Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit
Last Answer : (D) Endurance limit
Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point
Last Answer : (c) endurance limit to the working stress
Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these
Last Answer : (B) Endurance limit
Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65
Last Answer : (c) 0.50
Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (a)Firstly Ultimate >yield > elastic limit
Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (c) Thirdly Ultimate=yield=elastic limit
Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength
Last Answer : Option A
Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion
Last Answer : (b) Pitting
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load
Last Answer : (d) completely reversed load
Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength
Last Answer : (A) Modulus of elasticity (young's modulus)
Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point
Last Answer : (d) below the yield point
Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above
Last Answer : b. Soderberg line
Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength
Last Answer : b) Yield strength
Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit
Last Answer : D) Endurance limit
Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength
Last Answer : (D) Elastic limit close to ultimate breaking strength
Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength
Last Answer : (D) Its elastic limit very close to ultimate breaking strength
Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)
Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength
Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded
Last Answer : E. Elastic limit was exceeded
Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion
Last Answer : (D) Thermal co-efficient of expansion
Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile
Last Answer : (B) Fatigue
Description : Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)? (A) E = 2G (1 + v) (B) E = G (1 + v) (C) E = G (1 + v)/2 (D) E = 2G (1 + 2v)
Last Answer : (A) E = 2G (1 + v)
Description : The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress
Last Answer : (B) Conformability
Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress
Last Answer : (A) Embeddability
Description : spring material should have low (A) Elastic limit (B) Deflection value (C) Fatigue resistance (D) None of these
Last Answer : Option D
Description : The most important property for the spring material is (a) High elastic limit (b) High deflection value (c) Resistance to fatigue and shock (d) All of these
Last Answer : (d) All of these
Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance
Last Answer : (A) Impact strength
Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)
Last Answer : (C) Creep resistance
Last Answer : (D) All (A), (B) & (C)
Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these
Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the ... ) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal
Last Answer : (C) Fatigue of the metal
Description : Young's modulus is defined as A. tensile strain/tensile stress B. tensile stress/tensile strain C. tensile stress × tensile strain D. length/area
Last Answer : tensile stress/tensile strain
Description : Ratio of tensile to strain is A. Young's modulus B. stress C. stiffness D. tensile force
Last Answer : Young's modulus
Description : Young’s Modulus of elasticity is (a)Tensile stress / Tensile strain (b)Shear stress / Shear strain (c)Tensile stress / Shear strain (d)Shear stress / Tensile strain
Last Answer : a)Tensile stress / Tensile strain
Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)
Last Answer : (A) Approaches yield point
Description : The ratio of endurance limit in shear to the endurance limit in flexure is (a) 0.25 (b) 0.40 (c) 0.55 (d) 0.70
Last Answer : (c) 0.55
Description : Shot blasting process improves the endurance limit of the component. a) True b) False
Last Answer : a) True
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile
Description : Theories of elastic failure is the (a) Firstly analysis of the various failures (b) Secondly analysis of the strength of a material (c) Both (a) & (b) (d) None
Last Answer : (c) Both (a) & (b)
Description : Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength
Last Answer : (a)Elastic limit
Description : Theories of elastic failure while dealing with brittle materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None
Last Answer : (a) Ultimate stress
Description : Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None
Last Answer : (b) Yield stress
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping
Last Answer : (a) Fatigue Failure
Description : Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails (A) Below the yield point (B) Above the yield point (C) Below the elastic limit (D) At the elastic limit
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : b) 2
Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue
Last Answer : (B) Toughnes
Description : The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)
Last Answer : B. Percent elongation
Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above
Last Answer : a. Ferrous materials