The R.L. of ground water table on the sides of a valley is 1505 m whereas R.L. of the stream water is 1475 m. If 60° slope consists of pervious soil between R.L. 1485 m to 1500 m, the gravity spring may be expected at the point of reduced level (A) 1500 m (B) 1505 m (C) 1475 m (D) 1485 m

The R.L. of ground water table on the sides of a valley is 1505 m whereas R.L. of the stream water 

is 1475 m. If 60° slope consists of pervious soil between R.L. 1485 m to 1500 m, the gravity spring 

may be expected at the point of reduced level 

(A) 1500 m 

(B) 1505 m 

(C) 1475 m 

(D) 1485 m 

by

1 Answer

Answer :

(D) 1485 m 

by

Related questions

If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2(D) D/6m(h1 - h2)3

Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3

Last Answer : (C) D/6m(h1 - h2)2

The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is (A) 502.685 m (B) 501.345 m (C) 501.340 m (D) 504.030 m

Description : The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is (A) 502.685 m (B) 501.345 m (C) 501.340 m (D) 504.030 m

Last Answer : (C) 501.340 m

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

Pick up the correct statement from the following: (A) If ground water enters the channel, the channel is known as effluent channel (B) If water goes out of channel to meet ground water, the channel is said to be influent stream (C) If the water table is at higher level than the water level in channel, ground water flows to the stream (D) All the above

Description : Pick up the correct statement from the following: (A) If ground water enters the channel, the channel is known as effluent channel (B) If water goes out of channel to meet ground water, the channel ... level than the water level in channel, ground water flows to the stream (D) All the above

Last Answer : Answer: Option D

A satellite receives an uplink frequency of _______ MHz from a ground station of 3700 MHz. A. 8150 MHz B. 1475 MHz C. 2225 MHz D. 5925 MHz

Description : A satellite receives an uplink frequency of _______ MHz from a ground station of 3700 MHz. A. 8150 MHz B. 1475 MHz C. 2225 MHz D. 5925 MHz

Last Answer : D. 5925 MHz

The shadow of a tower standing on level ground is found to be 40 m longer when the Sun’s altitude is 30° than when it is 60°. Find the height of the tower. -Maths 9th

Description : The shadow of a tower standing on level ground is found to be 40 m longer when the Sun’s altitude is 30° than when it is 60°. Find the height of the tower. -Maths 9th

Last Answer : this is the answer

A strainer type well sunk through three previous layers intervened by three impervious aquicludes, draws water from (A) Top most pervious layer (B) Central pervious layer (C) Lowest pervious layer (D) All the pervious layer

Description : A strainer type well sunk through three previous layers intervened by three impervious aquicludes, draws water from (A) Top most pervious layer (B) Central pervious layer (C) Lowest pervious layer (D) All the pervious layer

Last Answer : (D) All the pervious layers

The total weight of a pycnometer with water and oven dried soil 20 (g) is 1600 g. The pycnometer filled with water alone weighs 1500 g. The specific gravity of the soil, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 2.5

Description : The total weight of a pycnometer with water and oven dried soil 20 (g) is 1600 g. The pycnometer filled with water alone weighs 1500 g. The specific gravity of the soil, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 2.5

Last Answer : (C) 2.0

A plane inclined at an angle to the horizontal at which the soil is expected to stay in the absence of any lateral support, is known as (A) Natural slope line (B) Repose line (C) The line (D) All the above

Description : A plane inclined at an angle to the horizontal at which the soil is expected to stay in the absence of any lateral support, is known as (A) Natural slope line (B) Repose line (C) The line (D) All the above

Last Answer : Answer: Option D

If the formation level of a highway has a uniform gradient for a particular length, and the ground is also having a longitudinal slope, the earthwork may be calculated by (A) Mid-section formula (B) Trapezoidal formula (C) Prismoidal formula (D) All the above

Description : If the formation level of a highway has a uniform gradient for a particular length, and the ground is also having a longitudinal slope, the earthwork may be calculated by (A) Mid-section formula (B) Trapezoidal formula (C) Prismoidal formula (D) All the above

Last Answer : (D) All the above

A rectangular tank 10 m x 5 m in plan and 3 m deep is divided by a partition wall parallel to the shorter wall of the tank. One of the compartments contains water to a depth of 3 m, and the other a lighter liquid of specific gravity 0.75 to a depth of 2 m. The resultant pressure thrust on the partition wall is (a) 1000 kg (b) 1500 kg (c) 2000 kg (d) 2500 kg

Description : A rectangular tank 10 m x 5 m in plan and 3 m deep is divided by a partition wall parallel to the shorter wall of the tank. One of the compartments contains water to a depth of 3 m, and the other a lighter ... pressure thrust on the partition wall is (a) 1000 kg (b) 1500 kg (c) 2000 kg (d) 2500 kg

Last Answer : Correct Answer is 15000 kg

If whole circle bearing of a line is 120°, its reduced bearing is (A) S 20° E (B) S 60° E (C) N 120° E (D) N 60° E

Description : If whole circle bearing of a line is 120°, its reduced bearing is  (A) S 20° E (B) S 60° E (C) N 120° E (D) N 60° E

Last Answer : (B) S 60° E

A counter may be defined as an imaginary line passing through (a) Points on the longitudinal section (b) Points of equal elevation (c) Point of equal local ground slope (d) Points of transverse section surveys

Description : A counter may be defined as an imaginary line passing through (a) Points on the longitudinal section (b) Points of equal elevation (c) Point of equal local ground slope (d) Points of transverse section surveys

Last Answer : (b) Points of equal elevation

If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Description : If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Last Answer : (A) L/G

Water may not contain much impurity if its source is (A) Reservoirs (B) Stream flowing in plains (C) Lakes in lower regions (D) Spring along hill slopes

Description : Water may not contain much impurity if its source is  (A) Reservoirs  (B) Stream flowing in plains  (C) Lakes in lower regions  (D) Spring along hill slopes

Last Answer : (D) Spring along hill slopes

On an open ground, a biker follows a track that turns to his left by an angle of 60° after every 600 m. Starting from a given turn

Description : On an open ground, a biker follows a track that turns to his left by an angle of 60° after every 600 m. Starting from a given turn

Last Answer : On an open ground, a biker follows a track that turns to his left by an angle of 60° after ... total path length covered by the motorist in each case.

Field capacity represents the maximum quantity of water held: w) in the soil against the force of gravity x) in the ground water zone y) in the intermediate zone z) below the water table

Description : Field capacity represents the maximum quantity of water held: w) in the soil against the force of gravity x) in the ground water zone y) in the intermediate zone z) below the water table

Last Answer : ANSWER: W -- IN THE SOIL AGAINST THE FORCE OF GRAVITY

If is the difference in level between end points separated by , then the slope correction is [(h²/2l) + (h 4 /8l3 )]. The second term may be neglected if the value of in a 20 m distance is less than (A) ½ m (B) 1 m (C) 2 m (D) 3 m

Description : If is the difference in level between end points separated by , then the slope correction is [(h²/2l) + (h 4 /8l3 )]. The second term may be neglected if the value of in a 20 m distance is less than (A) ½ m (B) 1 m (C) 2 m (D) 3 m

Last Answer : (D) 3 m

If the maximum spring rise is 2 m and height of the waves expected is 4 m , then the breakwater height above the datum will be (A) 2.5 m (B) 4 m (C) 5 m (D) 7

Description : If the maximum spring rise is 2 m and height of the waves expected is 4 m , then the breakwater height above the datum will be (A) 2.5 m (B) 4 m (C) 5 m (D) 7

Last Answer : (D) 7

Higher yield may be expected from (A) Gravity springs (B) Surface springs (C) Artesian springs (D) All the above

Description : Higher yield may be expected from (A) Gravity springs (B) Surface springs (C) Artesian springs (D) All the above

Last Answer : (C) Artesian springs

In gravity canals, F.S.L. is a. Always at the ground level b. Always below the ground level c. Generally 4 to 5 meters above the ground level d. Only a few cm above the ground level

Description : In gravity canals, F.S.L. is a. Always at the ground level b. Always below the ground level c. Generally 4 to 5 meters above the ground level d. Only a few cm above the ground level

Last Answer : d. Only a few cm above the ground level

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

If the water table rises upto ground surface, then the (A) Effective stress is reduced due to decrease in total stress only but pore water pressure does not change (B) Effective stress is reduced due to increase in pore water pressure only but total stress does not change (C) Total stress is reduced due to increase in pore water pressure only but effective stress does not change (D) Total stress is increased due to decrease in pore water pressure but effective stress does not change

Description : If the water table rises upto ground surface, then the (A) Effective stress is reduced due to decrease in total stress only but pore water pressure does not change (B) Effective stress is ... D) Total stress is increased due to decrease in pore water pressure but effective stress does not change

Last Answer : (B) Effective stress is reduced due to increase in pore water pressure only but total stress does not change

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

In a 2-mass 3 spring vibrating system the two masses each are of 9.8 kg coupling spring is having a stiffness of 3430 N/m whereas the other two springs have each a stiffness of 8820 N/m. The two natural frequencies in rad /sec are A) 10 & 20 B) 20 & 30 C) 30 & 40D) 40 & 50

Description : In a 2-mass 3 spring vibrating system the two masses each are of 9.8 kg coupling spring is having a stiffness of 3430 N/m whereas the other two springs have each a stiffness of 8820 N/m. The two natural frequencies in rad /sec are A) 10 & 20 B) 20 & 30 C) 30 & 40D) 40 & 50

Last Answer : C) 30 & 40

Tank irrigation is not popular in North India because, A. There are perennial rivers. B. Land is not undulating. C. The surface there is pervious and cannot collect water effectively. D. All the above.

Description : Tank irrigation is not popular in North India because, A. There are perennial rivers. B. Land is not undulating. C. The surface there is pervious and cannot collect water effectively. D. All the above.

Last Answer : D. All the above.

The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope of the arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E

Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with  a uniformly distributed load l t per horizontal length is (where Ic  is the M.I. at the crown, which  varies as the slope ... arch).  (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E

Last Answer : (D) 200/E

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m.

Description : A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m. If motor is connected to single phase semiconverter with the same firing angle of 60°, it would run at (a) 2000 rpm (b) 1850 rpm (c) 1500 rpm (d) 1000 rpm 

Last Answer : Ans =1500

To determine the discharge at a section in a stream from its rating curve, the required data are (i) Slope of water surface at the section (ii) Stage at the section (ii) Current meter readings at the section The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) Only (ii) (D) Only (iii)

Description : To determine the discharge at a section in a stream from its rating curve, the required data are (i) Slope of water surface at the section (ii) Stage at the section (ii) Current meter readings at the section The correct ... ) (i) and (ii) (B) (ii) and (iii) (C) Only (ii) (D) Only (iii)

Last Answer : Answer: Option C

If the long chord and tangent length of a circular curve of radius R are equal the angle of deflection, is (A) 30° (B) 60° (C) 90° (D) 120°

Description : If the long chord and tangent length of a circular curve of radius R are equal the angle of deflection, is (A) 30° (B) 60° (C) 90° (D) 120°

Last Answer : D

Michael Angelo was born this day in 1475. Of all his works, which do you like best and why?

Description : Michael Angelo was born this day in 1475. Of all his works, which do you like best and why?

Last Answer : This says it all Exquisite and stunning from all imaginable elements of man’s ability to create, express and communicate emotion at an incomparable level.

Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m

Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the  sight on the down-slope, must be less than  (A) 30 m  (B) 25 m  (C) 20 m  (D) 15 m 

Last Answer : (B) 25 m 

The slope correction may be ignored if (A) The slope of the ground is less than 3° (B) To slope of the ground is say 1 in 19 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The slope correction may be ignored if  (A) The slope of the ground is less than 3°  (B) To slope of the ground is say 1 in 19  (C) Both (a) and (b)  (D) Neither (a) nor (b) 

Last Answer : (C) Both (a) and (b

The total pressure on the surface of a vertical sluice gate 2 m x 1 m with its top 2 m surface being 0.5 m below the water level will be (A) 500 kg (B) 1000 kg (C) 1500 kg (D) 2000 kg

Description : The total pressure on the surface of a vertical sluice gate 2 m x 1 m with its top 2 m surface being 0.5 m below the water level will be (A) 500 kg (B) 1000 kg (C) 1500 kg (D) 2000 kg

Last Answer : Answer: Option D

A man takes 10 hours to cover a distance while traveling upstream on a boat, whereas while traveling downstream it takes 6 hours. If the speed of the boat in still water is 6 kmph, what is the speed of the stream? 1 : 2.5 kmph 2 : 2.2 kmph 3 : 2 kmph 4 : 1.5 kmph 5 : None of these

Description : A man takes 10 hours to cover a distance while traveling upstream on a boat, whereas while traveling downstream it takes 6 hours. If the speed of the boat in still water is 6 kmph, what is the speed of the stream? 1 : 2.5 kmph 2 : 2.2 kmph 3 : 2 kmph 4 : 1.5 kmph 5 : None of these

Last Answer : 4 : 1.5 kmph

The two sides of a tringle are increasing at the rate of 1/2 ft/sec with their included angle decreasing at the rate of π/90 rad/sec. What is the rate of change of area when the sides and the included angle are respectively 5 ft,8 ft, and 60°?

Description : The two sides of a tringle are increasing at the rate of 1/2 ft/sec with their included angle decreasing at the rate of π/90 rad/sec. What is the rate of change of area when the sides and the included angle are respectively 5 ft,8 ft, and 60°?

Last Answer : Area = (L1 L2) sin(angle) , where L1, L2 and and angle are functions of time t. Take the derivative using the multiplication rule. The derivative will equal (L1L2)(derivative of sin) + sin times ... will have to use the multiplication rule a second time to get the derivative of L1 L2. Good luck.

The adjacent sides of a parallelogram are 2a and a. If the angle between them is 60°, then one of the diagonals of the parallelogram is -Maths 9th

Description : The adjacent sides of a parallelogram are 2a and a. If the angle between them is 60°, then one of the diagonals of the parallelogram is -Maths 9th

Last Answer : answer:

It consists of dropping the seeds in furrow lines in a continuous stream and covering them with soil. The spacing between the seeds is not uniform. a. Dibbing c. Broadcasting d. None of the above.

Description : It consists of dropping the seeds in furrow lines in a continuous stream and covering them with soil. The spacing between the seeds is not uniform. a. Dibbing c. Broadcasting d. None of the above.

Last Answer : Ans - b. Drilling

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Last Answer : B 600 N/m

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they are connected in series, what will be the equivalent spring stiffness? A 1KN/m B 600 N/m C 1 N/m D 600 KN/m

Last Answer : B 600 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A. 3500 N/m B. 1166 N/mC. 857.63 N/m D. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A. 3500 N/m B. 1166 N/mC. 857.63 N/m D. None of the above

Last Answer : C. 857.63 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A) 3500 N/m B) 1166 N/m C) 857.63 N/m D) None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m A) 3500 N/m B) 1166 N/m C) 857.63 N/m D) None of the above

Last Answer : C) 857.63 N/m

Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they B are connected in series, what will be the equivalent spring stiffness? (A) 1KN/m (B) 600 N/m (C) 1 N/m (D) 600 KN/m

Description : Two springs have spring stiffness of 1500 N/m and 1 KN/m respectively. If they B are connected in series, what will be the equivalent spring stiffness? (A) 1KN/m (B) 600 N/m (C) 1 N/m (D) 600 KN/m

Last Answer : (B) 600 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Last Answer : c. 857.63 N/m

Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Description : Two springs have spring stiffness of 1500 N/m and 2000 N/m respectively. If they are connected in series, what is the spring stiffness if they are replaced by an equivalent system.3500 N/m a. 3500 N/m b. 1166 N/m c. 857.63 N/m d. None of the above

Last Answer : c. 857.63

The bearing of C from A is N 30° E and from B, 50 metres east of A, is N 60° W. The departure of C from A is (A) 50 m (B) 50 m (C) 25 m (D) 25 m

Description : The bearing of C from A is N 30° E and from B, 50 metres east of A, is N 60° W. The departure of C from A is (A) 50 m (B) 50 m (C) 25 m (D) 25 m

Last Answer : (D) 25 m