In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

In general, the limit of inflammability/explosion limit of fuel gases is
widened by the
(A) Increase in gas pressure
(B) Increase in temperature (i.e. preheating)
(C) Use of pure oxygen for combustion instead of air
(D) All (A), (B) & (C)
by

1 Answer

Answer :

(D) All (A), (B) & (C)
by

Related questions

__________ has the widest inflammability limit (explosion limit) of all the gases. (A) Hydrogen (B) Carbon monoxide (C) Acetylene (D) Methane

Description : __________ has the widest inflammability limit (explosion limit) of all the gases. (A) Hydrogen (B) Carbon monoxide (C) Acetylene (D) Methane

Last Answer : (C) Acetylene

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Description : Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Last Answer : (B) Reducing sulphur content in the fuel

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Description : Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Last Answer : preheating the boiler feed water

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Which of the following gases is having the widest explosion limit (about 2 to 81% gas in gas-air mixture), rendering it the property of the most explosive gas? (A) Hydrogen (B) Acetylene (C) Carbon monoxide (D) Ammonia

Description : Which of the following gases is having the widest explosion limit (about 2 to 81% gas in gas-air mixture), rendering it the property of the most explosive gas? (A) Hydrogen (B) Acetylene (C) Carbon monoxide (D) Ammonia

Last Answer : (B) Acetylene

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of staged packed bed reactors carrying out exothermic reaction, use (A) High recycle for pure gas (B) Plug flow for dilute liquid requiring no large preheating of feed (C) Cold shot operations for a dilute solution requiring large preheating to bring the stream upto the reaction temperature (D) All (A), (B) and (C)

Description : In case of staged packed bed reactors carrying out exothermic reaction, use (A) High recycle for pure gas (B) Plug flow for dilute liquid requiring no large preheating of feed (C) Cold shot operations for a ... preheating to bring the stream upto the reaction temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Description : Flue gas obtained on complete combustion of pure acetylene (a hydrocarbon fuel) will contain (A) CO (B) CO2 (C) H2O (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Description : Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Last Answer : (B) Natural gas

Explosion limit of blast furnace gas is 37 to 71% gas in gas-air mixture. It means that the blast furnace gas will explode when burnt in a confined space, if its concentration in the gas-air mixture is __________ percent. (A) < 37% (B) > 71% (C) In between 37 & 71% (D) None of these

Description : Explosion limit of blast furnace gas is 37 to 71% gas in gas-air mixture. It means that the blast furnace gas will explode when burnt in a confined space, if its concentration in the gas-air mixture is __________ percent. (A) < 37% (B) > 71% (C) In between 37 & 71% (D) None of these

Last Answer : (C) In between 37 & 71%

The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Last Answer : (C) 85

Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Description : Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Last Answer : (B) Flame temperature

Which of the following is the most suitable for preheating combustion air above 650°C? (A) Regenerator (B) Metallic recuperator (C) Ceramic recuperator (D) None of these

Description : Which of the following is the most suitable for preheating combustion air above 650°C? (A) Regenerator (B) Metallic recuperator (C) Ceramic recuperator (D) None of these

Last Answer : (C) Ceramic recuperator

Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000

Description : Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000

Last Answer : (B) 650

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Last Answer : (A) Flash point

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Description : Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Last Answer : (D) Carbon monoxide

Mercaptans are added to liquefied petroleum gas (LPG) to (A) Reduce its cost (B) Narrow down its explosion limit (C) Assist in checking its leakage from cylinder (D) Increase its calorific value

Description : Mercaptans are added to liquefied petroleum gas (LPG) to (A) Reduce its cost (B) Narrow down its explosion limit (C) Assist in checking its leakage from cylinder (D) Increase its calorific value

Last Answer : (C) Assist in checking its leakage from cylinder

It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Description : It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Last Answer : a. As oxygen not used for combustion is heated and discharged with the exhaust gases.

Which of the following findings in the patient who has sustained a head injury indicate increasing intracranial pressure (ICP)? a) Widened pulse pressure Additional signs of increasing ICP include increasing systolic blood pressure, bradycardia, rapid respirations, and rapid rise in body temperature.

Description : Which of the following findings in the patient who has sustained a head injury indicate increasing intracranial pressure (ICP)? a) Widened pulse pressure Additional signs of increasing ICP ... regarded as unfavorable because hyperthermia may indicate brain stem damage, a poor prognostic sign.

Last Answer : a) Widened pulse pressure Additional signs of increasing ICP include increasing systolic blood pressure, bradycardia, rapid respirations, and rapid rise in body temperature.

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Ignition temperature of a fuel in air is __________ that in pure oxygen. (A) More than(B) Less than(C) Equal to(D) Either more or less; depends on the type of fuel

Description : Ignition temperature of a fuel in air is __________ that in pure oxygen. (A) More than (B) Less than (C) Equal to (D) Either more or less; depends on the type of fuel

Last Answer : (A) More than

The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Description : The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Last Answer : (A) Much lower

Preheating of coal charge for the coke ovens reduces the (A) Time of carbonisation (B) Yield of gas and tar(C) Fuel consumption in coking(D) All (A), (B) and (C)

Description : Preheating of coal charge for the coke ovens reduces the (A) Time of carbonisation (B) Yield of gas and tar (C) Fuel consumption in coking (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature (C) Electrostatic precipitator is the most efficient dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Description : Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Last Answer : d. All of above

measures oxygen and temperature of the flue gas. a) Fuel efficiency monitor. b) Combustion analyzer. c) Contact thermometer. d) Infrared thermometer.

Description : measures oxygen and temperature of the flue gas. a) Fuel efficiency monitor. b) Combustion analyzer. c) Contact thermometer. d) Infrared thermometer.

Last Answer : Combustion analyzer

If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Description : If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Last Answer : ANSWER a. increase

In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Last Answer : Ans :c

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas