The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the

lining is called

(A) Embeddability

(B) Conformability

(C) Viscosity

(D) Endurance limit stress
by

1 Answer

Answer :

(A) Embeddability
by

Related questions

The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (B) Conformability

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Last Answer : b) Corrosive

High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Description : High endurance limit of carburised machine parts is because of the fact that carburisation (A) Suppresses any stress concentration produced in the parts (B) Enhances the yield point of the material (C) Introduces a compressive layer on the surface (D) Produces a better surface finish

Last Answer : (C) Introduces a compressive layer on the surface

The ratio of endurance limit in shear to the endurance limit in flexure is (a) 0.25 (b) 0.40 (c) 0.55 (d) 0.70

Description : The ratio of endurance limit in shear to the endurance limit in flexure is (a) 0.25 (b) 0.40 (c) 0.55 (d) 0.70

Last Answer : (c) 0.55

Shot blasting process improves the endurance limit of the component. a) True b) False

Description : Shot blasting process improves the endurance limit of the component. a) True b) False

Last Answer : a) True

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Last Answer : D) Endurance limit

Satisfactory hydrodynamic film in a journal bearing is formed when (a) Journal speed is low; unit pressure on the bearing is high and viscosity of lubricant used is low [IES-2006] (b) Journal speed is low; unit pressure on the bearing is low and viscosity of lubricant used is low (c) Journal speed is high; unit pressure on the bearing is high and viscosity of lubricant used is high (d) Appropriate combination of journal speed, unit pressure on bearing and lubricant viscosity exists resulting in low coefficient of friction

Description : Satisfactory hydrodynamic film in a journal bearing is formed when (a) Journal speed is low; unit pressure on the bearing is high and viscosity of lubricant used is low [IES-2006] ... journal speed, unit pressure on bearing and lubricant viscosity exists resulting in low coefficient of friction

Last Answer : (c) Journal speed is high; unit pressure on the bearing is high and viscosity of lubricant used is high

The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Description : The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Last Answer : (d) viscosity, speed and bearing pressure.

Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. Proportional to the speed of rotation 4. Independent of the pressure Which of the statements given above are correct? (a) 1, 2, 3 and 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Description : Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. ... 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Last Answer : (a) 1, 2, 3 and 4

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only

Which one of the following is correct? [IES-2008] A hydrodynamic slider bearing develops load bearing capacity mainly because of- (a) Slider velocity (b) wedge shaped oil film (c) Oil compressibility (d) oil viscosity

Description : Which one of the following is correct? [IES-2008] A hydrodynamic slider bearing develops load bearing capacity mainly because of- (a) Slider velocity (b) wedge shaped oil film (c) Oil compressibility (d) oil viscosity

Last Answer : (b) wedge shaped oil film

If μ = absolute viscosity, N= speed of the journal and p = unit bearing pressure, then the bearing characteristic number is given by (A) μN/p (B) μp/N (C) pN/μ (D) μ/pN

Description : If μ = absolute viscosity, N= speed of the journal and p = unit bearing pressure, then the bearing characteristic number is given by (A) μN/p (B) μp/N (C) pN/μ (D) μ/pN

Last Answer : (A) μN/p

The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Description : The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Last Answer : (d) all of the mentioned

What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Description : What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Last Answer : a) Adhesive wear

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Last Answer : b) 2

Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None

Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None

Last Answer : (c) Thirdly Maximum Principal stress theory

Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Last Answer : (d) None

The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Description : The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Last Answer : (b) No, it has point contact and hence low rigidity

Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Description : Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Last Answer : b) No it has point contact and hence low rigidity

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength of the insulation B. the paint dust is composed of abrasive and semi-conducting materials which impair insulation C. paint dust buildup has a tendency to cause corrosion D. phase windings frequently become isolated from each other due to dust interference at the terminals

Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals

Last Answer : Answer: B

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (a)Firstly Ultimate >yield > elastic limit

In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (c) Thirdly Ultimate=yield=elastic limit

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Last Answer : a) Elastically

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Description : Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Last Answer : d) Each of the mentioned

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Last Answer : (c) Both (a) & (b)

-The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Last Answer : (A) shot peening