The shape factor of standard rolled beam section varies from
(A) 1.10 to 1.20
(B) 1.20 to 1.30
(C) 1.30 to 1.40
(D) 1.40 to 1.50
Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm
Last Answer : Answer: Option C
Description : For an I beam, the shape factor is 1.12. If the allowable stress (with factor of safety in bending as 1.5) is increased by 20% for wind and earthquake loads, the modified load factor is (a) 1.10 (b) 1.25 (c) 1.35 (d) 1.40
Last Answer : (d) 1.40
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The ... will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne
Last Answer : (C) 40 kg/tonne
Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope ... arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E
Last Answer : (D) 200/E
Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm
Last Answer : Answer: Option D
Description : The head light of vehicles should be such that its lower beam illuminates objects at (A) 10 m (B) 20 m (C) 30 m (D) 40 m
Description : Minimum clear cover (in mm) to the main steel bars in slab, beam, column and footing respectively, are (a) 10, 15, 20 and 25 (b) 15, 25, 40 and 75 (c ) 20, 25, 30 and 40 (d) 20, 35, 40 and 75
Last Answer : (b) 15, 25, 40 and 75
Description : The diameter of the Vicat plunger is 10 mm and its length varies form [ A ] 40 mm [ B ] 50 mm [ C ] 55 mm [ D ] 60 mm
Last Answer : [ B ] 50 mm
Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above
Last Answer : (c) 15 percent
Description : What is the spectral width of a standard LED? ∙ A. 20 to 40 nm ∙ B. 30 to 50 nm ∙ C. 10 to 30 nm ∙ D. 40 to 60 nm
Last Answer : 30 to 50 nm
Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these
Last Answer : (A) - 0.000909 m
Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : Cross slope of the formation to have good drainage of Ballast section is a) 1 in 40* b) 1 in 50 c) 1 in 30 d) 1 in 20
Last Answer : a) 1 in 40*
Description : The standard height of a standard rain gauge, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 50 cm
Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Description : In case of Raymond pile (A) Lengths vary from 6 m to 12 m (B) Diameter of top of piles varies from 40 cm to 60 cm (C) Diameter of pile at bottom varies from 20 cm to 28 cm (D) All the above
Description : 0 Pick up the correct statement from the following: (A) The point through which the resultant of the shear stresses passes is known as shear centre (B) In the standard rolled channels, the shear centre ... horizontal plane and away from the C.G., outside of the leg projection (D) All the above
Last Answer : (D) All the above
Description : The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm
Last Answer : Answer: Option A
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %
Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm
Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section
Description : The percentage of chlorine in fresh bleaching powder is roughly (A) 50 to 60 (B) 30 to 35 (C) 40 to 50 (D) 20 to 25
Last Answer : (B) 30 to 35
Description : From the point of tangency before an intersection, the route markers are fixed at a distance of (A) 15 m to 30 m (B) 20 m to 35 m (C) 40 m to 50 m (D) 100 m to 150
Description : The minimum design speed for hairpin bends in hill roads is taken as (A) 20 kmph (B) 30 kmph (C) 40 kmph (D) 50 kmph
Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm
Description : What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Last Answer : Answer: C
Description : In plastic analysis, the shape factor for a circular section, is (A) 1.5 (B) 1.6 (C) 1.7 (D) 1.75
Last Answer : (C) 1.7
Description : In plastic analysis, the shape factor for a triangular section, is (A) 1.5 (B) 1.34 (C) 2.34 (D) 2.5
Last Answer : (C) 2.34
Description : In plastic analysis, the shape factor for rectangular section, is (A) 1.4 (B) 1.5 (C) 1.6 (D) 1.7
Last Answer : (B) 1.5
Description : If the shape factor of a section is 1.5 and the factor of safety to be adopted is 2, then the load factor will be (a) 3 (b) 4 (c) 1.5 (d) 2
Last Answer : (a) 3
Description : The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for maximum strength are: (A) b = 57.73 cm d = 81.65 cm (B) b = 81.65 cm d = 57.73 cm (C) b = 50.00 cm d = 50.00 cm (D) b = 40.00 cm d = 80.00 cm
Last Answer : (A) b = 57.73 cm d = 81.65 cm
Description : Neutral atmosphere is maintained in a/an __________ furnace. (A) Cold rolled steel coil annealing (B) Open hearth (C) Soaking pit (D) Walking beam reheating
Last Answer : (A) Cold rolled steel coil annealing
Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above
Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45
Description : In the American standard, the aural transmitter maximum radiated power is _____ of peak visual transmitter power. A. 10 % B. 30 % C. 20 % D. 40 %
Last Answer : C. 20 %
Description : What is the baud rate of the standard 10 Mbps Ethernet ? (A) 10 megabaud (B) 20 megabaud (C) 30 megabaud (D) 40 megabaud
Last Answer : (B) 20 megabaud
Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm
Last Answer : (C) 25 cm
Description : Normal serum free testosterone in adult women varies between (A) 0.0–0.2 ng/dl (B) 0.3–2 ng/dl (C) 10–30 ng/dl (D) 50–100 ng/dl
Last Answer : Answer : B
Description : Normal serum free testosterone in adult men varies between (A) 1–5 ng/dl (B) 6–9 ng/dl (C) 10–30 ng/dl (D) 50–100 ng/dl 214 MCQs IN BIOCHEMISTRY
Last Answer : Answer : C
Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm
Description : The normal serum concentration of ceruloplasmin in mg/100 ml varies between (A) 5–10 (B) 10–20 (C) 25–43 (D) 50–100
Description : Depending upon the size of the tractor the width of the tracks varies for a) 10-50 cm b) 15.50 cm c) 20 – 25 cm d) 25-50 cm
Last Answer : c) 20 – 25 cm
Description : In a shaft rotated by a couple, the shear force varies (A) From zero at the centre to a maximum at the circumference (B) From minimum at the centre of maximum at the circumference (C) From maximum at the centre to zero at the circumference (D) Equally throughout the section
Last Answer : (A) From zero at the centre to a maximum at the circumference
Description : Consider the following statements : 1. There is no flow across a streamline 2. Streamline spacing varies directly with velocity at the section 3. Streamlines do not cross 4. In steady flow, streamline pattern does not change with ... 4 (b) 1 and 2 only (c) 1, 3 and 4 only (d) 2, 3 and 4 only
Last Answer : (c) 1, 3 and 4 only
Description : The agreed standard for measuring loudness is the loudness sensation produced by a 1000 Hz sine wave _____ dB above the listener’s threshold of hearing. A. 80 B. 50 C. 30 D. 40
Last Answer : D. 40
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2