'Six-tenth factor' rule is used for estimating the (A) Equipment installation cost (B) Equipment cost by scaling (C) Cost of piping (D) Utilities cost

'Six-tenth factor' rule is used for estimating the
(A) Equipment installation cost
(B) Equipment cost by scaling
(C) Cost of piping
(D) Utilities cost
by

1 Answer

Answer :

(B) Equipment cost by scaling
by

Related questions

Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Description : Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Last Answer : (B) 0.6

Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of the following components of fixed capital investment requires minimum percentage of it? (A) Electrical installation cost (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Description : Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of ... (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Last Answer : (D) Equipment insulation cost

Gas Piping Installation?

Description : Gas Piping Installation?

Last Answer : form_title=Gas Piping Installation form_header=8883 How would you best describe the scope of the work? (Select all that apply)*= [] Repair leak in gas line [] Replace old gas lines [] Appliance gas ... Dryer [] Stove/oven/cooktop [] Central heating system [] Water heater [] Generator [] Other

The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Description : The mechanical splice is best suited for ∙ A. quicker installation under ideal condition ∙ B. minimum attenuation losses ∙ C. field service conditions ∙ D. situations in which cost of equipment is not a factor

Last Answer : D. situations in which cost of equipment is not a factor

Themechanicalsplice isbestsuited for a. quicker installation under ideal conditions b. minimum attenuation losses c. field service conditions d. situations in which cost of equipment is not a factor

Description : Themechanicalsplice isbestsuited for a. quicker installation under ideal conditions b. minimum attenuation losses c. field service conditions d. situations in which cost of equipment is not a factor

Last Answer : c. field service conditions

During the installation of SAP XSS you have to select the Usage Types that should be installedWhich Usage Types are necessary for the installation of SAP XSS? Note: there are 2 correct answered to this question A. Utilities Customer E-Services B. Enterprise Portal C. Adobe Document Services D. Self Services

Description : During the installation of SAP XSS you have to select the Usage Types that should be installedWhich Usage Types are necessary for the installation of SAP XSS? Note: there are 2 correct answered ... . Utilities Customer E-Services B. Enterprise Portal C. Adobe Document Services D. Self Services

Last Answer : D. Self Services

______ information can be derived from the financial accounting systems - utilities cost centre a) Plant level b) Plant department level c) System level d) Equipment level

Description : ______ information can be derived from the financial accounting systems - utilities cost centre a) Plant level b) Plant department level c) System level d) Equipment level

Last Answer : plant level

According to six-tenths-factor rule, if the cost of a given unit at one capacity is known, then the cost of similar unit with '' times the capacity of the first unit is approximately equal to __________ times the cost of the initial unit. (A) n (B) n0.6 (C) n0.4 (D) √n

Description : According to six-tenths-factor rule, if the cost of a given unit at one capacity is known, then the cost of similar unit with '' times the capacity of the first unit is approximately equal to __________ times the cost of the initial unit. (A) n (B) n0.6 (C) n0.4 (D) √n

Last Answer : (B) n0.6

Which of the following is not a component of the fixed capital for a chemical plant facility? (A) Raw materials inventory (B) Utilities plants (C) Process equipment (D) Emergency facilities

Description : Which of the following is not a component of the fixed capital for a chemical plant facility? (A) Raw materials inventory (B) Utilities plants (C) Process equipment (D) Emergency facilities

Last Answer : (A) Raw materials inventory

Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Description : Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Last Answer : (A) Fluid flow rate & friction loss

In an ordinary chemical plant, electrical installation cost may be about (A) 10-15% of purchased equipment cost (B) 3-10% of fixed capital investment (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : In an ordinary chemical plant, electrical installation cost may be about (A) 10-15% of purchased equipment cost (B) 3-10% of fixed capital investment (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (C) Either (A) or (B)

Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Description : Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80

Last Answer : (B) 35 to 45

The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Last Answer : C. the total power available minus the attenuation losses

Cost of piping in a fluid processing unit (e.g., distillation) of a chemical process plant is about __________ percent of the fixed capital investment. (A) 4 (B) 13 (C) 22 (D) 34

Description : Cost of piping in a fluid processing unit (e.g., distillation) of a chemical process plant is about __________ percent of the fixed capital investment. (A) 4 (B) 13 (C) 22 (D) 34

Last Answer : (B) 13

Cost incurred towards __________ in a chemical plant is a component of the utilities cost. (A) Water supply (B) Running a control laboratory (C) Property protection (D) Medical services

Description : Cost incurred towards __________ in a chemical plant is a component of the utilities cost. (A) Water supply (B) Running a control laboratory (C) Property protection (D) Medical services

Last Answer : (A) Water supply

Effluent treatment cost in a chemical plant is categorised as the __________ cost. (A) Fixed (B) Overhead (C) Utilities (D) Capital

Description : Effluent treatment cost in a chemical plant is categorised as the __________ cost. (A) Fixed (B) Overhead (C) Utilities (D) Capital

Last Answer : (C) Utilities

Total product cost of a chemical plant does not include the __________ cost. (A) Market survey (B) Operating labour, supervision and supplies (C) Overhead and utilities (D) Depreciation, property tax and insurance

Description : Total product cost of a chemical plant does not include the __________ cost. (A) Market survey (B) Operating labour, supervision and supplies (C) Overhead and utilities (D) Depreciation, property tax and insurance

Last Answer : (A) Market survey

Utilities cost in the operation of chemical process plant comes under the (A) Plant overhead cost (B) Fixed charges (C) Direct production cost (D) General expenses

Description : Utilities cost in the operation of chemical process plant comes under the (A) Plant overhead cost (B) Fixed charges (C) Direct production cost (D) General expenses

Last Answer : C) Direct production cost

'Utilities' in a chemical process plant includes compressed air, steam, water, electrical power, oxygen, acetylene, fuel gases etc. Utility costs for ordinary chemical process plants ranges roughly from __________ percent of the total product cost. (A) 1 to 5 (B) 10 to 20 (C) 25 to 35 (D) 35 to 45

Description : 'Utilities' in a chemical process plant includes compressed air, steam, water, electrical power, oxygen, acetylene, fuel gases etc. Utility costs for ordinary chemical process plants ranges roughly from __________ percent of the total product ... 1 to 5 (B) 10 to 20 (C) 25 to 35 (D) 35 to 45

Last Answer : (B) 10 to 20

The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Which of the following is a direct project cost? 1. Lighting and heating for the corporate office 2. Workers Compensation insurance 3. Piping for an irrigation project 4. A and B

Description : Which of the following is a direct project cost? 1. Lighting and heating for the corporate office  2. Workers Compensation insurance  3. Piping for an irrigation project  4. A and B

Last Answer : 3. Piping for an irrigation project

Your task is to install an additional application server for an SAP system Which rule applies for the installation work? A. The additional application server has to be installed on a separated host from the primary application server B. The additional application server can be installed using the user sapadm C. The additional application server can be installed using an instance number proposed y the installation tool D. The additional number of the additional application server has to be identical to the instance number of the primary application server.

Description : Your task is to install an additional application server for an SAP system Which rule applies for the installation work? A. The additional application server has to be installed on a ... additional application server has to be identical to the instance number of the primary application server.

Last Answer : A. The additional application server has to be installed on a separated host from the primary application server

A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When installing the new meter it should be __________. A. grounded to the negative side B. connected to a large resistor between the positive side and the ground C. installed exactly as the old installation D. grounded to the positive side

Description : A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When ... side and the ground C. installed exactly as the old installation D. grounded to the positive side

Last Answer : Answer: C

Where online can I find information about stereo equipment installation?

Description : Where online can I find information about stereo equipment installation?

Last Answer : The best place to find information about stereo equipment installation is at Howto.com. This will give you step by step instructions on doing so yourself.

Outdoor Playground Equipment Installation?

Description : Outdoor Playground Equipment Installation?

Last Answer : form_title=Outdoor Playground Equipment Installation form_header=10083 What number of children are going to use the equipment at the same time?*= {Select One,1-3,4-8,9-15,16-25,26-plus} Explain the type of ... who will be using this equipment?*= {Select One,2-5 years,6-11 years,12-plus years}

Where is the best place to look for industrial supplies and equipment for hvlp spray system installation.?

Description : Where is the best place to look for industrial supplies and equipment for hvlp spray system installation.?

Last Answer : The best place to look for hvlp spray system project industrial supplies and equipment would be at www.grainger.com. Grainger is a retailer who uses catalog and internet ordering to provide rapid access to customers seeking industrial supplies.

Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Description : Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Last Answer : Answer: A

The controlling resistance in a rotary drum vacuum filter is the __________ resistance.(A) Piping (B) Cake (C) Filter medium (D) None of these

Description : The controlling resistance in a rotary drum vacuum filter is the __________ resistance. (A) Piping (B) Cake (C) Filter medium (D) None of these

Last Answer : (B) Cake

Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations transmitted through piping and/or supports due to external reasons (D) All (A), (B) and (C)

Description : Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations ... piping and/or supports due to external reasons (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What is the best way to handle bend or turns in slurry piping systems?

Description : What is the best way to handle bend or turns in slurry piping systems?

Last Answer : Even long radius elbows should be avoided in slurry pipes and lines. They are often the site of severe erosion or solid/liquid separation. Only gentle pipe bends or sweeps should be used to turn ... . Industrial experience has shown that a bend-radius-to-pipe-diameter ratio of 3-5 is recommended.

What is some common piping materials used to transport slurries?

Description : What is some common piping materials used to transport slurries?

Last Answer : When selecting a piping material to transport slurries, corrosion and erosion considerations must be accounted for. Some of the most popular piping materials include: ► Carbon Steel ► Stainless ... polyvinyl chloride (uPVC) ► Fiberglass reinforced plastic (FRP) ► Elastomer-lined carbon steel

Are there any general rules that should be considered when designing a slurry piping system? The following are items to consider when designing a piping system that will transport slurries:

Description : Are there any general rules that should be considered when designing a slurry piping system? The following are items to consider when designing a piping system that will transport slurries:

Last Answer : 1) Whenever possible, piping should be designed to be self-draining 2) Manual draining should be installed to drain sections of the piping when self-draining is not possible 3) Blow-out or ... flanges should be provided every 20 feet of horizontal pipe or after every two changes in direction

How much do utilities typically cost in an apartment?

Description : How much do utilities typically cost in an apartment?

Last Answer : Depends where you live, what appliances you have in your house, and how much you use them. I pay about $150 for electricity per month. Another $120 for water and sewer which is lumped ... can approximate what your monthly usage rates will be and come out with an approximation for monthly cost.

I am planning to move to London in 3 months and I am most concern with how much it will cost me to live decently in this place. I found some useful and informative sites regarding accommodation, but I couldn't find something that can figuratively tell me the cost of a decent meal, utilities among others. Can anyone share their knowledge? Anything that can help me compute for my monthly expenses would be most appreciated.

Description : I am planning to move to London in 3 months and I am most concern with how much it will cost me to live decently in this place. I found some useful and informative sites regarding ... anyone share their knowledge? Anything that can help me compute for my monthly expenses would be most appreciated.

Last Answer : answer:CCCCCONGRATULATIONS, YOU MADE THE LARGEST QUESTION YET !!! …and i’m not even gonna bother reading something that long…

Internal costs include a) Developers salaries b) Managers and support personnel salaries c) The cost of overheads such as utilities, rent and senior managers d) Materials (such as manuals) and services such as travel e) All of the above.

Description : Internal costs include a) Developers salaries b) Managers and support personnel salaries c) The cost of overheads such as utilities, rent and senior  managers d) Materials (such as manuals) and services such as travel e) All of the above.

Last Answer : a) Developers salaries

The operating expense section of an income statement for a wholesaler would not include a. freight-out. b. utilities expense. c. cost of goods sold. d. insurance expense

Description : The operating expense section of an income statement for a wholesaler would not include a. freight-out. b. utilities expense. c. cost of goods sold. d. insurance expense

Last Answer : d. insurance expense

Which of these factors factors would be consider be considered when ed when making a location ocation decision decision at the site level? a. government government rules, attitudes, attitudes, stability, stability, incentives incentives b. cultural cultural and economic economic issues c. zoning regulations d. cost and availability availability of utilities utilities e. proximity proximity to raw materials materials and customers

Description : Which of these factors factors would be consider be considered when ed when making a location ocation decision decision at the site level? a. government government rules, attitudes, ... availability availability of utilities utilities e. proximity proximity to raw materials materials and customers

Last Answer : c. zoning regulations

When making a location decision at the region/community level, which of these would be considered? a. government government rules, attitudes, attitudes, stability, stability, incentives incentives b. cultural cultural and economic economic issues c. cost and availability of utilities d. zoning restrictions restrictions e. air, rail, highway, highway, waterway waterway systems

Description : When making a location decision at the region/community level, which of these would be considered? a. government government rules, attitudes, attitudes, stability, stability, incentives incentives b ... d. zoning restrictions restrictions e. air, rail, highway, highway, waterway waterway systems

Last Answer : c. cost and availability of utilities

In location planning, environmental regulations, cost a , cost and availability of utilities, and taxes are a. global factors b. country factors country factors c. regional/community factors d. site-related factors e. none of the above

Description : In location planning, environmental regulations, cost a , cost and availability of utilities, and taxes are a. global factors b. country factors country factors c. regional/community factors d. site-related factors e. none of the above

Last Answer : c. regional/community factors

Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to enable benefits to be realised. c. to take ultimate accountability for the delivery of the business benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Description : Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to ... benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Last Answer : b. to deliver the project objectives to enable benefits to be realised.

Scheduling can best be defined as the process used to determine: a. overall project duration. b. project cost estimating. c. the project management plan. d. sub-contractor’s responsibilities.

Description : Scheduling can best be defined as the process used to determine: a. overall project duration. b. project cost estimating. c. the project management plan. d. sub-contractor’s responsibilities.

Last Answer : a. overall project duration.

Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time. b. to deliver the project objectives to enable benefits to be realised. c. to take ultimate accountability for the delivery of the business benefits. d. to delegate all accountability for managing time, cost and quality to team leaders.

Description : Which statement best describes a responsibility of the project manager: a. to be the sole source of expertise for estimating techniques on cost and time.  b. to deliver the project objectives to ... benefits.  d. to delegate all accountability for managing time, cost and quality to team leaders.

Last Answer : b. to deliver the project objectives to enable benefits to be realised.

Scheduling can best be defined as the process used to determine: a. overall project duration. b. project cost estimating. c. the project management plan.

Description : Scheduling can best be defined as the process used to determine:  a. overall project duration.  b. project cost estimating.  c. the project management plan.

Last Answer : a. overall project duration.

A time-phased budget that project managers use to measure and monitor cost performance. A. Cost Baseline B. Cost Budgeting C. Cost Estimating D. Cost Variance

Description :  A time-phased budget that project managers use to measure and monitor cost performance. A. Cost Baseline B. Cost Budgeting C. Cost Estimating D. Cost Variance

Last Answer : A. Cost Baseline

While estimating the cost of software, Lines of Code (LOC) and Function Points (FP) are used to measure which one of the following? (A) Length of code (B) Size of software (C) Functionality of software (D) None of the above

Description : While estimating the cost of software, Lines of Code (LOC) and Function Points (FP) are used to measure which one of the following? (A) Length of code (B) Size of software (C) Functionality of software (D) None of the above

Last Answer : (B) Size of software

A fair dice is thrown twenty times. The probability that on the tenth throw the fourth six appears is -Maths 9th

Description : A fair dice is thrown twenty times. The probability that on the tenth throw the fourth six appears is -Maths 9th

Last Answer : (c) \(rac{84 imes5^6}{6^{10}}\)In the first nine throws we should have three sixes and six non-sixes and a six in the tenth throw and thereafter whatever face appears, it doesn't matter. ∴ Required probability = 9C3 \(\bigg(rac{1} ... x 1 x 1 ............x 1 {10 times} = \(rac{84 imes5^6}{6^{10}}\).

Open pan evaporators are preferred to be used, when the solution to be concentrated is (A) Scaling (B) Highly viscous (C) Corrosive (D) Salty

Description : Open pan evaporators are preferred to be used, when the solution to be concentrated is (A) Scaling (B) Highly viscous (C) Corrosive (D) Salty

Last Answer : (B) Highly viscous

Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The rate of scaling of furnace stock depends upon the (A) Temperature (B) Time(C) Nature of atmosphere(D) All (A), (B) and (C)

Description : The rate of scaling of furnace stock depends upon the (A) Temperature (B) Time (C) Nature of atmosphere (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Presence of SO2 in furnace gases attacks the ferrous metal by way of (A) Accelerating the rate of scaling (B) Causing metal embrittlement (C) Attacking the grain boundaries; particularly severe on low carbon and nickel bearing steels at high temperature (D) All (A), (B) and (C)

Description : Presence of SO2 in furnace gases attacks the ferrous metal by way of (A) Accelerating the rate of scaling (B) Causing metal embrittlement (C) Attacking the grain boundaries; particularly severe on low carbon and nickel bearing steels at high temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)