Gas Piping Installation?

Gas Piping Installation?
by

1 Answer

Answer :

form_title=Gas Piping Installation form_header=8883 How would you best describe the scope of the work? (Select all that apply)*= [] Repair leak in gas line [] Replace old gas lines [] Appliance gas hook-up [] Supply gas line to appliance(s) in or near the home [] Supply new gas piping from the street to the home [] Other Which of your appliances need gas?*= [] Fireplace [] Barbecue [] Clothes Dryer [] Stove/oven/cooktop [] Central heating system [] Water heater [] Generator [] Other
by

Related questions

'Six-tenth factor' rule is used for estimating the (A) Equipment installation cost (B) Equipment cost by scaling (C) Cost of piping (D) Utilities cost

Description : 'Six-tenth factor' rule is used for estimating the (A) Equipment installation cost (B) Equipment cost by scaling (C) Cost of piping (D) Utilities cost

Last Answer : (B) Equipment cost by scaling

Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of the following components of fixed capital investment requires minimum percentage of it? (A) Electrical installation cost (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Description : Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of ... (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Last Answer : (D) Equipment insulation cost

How Do You Carry Out Piping For A Different Pressure Flow Transmitter On Liquids, Gas And Steam Services? Why?

Description : How Do You Carry Out Piping For A Different Pressure Flow Transmitter On Liquids, Gas And Steam Services? Why?

Last Answer : Liquid lines: On liquid lines the transmitter is mounted below the orifice plate. Since liquids have a property of self draining. Gas Service: On gas service the transmitter is mounted above the orifice ... mounted below the orifice plate with condenlate pots. The pots should be at the same level.

Late afternoons I often bathe. I'll soak in water piping hot. My essence goes through my see through clothes. Used up am I; I've gone to pot. What am I? -Riddles

Description : Late afternoons I often bathe. I'll soak in water piping hot. My essence goes through my see through clothes. Used up am I; I've gone to pot. What am I? -Riddles

Last Answer : I'm a tea bag!

What can be done to avoid fire hazards caused by bad piping?

Description : What can be done to avoid fire hazards caused by bad piping?

Last Answer : One way is to check for bad leakage. A water coming from the leakage can seep into the area of electrical wiring that could cause fire. Keep an eye for high water bill or any form of discoloration that might indicate leak to avoid hazards.

What is the Piping colour code of N butanol solvent?

Description : What is the Piping colour code of N butanol solvent?

Last Answer : What is the answer ?

What is the N butanol piping colour code?

Description : What is the N butanol piping colour code?

Last Answer : What is the answer ?

What do the piping connections to a steam boiler provide?

Description : What do the piping connections to a steam boiler provide?

Last Answer : Need answer

Is there a difference between gray and white PVC piping and fittings?

Description : Is there a difference between gray and white PVC piping and fittings?

Last Answer : The only difference between gray and white PVC piping is in the color. They're both PVC.

What kind of material is usually used for residential piping?

Description : What kind of material is usually used for residential piping?

Last Answer : Yes you are correct the material usually used for residential piping is indeed copper. It is the cheapest and lowest maintenance materials out there.

Different Types of Flanges Used in Piping Applications?

Description : Different Types of Flanges Used in Piping Applications?

Last Answer : Different Types of Flanges Slip on Flanges Weld Neck Flanges Blind Flanges Socket Weld Flanges Lap Joint Flanges Threaded Flanges Orifice Flanges Spectacle Blind Flanges Reducing Flanges Forged Flanges ANSI ... If anyone wants to buy any of these Flanges then Contact us: sales@nufitpiping .com

What is the difference between pipeline and piping?

Description : What is the difference between pipeline and piping?

Last Answer : piping deals with small sized pipes used for domestic use or small scale industry use with less transportation capacity.Pipeline Engg deals with transports of hydrocarbons with huge capacity through long ... to transfer fluid from one facility to another within those boundaries as required.-----

The controlling resistance in a rotary drum vacuum filter is the __________ resistance.(A) Piping (B) Cake (C) Filter medium (D) None of these

Description : The controlling resistance in a rotary drum vacuum filter is the __________ resistance. (A) Piping (B) Cake (C) Filter medium (D) None of these

Last Answer : (B) Cake

Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations transmitted through piping and/or supports due to external reasons (D) All (A), (B) and (C)

Description : Vibrations in the tubes of a shell and tube heat exchanger is induced due to the (A) Flow of fluid on the tube and shell sides (B) Oscillations in the flow of shell/tube sides fluid (C) Vibrations ... piping and/or supports due to external reasons (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following is a direct project cost? 1. Lighting and heating for the corporate office 2. Workers Compensation insurance 3. Piping for an irrigation project 4. A and B

Description : Which of the following is a direct project cost? 1. Lighting and heating for the corporate office  2. Workers Compensation insurance  3. Piping for an irrigation project  4. A and B

Last Answer : 3. Piping for an irrigation project

Piping is carried out in a. Chrysanthemum b. Rose c. Gladiolus d. Carnation

Description : Piping is carried out in a. Chrysanthemum b. Rose c. Gladiolus d. Carnation

Last Answer : Carnation

Griffin go to ............ after London. (a) Piping (b) Iping(c) Snowland (d) none of the above

Description : Griffin go to ............ after London. (a) Piping (b) Iping(c) Snowland (d) none of the above

Last Answer : ) Iping(

Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Description : Two piping system are said to be equivalent, when the __________ are same. (A) Fluid flow rate & friction loss (B) Length & friction factor (C) Diameter & friction factor (D) Length & diameter

Last Answer : (A) Fluid flow rate & friction loss

Cost of piping in a fluid processing unit (e.g., distillation) of a chemical process plant is about __________ percent of the fixed capital investment. (A) 4 (B) 13 (C) 22 (D) 34

Description : Cost of piping in a fluid processing unit (e.g., distillation) of a chemical process plant is about __________ percent of the fixed capital investment. (A) 4 (B) 13 (C) 22 (D) 34

Last Answer : (B) 13

Pick up the true statement from the following: (A) Plain ceiling provides the best property diffusing light (B) In the absence of beams, it is easier to install piping (C) In the absence of beams, it is easier to paint (D) All the above

Description : Pick up the true statement from the following: (A) Plain ceiling provides the best property diffusing light (B) In the absence of beams, it is easier to install piping (C) In the absence of beams, it is easier to paint (D) All the above

Last Answer : Answer: Option D

What do you mean by Stress? What are the types of Stresses that are generated in a Piping?

Description : What do you mean by Stress? What are the types of Stresses that are generated in a Piping?

Last Answer : Answer: Whenever a force is applied to any object it applies a reaction force against the deformation by that force. That reaction force per unit area is the measure for the generated stress. ... Radial Stress 5. Expansion Stress 6. Stress due to occasional events like Seismic and Wind effects.

What points to be considered for reciprocating compressor piping layout?

Description : What points to be considered for reciprocating compressor piping layout?

Last Answer : Answer: High pulsation, simple line as low to grade as possible for supporting, analog study, all branches close to line support and on top, Isolate line support from adjacent compressor or building foundations

What is the software available for performing piping stress analysis?

Description : What is the software available for performing piping stress analysis?

Last Answer : Answer: Caesar II, AutoPipe etc.

Which Piping code is used for Power piping and which code is used for Process Piping design?

Description : Which Piping code is used for Power piping and which code is used for Process Piping design?

Last Answer : Answer: • Power Piping: ASME B 31.1 • Process Piping: ASME B 31.3

How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Description : How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Last Answer : 1. The inlet as well as exhaust steam lines should be firmly supported to avoid strains from being imposed on the turbine. 2. Adequate allowance should be made for expansion of steam pipes due to heat.

How to provide Flexibility in the Piping system ?

Description : How to provide Flexibility in the Piping system ?

Last Answer : By change in direction using Pipe bends, Expansion loops, Expansion joints etc

What is Flexibility of the Piping System?

Description : What is Flexibility of the Piping System?

Last Answer : Ability to absorb thermal growth of the piping system

What is the best way to handle bend or turns in slurry piping systems?

Description : What is the best way to handle bend or turns in slurry piping systems?

Last Answer : Even long radius elbows should be avoided in slurry pipes and lines. They are often the site of severe erosion or solid/liquid separation. Only gentle pipe bends or sweeps should be used to turn ... . Industrial experience has shown that a bend-radius-to-pipe-diameter ratio of 3-5 is recommended.

What is some common piping materials used to transport slurries?

Description : What is some common piping materials used to transport slurries?

Last Answer : When selecting a piping material to transport slurries, corrosion and erosion considerations must be accounted for. Some of the most popular piping materials include: ► Carbon Steel ► Stainless ... polyvinyl chloride (uPVC) ► Fiberglass reinforced plastic (FRP) ► Elastomer-lined carbon steel

Are there any general rules that should be considered when designing a slurry piping system? The following are items to consider when designing a piping system that will transport slurries:

Description : Are there any general rules that should be considered when designing a slurry piping system? The following are items to consider when designing a piping system that will transport slurries:

Last Answer : 1) Whenever possible, piping should be designed to be self-draining 2) Manual draining should be installed to drain sections of the piping when self-draining is not possible 3) Blow-out or ... flanges should be provided every 20 feet of horizontal pipe or after every two changes in direction

Which of the following is not recommended by ASME B31.3 when assembling gray cast iron flanges? a) Use high strength bolting at all times. b) Carefully align the flanges. c) Carefully control bolt torque. d) Ensure piping loads transmitted to the flanges are within design conditions.

Description : Which of the following is not recommended by ASME B31.3 when assembling gray cast iron flanges? a) Use high strength bolting at all times. b) Carefully align the flanges. c) Carefully control bolt torque. d) Ensure piping loads transmitted to the flanges are within design conditions.

Last Answer : a) Use high strength bolting at all times.

Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and 40,000 psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength

For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of the bolts to prevent leakage. c) Immediate replacement is recommended if the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Description : For joints in service in the creep range which of the following is recommended by ASME B16.5? a) Replacement of the joint after 1,000,000 hours of service. b) Periodic tightening of ... the material operates in the creep range. d) Regular flow detection inspection of the piping to fitting welds.

Last Answer : b) Periodic tightening of the bolts to prevent leakage.

What size piping flanges and flanged fittings are addressed by ASME B16.5? a) 1/2" to 24" NPS. b) 1" to 36" NPS. c) 1/4" to 36" NPS. d) 1/4 to 48" NPS.

Description : What size piping flanges and flanged fittings are addressed by ASME B16.5? a) 1/2" to 24" NPS. b) 1" to 36" NPS. c) 1/4" to 36" NPS. d) 1/4 to 48" NPS.

Last Answer : a) 1/2" to 24" NPS.

Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) kidney defect (iv) All above are correct

Description : Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) kidney defect (iv) All above are correct

Last Answer : (i) Lack of fusion (Heat losses)*

Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) Half moon defect (iv) None of above

Description : Late tapping will cause defect of? (i) Lack of fusion (Heat losses)* (ii) Piping defect (iii) Half moon defect (iv) None of above

Last Answer : (i) Lack of fusion (Heat losses)*

Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) Due to continuous passage of water through a series of well connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Description : Piping in a soil mass is a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit* b) Caused due to very low exit gradient c) ... connected pores d) Due to loss of the strength of cohesion less soil because of upward flow of of water

Last Answer : a) Erosion of subsoil by the high velocities of flow of water through it when such velocities exceed a certain limit*

How much is the avg. gas fireplace installation cost in the U.S.?

Description : How much is the avg. gas fireplace installation cost in the U.S.?

Last Answer : The average gas fireplace installation cost is about $500. It is cheaper than a wood burning foreplace installation.

What changes will be made to my fireplace during the installation of gas logs?

Description : What changes will be made to my fireplace during the installation of gas logs?

Last Answer : First you must figure out if is a vented or non vented gas logs. Also you must inspect you fireplace to make sure it can use gas logs. Most fireplaces can use gas logs so you shouldn't face many changes.

What is the importance of developing Chabahar Port by India? (1) India's trade with African countries will enormously increase. (2) India's relations with oil-producing Arab countries will be strengthened. (3) India will not depend on Pakistan for access to Afghanistan and Central Asia. (4) Pakistan will facilitate and protect the installation of a gas pipeline between Iraq and India.

Description : What is the importance of developing Chabahar Port by India? (1) India's trade with African countries will enormously increase. (2) India's relations with oil-producing Arab countries will be ... (4) Pakistan will facilitate and protect the installation of a gas pipeline between Iraq and India.

Last Answer : (3) India will not depend on Pakistan for access to Afghanistan and Central Asia. Explanation: In May 2016, India and Iran signed the "historic" Chabahar port agreement, which has the potential of becoming India's gateway to Afghanistan, Central Asia and Europe. So, C is the most fitting answer.