If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

If the specific heat of gaseous products of combustion of a fuel is high,
the abiabatic flame temperature will be
(A) Low
(B) High
(C) Very high, if the fuel is of low calorific value
(D) None of these
by

1 Answer

Answer :

(A) Low(A) Low
by

Related questions

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

The optimum percentage of excess air for combustion depends upon the__________ of the fuel.(A) Type (solid, liquid or gaseous)(B) Calorific value(C) Sulphur content(D) Ignition temperature

Description : The optimum percentage of excess air for combustion depends upon the__________ of the fuel. (A) Type (solid, liquid or gaseous) (B) Calorific value (C) Sulphur content (D) Ignition temperature

Last Answer : (A) Type (solid, liquid or gaseous)

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Description : Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Last Answer : (C) Both (A) & (B)

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Description : With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Last Answer : (D) May increase or decrease; depends on the quantity of products of combustion

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are normally carried out at about __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Last Answer : (B) 900-1000

During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Description : During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Last Answer : (A) Lengthens the flame

Junker's calorimeter is used to determine the calorific value of (A) Pulverised coal (B) Gaseous fuels (C) Fuel oil (D) None of these

Description : Junker's calorimeter is used to determine the calorific value of (A) Pulverised coal (B) Gaseous fuels (C) Fuel oil (D) None of these

Last Answer : (B) Gaseous fuels

Presence of __________ in a dry gaseous fuel does not contribute to its calorific value. (A) Sulphur (B) Oxygen (C) Hydrogen (D) Carbon

Description : Presence of __________ in a dry gaseous fuel does not contribute to its calorific value. (A) Sulphur (B) Oxygen (C) Hydrogen (D) Carbon

Last Answer : (B) Oxygen

Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Description : Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Last Answer : (B) Flame temperature

Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas because of the color of the flame, when it is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Description : Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas ... is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Last Answer : (B) Acetylene gas cannot be used for illumination purpose

For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Description : For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Last Answer : (A) High volatile matter

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

Low temperature carbonisation of coal produces (A) Metallurgical coke (B) Soft coke (C) Very low calorific value coke oven gas (D) No by-products

Description : Low temperature carbonisation of coal produces (A) Metallurgical coke (B) Soft coke (C) Very low calorific value coke oven gas (D) No by-products

Last Answer : (B) Soft coke

Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Description : Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Last Answer : (D) None of these

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Description : Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Last Answer : (C) Friability & oxygen content

Gross and net calorific value of a fuel will be the same (A) If its ash content is zero (B) If its carbon content is very low (C) If its hydrogen/hydrogen compound content is zero (D) Under no circumstances

Description : Gross and net calorific value of a fuel will be the same (A) If its ash content is zero (B) If its carbon content is very low (C) If its hydrogen/hydrogen compound content is zero (D) Under no circumstances

Last Answer : (C) If its hydrogen/hydrogen compound content is zero

Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C(A) Sensible (B) Latent (C) Sensible and latent (D) None of these.

Description : Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C. (A) Sensible (B) Latent (C) Sensible and latent (D) None of these

Last Answer : (C) Sensible and latent

Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Description : Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Last Answer : (C) Heat of combustion

White smoke coming out of the chimney of a furnace indicates the useof(A) Low excess air(B) Very high excess air(C) Gaseous fuel in the furnace(D) Liquid fuel in the furnace

Description : White smoke coming out of the chimney of a furnace indicates the useof (A) Low excess air (B) Very high excess air (C) Gaseous fuel in the furnace (D) Liquid fuel in the furnace

Last Answer : (B) Very high excess air

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Description : Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Last Answer : (A) Amount of heat liberated

Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Description : Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Last Answer : (A) Requires larger combustion chamber than rich gaseous fuel

Pick out the wrong statement. (A) Aromatics have higher specific gravity than paraffins (B) Gross calorific value (GCV) of petrofuels is equal to (12400 - 2100 ρ 2 ) where, ρ is the specific gravity of the fuel at 15.5°C (C) Heavier petrofuels have higher GCV on weight basis (i.e., Kcal/kg) but lower GCV on volume basis (i.e., Kcal/litre) (D) Higher specific gravity of petrofuels means higher C/H ratio

Description : Pick out the wrong statement. (A) Aromatics have higher specific gravity than paraffins (B) Gross calorific value (GCV) of petrofuels is equal to (12400 - 2100 ρ 2 ) where, ρ is the specific gravity ... volume basis (i.e., Kcal/litre) (D) Higher specific gravity of petrofuels means higher C/H ratio

Last Answer : (C) Heavier petrofuels have higher GCV on weight basis (i.e., Kcal/kg) but lower GCV on volume basis (i.e., Kcal/litre)

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation(C) Ignites easily and burns with long smoky flame(D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following gaseous fuels has the lowest calorific value? (A) Gobar gas (B) Refinery gas (C) Converter gas (D) Blast furnace gas

Description : Which of the following gaseous fuels has the lowest calorific value? (A) Gobar gas (B) Refinery gas (C) Converter gas (D) Blast furnace gas

Last Answer : (D) Blast furnace gas

Bomb calorimeter is used for the determination of calorific value of the __________ fuels. (A) Gaseous (B) Solid(C) Liquid(D) Both (B) and (C)

Description : Bomb calorimeter is used for the determination of calorific value of the __________ fuels. (A) Gaseous (B) Solid (C) Liquid (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Which of the following gaseous fuels is likely to have the highest gross calorific value? (A) Sewage gas (B) LPG (C) Producer gas (D) Natural gas

Description : Which of the following gaseous fuels is likely to have the highest gross calorific value? (A) Sewage gas (B) LPG (C) Producer gas (D) Natural gas

Last Answer : (B) LPG

Which of the following gaseous fuels has the highest net calorific value (kcal/Nm3 )? (A) Producer gas (B) Carburetted water gas (C) Natural gas (D) Liquefied petroleum gas

Description : Which of the following gaseous fuels has the highest net calorific value (kcal/Nm3 )? (A) Producer gas (B) Carburetted water gas (C) Natural gas (D) Liquefied petroleum gas

Last Answer : (D) Liquefied petroleum gas

Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Last Answer : (B) Better combustion