In plastic analysis, the shape factor for a triangular section, is (A) 1.5 (B) 1.34 (C) 2.34 (D) 2.5

In plastic analysis, the shape factor for a triangular section, is 

(A) 1.5 

(B) 1.34 

(C) 2.34 

(D) 2.5 

by

1 Answer

Answer :

(C) 2.34 

by

Related questions

In plastic analysis, the shape factor for a circular section, is (A) 1.5 (B) 1.6 (C) 1.7 (D) 1.75

Description : In plastic analysis, the shape factor for a circular section, is  (A) 1.5  (B) 1.6  (C) 1.7  (D) 1.75 

Last Answer : (C) 1.7 

In plastic analysis, the shape factor for rectangular section, is (A) 1.4 (B) 1.5 (C) 1.6 (D) 1.7

Description : In plastic analysis, the shape factor for rectangular section, is  (A) 1.4  (B) 1.5  (C) 1.6  (D) 1.7

Last Answer : (B) 1.5 

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is (A) Square (B) Rectangular (C) Trapezoidal (D) Triangular

Description : If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is (A) Square (B) Rectangular (C) Trapezoidal (D) Triangular

Last Answer : Answer: Option B

The stone blocks approximately triangular in shape, used as steps, are known (A) Stone steps (B) Built up steps (C) Spandril steps (D) None of the

Description : The stone blocks approximately triangular in shape, used as steps, are known (A) Stone steps (B) Built up steps (C) Spandril steps (D) None of these

Last Answer : Answer: Option C

The ratio of moments of inertia of a triangular section about its base and about a centroidal axis parallel to its base, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 3.0

Description : The ratio of moments of inertia of a triangular section about its base and about a centroidal axis  parallel to its base, is  (A) 1.0  (B) 1.5  (C) 2.0  (D) 3.0 

Last Answer : (D) 3.0 

If the shape factor of a section is 1.5 and the factor of safety to be adopted is 2, then the load factor will be (a) 3 (b) 4 (c) 1.5 (d) 2

Description : If the shape factor of a section is 1.5 and the factor of safety to be adopted is 2, then the load factor will be (a) 3 (b) 4 (c) 1.5 (d) 2

Last Answer : (a) 3

The moment of inertia of a triangular section (height h, base b) about its base, is (A) bh²/12 (B) b²h/12 (C) bh3 /12(D) b 3h/12

Description : The moment of inertia of a triangular section (height h, base b) about its base, is  (A) bh²/12  (B) b²h/12  (C) bh3 /12  (D) b 3h/12 

Last Answer : (C) bh3 /12 

For the same height, the bottom width for no tension, (A) For triangular section is more than rectangular section (B) For rectangular section is more than triangular section (C) For triangular section is same as that of a rectangular section (D) None of these

Description : For the same height, the bottom width for no tension,  (A) For triangular section is more than rectangular section  (B) For rectangular section is more than triangular section  (C) For triangular section is same as that of a rectangular section  (D) None of these 

Last Answer : (C) For triangular section is same as that of a rectangular section 

A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Description : A triangular section having base b, height h, is placed with its base horizontal. If the shear stress at a depth y from top is q, the maximum shear stress is (A) 3S/bh (B) 4S/bh (C) 4b/Sh (D) 3b/bS

Last Answer : (A) 3S/bh

The most efficient section of a channel is (A) Triangular (B) Rectangular (C) Square (D) Trapezoidal

Description : The most efficient section of a channel is (A) Triangular (B) Rectangular (C) Square (D) Trapezoidal

Last Answer : Answer: Option D

The shape factor of standard rolled beam section varies from (A) 1.10 to 1.20 (B) 1.20 to 1.30 (C) 1.30 to 1.40 (D) 1.40 to 1.50

Description : The shape factor of standard rolled beam section varies from  (A) 1.10 to 1.20  (B) 1.20 to 1.30  (C) 1.30 to 1.40  (D) 1.40 to 1.50 

Last Answer : (A) 1.10 to 1.20 

The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option D

The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Description : The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times

Last Answer : Answer: Option C

Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Description : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Last Answer : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two ... 3//4Omega` C. `3Omega` D. `6Omega`

A weir is used to measure the large water discharge rate from a river or from an open channel. A weir is not of __________ shape. (A) Circular (B) Rectangular (C) Triangular (D) Trapezoidal

Description : A weir is used to measure the large water discharge rate from a river or from an open channel. A weir is not of __________ shape. (A) Circular (B) Rectangular (C) Triangular (D) Trapezoidal

Last Answer : (A) Circular

Why the shape of OP-AMP is triangular not other shape?

Description : Why the shape of OP-AMP is triangular not other shape?

Last Answer : Ans-The Triangular shape symbolizes that it works for continous signals and hence forth it is an analog device. ex: Opamp If it is square then it is digital device. ex: Multiplexer If the shape is both triangular and square then it is mixed signal device. ex: ADC DAC

cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Last Answer : ans c

is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board

Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section

Last Answer :   <!-- [endif] -->Knife Section

The cell is usually ____ in shape. • Triangular • Circular • Rectangular • Cylindrical

Description : The cell is usually ____ in shape. • Triangular • Circular • Rectangular • Cylindrical

Last Answer : • Cylindrical

For a beam of triangular cross section, the ratio τmax/ τav is (a) 3/2 (b) 4/2 (c) 5/2 (d) None

Description : For a beam of triangular cross section, the ratio τmax/ τav is (a) 3/2 (b) 4/2 (c) 5/2 (d) None

Last Answer : (a) 3/2

What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Description : What is the shear stress acting along the neutral axis, over a triangular section? a. 2.66 (S/bh) b. 1.5 (S/bh) c. 0.375 (S/bh) d. None of the above

Last Answer : a. 2.66 (S/bh)

Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Description : Moment of Inertia of triangular section about an axis passing through its base is given by a.bh3/12 b.bh3/32 c.bh3/36 d.None of the above e.Tapered bearing

Last Answer : a. bh3/12

A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Last Answer : b) False

A furrow cross-section in a country plough is commonly a) Circular b) Triangular c) Rectangular d) Trapezoidal

Description : A furrow cross-section in a country plough is commonly a) Circular b) Triangular c) Rectangular d) Trapezoidal

Last Answer : ans b

it is a harrow with peg shaped teeth of diamond cross section to a Rectangular frame. A) Spike tooth harrow C Spring tooth harrow B) Acme harrow D Triangular harrow.

Description : it is a harrow with peg shaped teeth of diamond cross section to a Rectangular frame. A) Spike tooth harrow C Spring tooth harrow B) Acme harrow D Triangular harrow.

Last Answer : Spike tooth harrow

Maximum shear stress in a triangular section ABC of height H and base B occurs at _________ a. H b. H/2 c. H/3 d. neutral axis

Description : Maximum shear stress in a triangular section ABC of height H and base B occurs at _________ a. H b. H/2 c. H/3 d. neutral axis

Last Answer : b. H/2

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2

For structural analysis, Maxwell's reciprocal theorem can be applied to: (A) Plastic structures (B) Elastic structures (C) Symmetrical structures (D) All the above

Description : For structural analysis, Maxwell's reciprocal theorem can be applied to: (A) Plastic structures (B) Elastic structures (C) Symmetrical structures (D) All the above

Last Answer : (B) Elastic structures

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

In the virtual work method of plastic analysis of steel structures, the virtual quantity is (a) Slope (b) Moment (c) Load (d) Displacement

Description : In the virtual work method of plastic analysis of steel structures, the virtual quantity is (a) Slope (b) Moment (c) Load (d) Displacement

Last Answer : (d) Displacement

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Description : A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Last Answer : (A) Plastic

In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported I-section beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (D) L/5 

Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment(B) In a loaded beam, the moment at which the entire section of the beam becomes fully plastic, is called plastic moment (C) In a fully plastic stage of the beam, the neutral axis divides the section in two sections of equal area (D) All the above

Description : Pick up the correct statement from the following:  (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of  equal area  (D) All the above 

Last Answer : (D) All the above 

What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Last Answer : (a) Zero

The moment capacity of section at plastic hinge equals a) Yield moment b) Zero c) Fully plastic moment d) Twice the yield moment

Description : The moment capacity of section at plastic hinge equals a) Yield moment b) Zero c) Fully plastic moment d) Twice the yield moment

Last Answer : c) Fully plastic moment

Uniform flow occurs when (A) The flow is steady (B) The flow is streamline (C) Size and shape of the cross section in a particular length remain constant (D) Size and cross section change uniformly along length

Description : Uniform flow occurs when (A) The flow is steady (B) The flow is streamline (C) Size and shape of the cross section in a particular length remain constant (D) Size and cross section change uniformly along length

Last Answer : Answer: Option C

For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Description : For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Last Answer : Answer: Option C

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

An error of 1% in measuring head over the crest of the notch (H) will produce an error of __________ in discharge over a triangular notch, (A) 1 % (B) 1.5 % (C) 2 % (D) 2.5 %

Description : An error of 1% in measuring head over the crest of the notch (H) will produce an error of __________ in discharge over a triangular notch, (A) 1 % (B) 1.5 % (C) 2 % (D) 2.5 %

Last Answer : Answer: Option D

The discharge over a triangular notch is A) Inversely proportional to H 3/2 B) Directly proportional to H 3/2 C) Inversely proportional to H 5/2 D) Directly proportional to H 5/2

Description : The discharge over a triangular notch is A) Inversely proportional to H 3/2 B) Directly proportional to H 3/2 C) Inversely proportional to H 5/2 D) Directly proportional to H 5/2

Last Answer : Answer: Option D

An error of 1% in measuring head over the apex of the notch (H) will produce an error of _________ in discharge over a triangular notch. (A) 1 % (B) 1.5 % (C) 2 % (D) 2.5 %

Description : An error of 1% in measuring head over the apex of the notch (H) will produce an error of _________ in discharge over a triangular notch. (A) 1 % (B) 1.5 % (C) 2 % (D) 2.5 %

Last Answer : Answer: Option D

The error in discharge (dQ/Q) to the error in measurement of head (dH/H) over a triangular notch is given by (A) dQ/Q = 3/2 × (dH/H) (B) dQ/Q = 2 × (dH/H) (C) dQ/Q = 5/2 × (dH/H) (D) dQ/Q = 3 × (dH/H)

Description : The error in discharge (dQ/Q) to the error in measurement of head (dH/H) over a triangular notch is given by (A) dQ/Q = 3/2 × (dH/H) (B) dQ/Q = 2 × (dH/H) (C) dQ/Q = 5/2 × (dH/H) (D) dQ/Q = 3 × (dH/H)

Last Answer : Answer: Option C

Which one of the following statements regarding section 34 and section 149 of Indian Penal Code is correct? a) Common intention and common object are same b) Both are distinct offences in themselves c) Section 34 enunciates a mere principle of liability and creates no offence while section 149 creates a specific offence. d) Section 34 and 149 are mutually halping sections.

Description : Which one of the following statements regarding section 34 and section 149 of  Indian Penal Code is correct? a) Common intention and common object are same b) Both are distinct offences in ... section 149 creates a specific offence. d) Section 34 and 149 are mutually halping sections.

Last Answer : c) Section 34 enunciates a mere principle of liability and creates no offence while  section 149 creates a specific offence.

Which of the following is not an essential element of section 34 of IPC? a) Criminal act done by several persons. b) Criminal act done in furtherance of a common intention c) Pre-arranged plan between persons doing criminal act d) Act done in furtherance of common object.

Description : Which of the following is not an essential element of section 34 of IPC? a) Criminal act done by several persons. b) Criminal act done in furtherance of a common intention c) Pre-arranged plan between persons doing criminal act d) Act done in furtherance of common object.

Last Answer : d) Act done in furtherance of common object.

Section 34 of IPC (a) Creates a substantive offence (b) Is a rule of evidence (c) Both (a) and (b) (d) Neither (a) nor (b).

Description : Section 34 of IPC (a) Creates a substantive offence (b) Is a rule of evidence (c) Both (a) and (b) (d) Neither (a) nor (b).

Last Answer : (d) Neither (a) nor (b

To establish section 34 of IPC (a) Common intention be proved but not overt act be proved (b) Common intention and overt act both be proved (c) Common intention need not be proved but overt act be proved (d) All the above.

Description : To establish section 34 of IPC (a) Common intention be proved but not overt act be proved (b) Common intention and overt act both be proved (c) Common intention need not be proved but overt act be proved (d) All the above.

Last Answer : (d) All the above.

Transmission by post of value-payable postal articles explained in a) Section 34 b) Section 33 c) Section 20 d) None of these

Description : Transmission by post of value-payable postal articles explained in a) Section 34 b) Section 33 c) Section 20 d) None of these

Last Answer : a) Section 34