__________ the exhaust gas is an indication of the incomplete combustion of fuel. (A) Low temperature of (B) High temperature of (C) High % of CO in (D) High % of CO2in

__________ the exhaust gas is an indication of the incomplete combustion of fuel.
(A) Low temperature of
(B) High temperature of
(C) High % of CO in
(D) High % of CO2in
by

1 Answer

Answer :

(C) High % of CO in
by

Related questions

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Description : Incomplete combustion of fuel in the furnace is judged by high __________ of the flue gases. (A) CO content (B) Dew point (C) CO2 content (D) O2 content

Last Answer : (A) CO content

Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Description : Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Last Answer : (D) Carbon monoxide

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 %

Description : The heat exhaust of an automobile with an internal combustion engine represents approximately what percent of the energy of the original fuel? w) 10 % x) 50 % y) 35 % z) 5 % 

Last Answer : ANSWER: Y -- 35 % 

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Description : Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Last Answer : (B) % of O2 in

If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Description : If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Last Answer : (B) Dry gas/stack gas loss

When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Description : When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Last Answer : (B) CO

Fuel combustion is never cent per cent efficient due to (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) All (A), (B) and (C)

Description : Fuel combustion is never cent per cent efficient due to (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Description : Based on the exhaust gas analysis, a controller maintains stoichiometric combustion __ a. by commanding a servo motor to adjust the combustion air damper b. By commanding servo motor to adjust the fuel supply valve. c. Both a. & b. d. None of the above.

Last Answer : c. Both a. & b.

Which of the following accounts for maximum energy loss in a boiler? (A) Flue gases (B) Ash content in the fuel (C) Incomplete combustion (D) Unburnt carbon in flue gases

Description : Which of the following accounts for maximum energy loss in a boiler? (A) Flue gases (B) Ash content in the fuel (C) Incomplete combustion (D) Unburnt carbon in flue gases

Last Answer : (A) Flue gases

The reason for excessive clinker formation in gas producers is the (A) Use of coal/coke containing a high % of fines and ash (B) Use of fuel having too low an ash fusion temperature (C) Development of hot spots in the fuel bed and an abnormally high rate of gasification (D) All (A), (B) and (C)

Description : The reason for excessive clinker formation in gas producers is the (A) Use of coal/coke containing a high % of fines and ash (B) Use of fuel having too low an ash fusion temperature (C) Development of hot spots in the fuel bed and an abnormally high rate of gasification (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

Which of the following gases is produced due to incomplete combustion of fuel? (1) Carbon Dioxide (2) Carbon Monoxide (3) Methane (4) Ethane

Description : Which of the following gases is produced due to incomplete combustion of fuel? (1) Carbon Dioxide (2) Carbon Monoxide (3) Methane (4) Ethane

Last Answer : (2) Carbon Monoxide Explanation: Carbon monoxide (CO) is an odorless, colorless gas formed by the incomplete com bustion of fuels. It is produced from the partial oxidation of carbon-containing com pounds; it forms when there is not enough oxygen to produce carbon dioxide.

The engine produces dark black smoke due to a) Burning of oil b) Due of incomplete combustion c) Due to moisture in fuel d) None of these Ans. b

Description : The engine produces dark black smoke due to a) Burning of oil b) Due of incomplete combustion c) Due to moisture in fuel d) None of these Ans. b

Last Answer : ans b

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Description : Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Steam is intermittently admitted into the fuel bed during the production of producer gas to (A) Convert CO to CO2 (B) Increase the combustion rate (C) Increase the gas production rate (D) Minimise the chances of clinker formation

Description : Steam is intermittently admitted into the fuel bed during the production of producer gas to (A) Convert CO to CO2 (B) Increase the combustion rate (C) Increase the gas production rate (D) Minimise the chances of clinker formation

Last Answer : (D) Minimise the chances of clinker formation

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Automobile exhaust is passed through two compartments catalytic converter employing platinum as catalyst for (A) Conversion of CO into CO2 in the second compartment (B) Conversion of NOx into N2 and NH3 in the first compartment (C) Oxidation of unburnt hydrocarbon fuel in the second compartment (D) All (A), (B) and (C)

Description : Automobile exhaust is passed through two compartments catalytic converter employing platinum as catalyst for (A) Conversion of CO into CO2 in the second compartment (B) Conversion of NOx into N2 and NH3 in the first ... of unburnt hydrocarbon fuel in the second compartment (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The progressive warming up of the earth's surface is mainly due to the (A) Automobile exhau(B) Blanketing effect of CO2in the atmosphere(C) De-forestation(D) Thickening of ozone layer

Description : The progressive warming up of the earth's surface is mainly due to the (A) Automobile exhau (B) Blanketing effect of CO2 in the atmosphere (C) De-forestation (D) Thickening of ozone layer

Last Answer : (B) Blanketing effect of CO2 in the atmosphere

If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Description : If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Last Answer : (A) Low(A) Low

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Identify the correct statement with respect to Biogas. (1) Mixture of gases from volcanoes (2) Gas produced from certain crude oil wells (3) Gas produced by incomplete combustion of biomass (4) Gas produced by fermentertian of biomass

Description : Identify the correct statement with respect to Biogas. (1) Mixture of gases from volcanoes (2) Gas produced from certain crude oil wells (3) Gas produced by incomplete combustion of biomass (4) Gas produced by fermentertian of biomass

Last Answer : (4) Gas produced by fermentertian of biomass Explanation: Biogas is produced by the anaerobic digestion or fermentation of biodegradable materials such as biomass, manure, sewage, municipal waste, green waste ... (CO2) and may have small amounts of hydrogen sulphide (H2S), moisture and siloxanes.

Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Description : Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal  gas (c) excess release of carbon monoxide by incomplete  combustion (d) excess formation of CO2 by combustion and  animal respiration.

Last Answer : (a) excess NO2 and SO2 from burning fossil fuels

Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Description : Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Last Answer : (a) excess NO2 and SO2 from burning fossil fuels

_______ is highly poisonous gas produced as a result of incomplete combustion. a) oxygen b)carbon dioxide c)carbon mono oxide d)soot

Description : _______ is highly poisonous gas produced as a result of incomplete combustion. a) oxygen b)carbon dioxide c)carbon mono oxide d)soot

Last Answer : c)carbon mono oxide

Identify the correct stateme-nt with respect to Biogas. (1) Mixture of gases from volcanoes (2) Gas produced from certain crude oil wells (3) Gas produced by incomplete combustion of biomass (4) Gas produced by fermen-tation of biomass

Description : Identify the correct stateme-nt with respect to Biogas. (1) Mixture of gases from volcanoes (2) Gas produced from certain crude oil wells (3) Gas produced by incomplete combustion of biomass (4) Gas produced by fermen-tation of biomass

Last Answer : Gas produced by fermen-tation of biomass

The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: c Explanation: The air flow sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel while exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : In _____________ sensor, output voltage changes in proportion to air-fuel ratio. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: b Explanation: Only in exhaust gas sensor, output voltage changes in proportion to air-fuel ratio.

_____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Description : _____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Last Answer : Answer: b Explanation: Exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates airfuel ratio while engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting.

The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Description : The economiser is used in boilers to........ A]Increase thermal efficiency of boiler B]Economise on fuel C]Extract heat from the exhaust the gases D]Increase flue gas temperature

Last Answer : A]Increase thermal efficiency of boiler

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Emission of dense white smoke out of the chimney of a thermal power plant is an indication of the use of (A) Less air for combustion (B) Correct amount of air for combustion (C) Too much air for combustion (D) Pulverised coal in boilers

Description : Emission of dense white smoke out of the chimney of a thermal power plant is an indication of the use of (A) Less air for combustion (B) Correct amount of air for combustion (C) Too much air for combustion (D) Pulverised coal in boilers

Last Answer : (C) Too much air for combustion

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Description : In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Description : Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Last Answer : (D) Lump coal (fixed on chain grate)

Pick out the wrong statement. (A) In solvent extraction, the distribution co-efficient should be as large as possible for solvent economy (B) With increase in pressure, the solubility of gases in solvent increases at a fixed temperature (C) Decrease in Murphree plate efficiency is an indication of entrainment in distillation column (D) The capacity of a distillation column is maximum at total reflux

Description : Pick out the wrong statement. (A) In solvent extraction, the distribution co-efficient should be as large as possible for solvent economy (B) With increase in pressure, the solubility of ... in distillation column (D) The capacity of a distillation column is maximum at total reflux

Last Answer : (D) The capacity of a distillation column is maximum at total reflux

If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Description : If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Last Answer : ANSWER : B

In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : (3) compressing air in the cylinders Explanation: Diesel engines use the heat of compressed air to ignite the fuel (intakes air, compresses it, then injects fuel). Diesel engines need high compression ratios to generate the high temperatures required for fuel auto ignition.

In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : compressing air in the cylinders