 0.3075
Last Answer : C. 30.75
Description : The stability of a dam is checked for (A) Tension at the base (B) Overturning of the wall or dam (C) Sliding of the wall or dam (D) All of these
Description : The pressure drop in a 30 cm diameter horizontal pipe is 60 kPa in distance of 15m. The wall shear stress in kPa is (a) 0.1 (b) 0.2 (c) 0.3 (d) 0.4
Last Answer : (c) 0.3
Description : For an I beam, the shape factor is 1.12. If the allowable stress (with factor of safety in bending as 1.5) is increased by 20% for wind and earthquake loads, the modified load factor is (a) 1.10 (b) 1.25 (c) 1.35 (d) 1.40
Last Answer : (d) 1.40
Description : Partial safety factor for strength in steel m Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65
Last Answer : [ A ] 1.15
Description : Partial safety factor for strength of concrete in Limit state design is [ A ] 1.15 [ B ] 1.25 [ C ] 1.5 [ D ] 1.65
Last Answer : [ C ] 1.5
Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5
Last Answer : (B) 0.1
Description : Weep holes are provided in retaining and breast walls (A) To drain off the water from the filling (B) To ventilate the stone masonry (C) To add architectural beauty (D) To increase compaction of the earth retained
Description : The water pressure per metre length on a vertical masonry wall of dam is (where w = Specific weight of the liquid, and H = Height of the liquid) (A) wH/2 (B) wH (C) wH2 /2 (D) wH2 /4
Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall per unit length is (where w = Specific weight of liquid, and H = Height of liquid) (A) wH (B) wH/2 (C) wH2 /2 (D) wH2 /3
Description : Who would introduce me some academic methods of retaining wall(was dragged by a equipment)?
Last Answer : I just need the method，so the depth of water，the hight of wall, drag force, and so on can be represented by the English alphabets.