Description : The minimum compressive strength of 2nd class bricks should be (A) 75 kg/cm2 (B) 90 kg/cm2 (C) 100 kg/cm2 (D) 120 kg/cm
Last Answer : Answer: Option A
Description : he minimum compressive strength of first class brick should be a) 75 kg per centimeter square b) 90 kg per centimeter square c) 100 kg per centimeter square* d) 120 kg per centimeter square
Last Answer : c) 100 kg per centimeter square*
Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Last Answer : (C) 200 kg/cm2
Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2
Last Answer : (D) 300 kg/cm2
Last Answer : Answer: Option C
Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Description : The preliminary test is repeated if the difference of compressive strength of three test specimens, exceeds (A) 5 kg/cm2 (B) 8 kg/cm2 (C) 10 kg/cm2 (D) 15 kg/cm2
Last Answer : Answer: Option D
Description : If the average compressive strength is 4000 kg/cm2 and standard deviation is 500, the co-efficient of variation is (A) 10 % (B) 12.5 % (C) 15 % (D) 18.5%
Last Answer : Answer: Option B
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm
Description : The minimum cube strength of concrete used for a pre-stressed member, is (A) 50 kg/cm2 (B) 150 kg/cm2 (C) 250 kg/cm2 (D) 350 kg/cm
Description : Minimum number of 50 kg cement bags per cubic metre of concrete for a mix corresponding to crushing strength 280 kg/cm2 at 28 days, are (A) 5.0 (B) 6.5 (C) 7.0 (D) 7.5
Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm
Last Answer : (D) 8 cm
Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive
Last Answer : (C) 26.67 kg/cm2 tensile
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Description : Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/ ... to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these
Last Answer : (D) None of these
Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2
Last Answer : : Option B
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : In India, which one of the following should be considered the right combination of the age in days and live body weight in kg for a lamb for its weaning ? (A) 20 days to 30 days and 6 kg to 7 kg (B) 45 days to 60 ... (D) 75 days to 90 days and 12 kg to 15 kg (E) 55 days to 70 days and 9 kg to 11 kg
Last Answer : (C) 105 days to 120 days and 18 kg to 21 kg
Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm
Last Answer : (B) 75 mm
Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm
Last Answer : (a) 120 mm
Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg
Last Answer : (C) 3075 kg
Description : The live load to be considered for an inaccessible roof, is (A) Nil (B) 75 kg/m2 (C) 150 kg/cm2 (D) 200 kg/m
Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm
Last Answer : b) 5 cm
Description : The compressive strength of cement should not be less than about 110Kg/cm2 after three days & not less than 170Kg/cm2 after seven days. The fineness of an ordinary cement as determined by turbidimetric method should be about __________ cm2 /gm. (A) 800 (B) 1600 (C) 4000 (D) 8500
Last Answer : (B) 1600
Description : The 28 days cube strength of mass concrete using aggregates of maximum size 5 cm for gravity dams should be (A) Between 150 to 300 kg/cm2 (B) Between 350 to 600 kg/cm2 (C) Between 150 to 500 kg/cm2 (D) Below 200 kg/cm2
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : The minimum quantity of cement to be used in controlled concrete is (a) 120kg/cm2 (b) 160 kg/cm2 (c) 220 kg/cm2 (d) 280 kg/cm2
Last Answer : (c) 220 kg/cm2
Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2
Last Answer : [ B ] 11.5 N/mm2
Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300
Last Answer : (B) 1 and 200
Description : The injection pressure of ic engine used on tractors is in range of kg/cm2 1. 0-6 2. 60-120 3. 120-200 4. 200-300
Last Answer : ans 3
Description : n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In each batch about 120 ... dryer and the dryer efficiency is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.
Last Answer : Given that Qty of material dried per batch - 120 Kgs Moisture at inlet - 60% a. The quantity of moisture removed per batch. Water quantity in a wet batch - 120 x 0.6 = 72 Kgs. Quantity of bone dry ... - 48/0.95 = 50.5 Kgs. Equivalent water in a dry batch - 50.5 - 48 = 2.5 Kgs.
Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is: (A) 960 kg/cm2 (B) 980 kg/cm2 (C) 1000 kg/cm2 (D) 1200 kg/c
Last Answer : (A) 960 kg/cm
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg
Last Answer : (B) 250 kg
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Description : fter getting minimum subscription of shares, the company has to allot shares with in--------- ------days. A. 90 B. 100 C. 110 D. 120
Last Answer : D. 120
Description : The fuel in diesel engine is normally injected at pressure of a. 5-10 kg/cm2 b. 20-25 kg/cm2 c 60-80 kg/cm2 d. 90-130 kg/cm2
Last Answer : ANSWER d. 90-130 kg/cm2
Description : The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above
Description : For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm
Last Answer : B
Description : A tank internally measuring 150 cm × 120 cm × 100 cm has 1281600 cm^3 of water in it. Porous bricks are placed in the water until the tank -Maths 9th
Last Answer : Volume of a brick = 20 cm 6 cm 4 cm = 480 cm3. Water absorbed by one brick = (110 480)(110 480) cm3 = 48 cm3. Let x bricks be placed in the water. Then, x bricks absorb 48x cm3 of water. ... tank ⇒ 1281600 + 480xx - 48xx = 150 x 120 x 100 ⇒ 432xx = 1800000 - 1281600 = 518400 ⇒ xx = 1200.
Description : High strength of concrete requires a water cement ratio of [ A ] 0.10 to 0.15 [ B ] 0.25 to 0.30 [ C ] 0.45 to 0.60 [ D ] 0.75 to 0.90
Last Answer : [ B ] 0.25 to 0.30
Description : On the recommendations of Nagpur Conference, the minimum width of a village road may be (A) 2.45 m (B) 2.75 m (C) 3.66 m (D) 4.90 m
Description : The minimum width of a septic tank is taken (A) 70 cm (B) 75 cm (C) 80 cm (D) 90 c
Last Answer : (B) 75 cm
Description : According to National Building Code, the hydrants in water mains is provided at minimum interval of (A) 50 m (B) 60 m (C) 75 m (D) 90 m
Last Answer : Option C