Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/cm2 (C) The water at pressure 1 to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these

Pick up the incorrect statement from the following regarding fire hydrants
(A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire
(B) The minimum water pressure hydrants, is kept 1.5 kg/cm2
(C) The water at pressure 1 to 1.5 kg/cm2
 is made available for 4 to 5 hours for constant use
(D) None of these
by

1 Answer

Answer :

(D) None of these
by

Related questions

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

According to National Building Code, the hydrants in water mains is provided at minimum interval of (A) 50 m (B) 60 m (C) 75 m (D) 90 m

Description : According to National Building Code, the hydrants in water mains is provided at minimum interval of (A) 50 m (B) 60 m (C) 75 m (D) 90 m

Last Answer :  Option C

Pick up the incorrect statement regarding a master trap from the following: (A) It is provided in between the lower end of the house drain and the street sewer (B) It is provided a cleaning eye at the top of the trap (C) The mica flap valve which opens inwards only, is fitted at the top of the inlet pipe (D) The water seal is less than that of ordinary traps

Description : Pick up the incorrect statement regarding a master trap from the following: (A) It is provided in between the lower end of the house drain and the street sewer (B) It is provided a cleaning eye at the ... fitted at the top of the inlet pipe (D) The water seal is less than that of ordinary traps

Last Answer : (D) The water seal is less than that of ordinary traps

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : (C) 200 kg/cm2

Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2

Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2

Last Answer : (D) 300 kg/cm2

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm

Description : The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm

Last Answer : Answer: Option D

In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2

Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2

Last Answer : (A) 100 kg/cm2

For M 150 mix concrete, according to I.S. specifications, local bond stress, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Description : For M 150 mix concrete, according to I.S. specifications, local bond stress, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option B

According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option A

The live load to be considered for an inaccessible roof, is (A) Nil (B) 75 kg/m2 (C) 150 kg/cm2 (D) 200 kg/m

Description : The live load to be considered for an inaccessible roof, is (A) Nil (B) 75 kg/m2 (C) 150 kg/cm2 (D) 200 kg/m

Last Answer : Answer: Option B

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2

Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2

Last Answer : : Option B

Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Description : Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Last Answer : (D) All the above

Distribution mains of any water supply, is normally designed for its average daily requirement (A) 100 %(B) 150 % (C) 200 % (D) 225 %

Description : Distribution mains of any water supply, is normally designed for its average daily requirement  (A) 100 % . (B) 150 %  (C) 200 %  (D) 225 %

Last Answer : (D) 225 %

Water supply includes (A) Collection, transportation and treatment of water (B) Distribution of water to consumers (C) Provision of hydrants for fire fighting (D) All the above

Description : Water supply includes  (A) Collection, transportation and treatment of water  (B) Distribution of water to consumers  (C) Provision of hydrants for fire fighting  (D) All the above 

Last Answer : (D) All the above 

The minimum compressive strength of 1st class bricks should be (A) 75 kg/cm2 (B) 90 kg/cm2 (C) 100 kg/cm2 (D) 120 kg/cm2

Description : The minimum compressive strength of 1st class bricks should be (A) 75 kg/cm2 (B) 90 kg/cm2 (C) 100 kg/cm2 (D) 120 kg/cm2

Last Answer : Answer: Option C

The minimum compressive strength of 2nd class bricks should be (A) 75 kg/cm2 (B) 90 kg/cm2 (C) 100 kg/cm2 (D) 120 kg/cm

Description : The minimum compressive strength of 2nd class bricks should be (A) 75 kg/cm2 (B) 90 kg/cm2 (C) 100 kg/cm2 (D) 120 kg/cm

Last Answer : Answer: Option A

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Last Answer : (D) None of these

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2

Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2

Last Answer : Answer: Option D

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg

Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a  concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2  and fs= 10 kg/cm2  the safe  load is  (A) 3025 kg  (B) 3050 kg  (C) 3075 kg  (D) 3100 kg 

Last Answer : (C) 3075 kg 

Pickup the incorrect statement from the following: (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line (B) The pressure conduits may be taken uphill upto a maximum height of 8.3 m (C) Aqueducts and tunnels sections are generally kept circular (D) None of these

Description : Pickup the incorrect statement from the following:  (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line  (B) The pressure conduits may be taken uphill ... m  (C) Aqueducts and tunnels sections are generally kept circular  (D) None of these 

Last Answer : (D) None of these 

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) Cement should be mixed by hand in order to maintain uniformity (C) Concrete mix should be stored in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° ± 2°C

Description : Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) ... in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° 2°C

Last Answer : Answer: Option D

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

Pressure of compressed air is kept during preheating by CAPS? (i) 1 to 2 kg/cm2 (ii) .1 to .2 kg/cm2 (iii) 2 to 3 kg/cm2 (iv) 0.2 to 0.3 kg/cm2*

Description : Pressure of compressed air is kept during preheating by CAPS? (i) 1 to 2 kg/cm2 (ii) .1 to .2 kg/cm2 (iii) 2 to 3 kg/cm2 (iv) 0.2 to 0.3 kg/cm2*

Last Answer : (iv) 0.2 to 0.3 kg/cm2*

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

Mark the incorrect statement: (A) Mail bags intended for dispatch during working hours of the day should be secured by the mail assistant in the mail box (B) The forward bags should be kept locked up in the mail box until it is time to dispatch them (C) Parcel received loose should be made over to Parcel Assistant under receipt (D) BO bags and loose account bags should be transferred to Sub Account Assistant

Description : Mark the incorrect statement: (A) Mail bags intended for dispatch during working hours of the day should be secured by the mail assistant in the mail box (B) The forward bags should be ... Assistant under receipt (D) BO bags and loose account bags should be transferred to Sub Account Assistant

Last Answer : (D) BO bags and loose account bags should be transferred to Sub Account Assistan

A fire tube boiler is limited to a maximum steam pressure of about __________ kg/cm2. (A) 6 (B) 18 (C) 38 (D) 52

Description : A fire tube boiler is limited to a maximum steam pressure of about __________ kg/cm2. (A) 6 (B) 18 (C) 38 (D) 52

Last Answer : (B) 18

Where have all the fire hydrants gone?

Description : Where have all the fire hydrants gone?

Last Answer : I have a yellow one in my yard. My house insurance was discounted because of that.

Are there any differences between fire hydrants and fire department connections?

Description : Are there any differences between fire hydrants and fire department connections?

Last Answer : Fire hydrants are essential when it comes to putting out fire by the fire department. Fire hydrants are connected to a large water supply through underground pipes. When firefighters arrive on the scene, ... , it opens a valve deep underground that allows water to start to flow into the hydrant.

Plywood is obtained by gluing wooden sheets at (A) 100 to 150 N/cm2 (B) 100 to 130°C (C) Both (A) and (B) (D) Neither (A) n

Description : Plywood is obtained by gluing wooden sheets at (A) 100 to 150 N/cm2 (B) 100 to 130°C (C) Both (A) and (B) (D) Neither (A) nor (b)

Last Answer : Answer: Option C

Minimum number of 50 kg cement bags per cubic metre of concrete for a mix corresponding to crushing strength 280 kg/cm2 at 28 days, are (A) 5.0 (B) 6.5(C) 7.0 (D) 7.5

Description : Minimum number of 50 kg cement bags per cubic metre of concrete for a mix corresponding to crushing strength 280 kg/cm2 at 28 days, are (A) 5.0 (B) 6.5 (C) 7.0 (D) 7.5

Last Answer : Answer: Option B

The minimum quantity of cement to be used in controlled concrete is (a) 120kg/cm2 (b) 160 kg/cm2 (c) 220 kg/cm2 (d) 280 kg/cm2

Description : The minimum quantity of cement to be used in controlled concrete is (a) 120kg/cm2 (b) 160 kg/cm2 (c) 220 kg/cm2 (d) 280 kg/cm2

Last Answer : (c) 220 kg/cm2

Pick up the incorrect statement from the following: In a dry dock block made of hard wood, (A) Spacing of the blocks is 1.35 m (B) The lowest block is 1.8 m long 40 cm × 40 cm in cross-section (C) The middle block is 1.6 m long 40 cm × 40 cm in cross-section (D) None of these

Description : Pick up the incorrect statement from the following: In a dry dock block made of hard wood, (A) Spacing of the blocks is 1.35 m (B) The lowest block is 1.8 m long 40 cm × 40 cm in cross-section (C) The middle block is 1.6 m long 40 cm × 40 cm in cross-section (D) None of these

Last Answer : (D) None of these

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/cm2 Answer: Option

Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at  the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:  (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c

Last Answer : (A) 960 kg/cm

a tacheometer is fitted with an anal-latic lens (A) Additive constant is 100, multiplying constant is zero (B) Multiplying constant is 100, additive constant is zero (C) Both multiplying and additive constants are 100 (D) Both multiplying and additive constants are 50

Description : a tacheometer is fitted with an anal-latic lens (A) Additive constant is 100, multiplying constant is zero (B) Multiplying constant is 100, additive constant is zero (C) Both multiplying and additive constants are 100 (D) Both multiplying and additive constants are 50

Last Answer : (B) Multiplying constant is 100, additive constant is zero

The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2(D) 400 kg/cm2

Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the  point is:  (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2

Last Answer : (A) 100 kg/cm2

If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Last Answer : (B) 250 kg

An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm

Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm

Last Answer : Answer: Option D

The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear(D) Needs redesigning

Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning

Last Answer : Answer: Option B

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D