Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
(A) Creep
(B) Fatigue
(C) Endurance
(D) Tensile
by

1 Answer

Answer :

(B) Fatigue
by

Related questions

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Last Answer : D) Endurance limit

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Description : Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Last Answer : (C) Creep

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Description : Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Last Answer : Option B

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Description : Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Last Answer : (C) Under stressing the specimen

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Description : Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Last Answer : Option C

Friedrich Wohler prepared the organic compound

Description : Friedrich Wohler prepared the organic compound

Last Answer : urea.

Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Description : Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Last Answer : Option D

Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Last Answer : Option B

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Description : The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Last Answer : (c) Material of the test specimen

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Description : __________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

Last Answer : (B) Shot peening

Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Last Answer : d. Good cast ability

Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Description : Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Last Answer : (a) Ductility

A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Description : A material is capable of resisting softening at high temperature, because of its property termed as (A) Hot temper (B) Hot hardness (C) Fatigue (D) Creep

Last Answer : (B) Hot hardness

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower  than the ultimate stress of the material. This property of metal, is called  (A) Plasticity of the ... ) Elasticity of the metal  (C) Fatigue of the metal  (D) Workability of the metal

Last Answer : (C) Fatigue of the metal

Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Last Answer : (C) Fluctuating

Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating(B) Tensile(C) Compressive(D) Torsion

Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion

Last Answer : (A) Fluctuating

Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Last Answer : Option B

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : B) Completely reversed

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : (B) Completely reversed

Distinguish between creep and fatigue.

Description : Distinguish between creep and fatigue.

Last Answer : Creep is low and progressive deformation of a material with time under a constant stress at high temperature applications. Fatigue is the reduced tendency of material to offer resistance to applied stress under repeated or fluctuating loading condition.

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

Distinguish Between Creep And Fatigue?

Description : Distinguish Between Creep And Fatigue?

Last Answer : Creep is low and progressive deformation of a material with time under a constant stress at high-temperature applications. Fatigue is the reduced tendency of material to offer resistance to applied stress under repeated or fluctuating loading condition.

Explain the laboratory procedure to determine the compressive strength of concrete cubes as per IS-516-1959 with reference to following points: i. Preparation of test specimen ii. Procedure of testing iii. Interpretation of results

Description : Explain the laboratory procedure to determine the compressive strength of concrete cubes as per IS-516-1959 with reference to following points: i. Preparation of test specimen ii. Procedure of testing iii. Interpretation of results

Last Answer : Preparation of test specimen: i. Take three cubes of 15 cm sides and apply oil to its inner surface. ii. Prepare the concrete mixture of required grade and fill it in each mould in 3 layers. ... say 23N/mm 2) than the specified grade M20, then that concrete is safe and good for construction.

What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Description : What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Last Answer : ANSWER: Y -- YIELD STRENGTH

Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its fatigue strength (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Description : Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its ... (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Last Answer : (C) Cold working of a metal decreases its fatigue strength

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

. __________ test can be termed as the semi-destructive test. (A) Impact (B) Torsion (C) Hardness (D) Charpy

Description : . __________ test can be termed as the semi-destructive test. (A) Impact (B) Torsion (C) Hardness (D) Charpy

Last Answer : Option C

The first organic compound synthesized in 1828 by Frederich Wohler was: w) benzene x) urea y) estrogen z) methane

Description : The first organic compound synthesized in 1828 by Frederich Wohler was: w) benzene x) urea y) estrogen z) methane

Last Answer : ANSWER: X -- UREA

Amino resins are used in paper treatment to improve its (A) Wet tear and bursting strength (B) Folding endurance (C) Wet rub resistance(D) All (A), (B) & (C)

Description : Amino resins are used in paper treatment to improve its (A) Wet tear and bursting strength (B) Folding endurance (C) Wet rub resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Lead alone is not used in storing equipment, because it (A) Is very costly (B) Corrodes easily (C) Is having low creep strength (D) None of these

Description : Lead alone is not used in storing equipment, because it (A) Is very costly (B) Corrodes easily (C) Is having low creep strength (D) None of these

Last Answer : (C) Is having low creep strength

The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the (A) Work hardening (B) Bauschinger effect (C) Creeping effect (D) Stress recovery effect

Description : The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the (A) Work hardening (B) Bauschinger effect (C) Creeping effect (D) Stress recovery effect

Last Answer : (B) Bauschinger effect