a tacheometer is fitted with an anal-latic lens (A) Additive constant is 100, multiplying constant is zero (B) Multiplying constant is 100, additive constant is zero (C) Both multiplying and additive constants are 100 (D) Both multiplying and additive constants are 50

a tacheometer is fitted with an anal-latic lens
(A) Additive constant is 100, multiplying constant is zero
(B) Multiplying constant is 100, additive constant is zero
(C) Both multiplying and additive constants are 100
(D) Both multiplying and additive constants are 50
by

1 Answer

Answer :

(B) Multiplying constant is 100, additive constant is zero
by

Related questions

One of the tacheometric constants is additive, the other constant, is (A) Subtractive constant (B) Multiplying constant (C) Dividing constant (D) Indicative constant

Description : One of the tacheometric constants is additive, the other constant, is  (A) Subtractive constant  (B) Multiplying constant  (C) Dividing constant  (D) Indicative constant 

Last Answer : (B) Multiplying constant 

For a tachometer the additive and multiplying constants are respectively (A) 0 and 100 (B) 100 and 0 (C) 0 and 0 (D) 100 and 100

Description : For a tachometer the additive and multiplying constants are respectively (A) 0 and 100 (B) 100 and 0 (C) 0 and 0 (D) 100 and 100

Last Answer : (A) 0 and 100

What are the additive and multiplying constants of planimeter?

Description : What are the additive and multiplying constants of planimeter?

Last Answer : Area of the irregular figure measured by planimeter is given by:  Where M = Multiplying constant  C = Additive costant Multiplying Constant: It is the multiplier whose value is marked on ... It is taken in to consideration only when anchor point is inside the figure, else it is zero.

Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/cm2 (C) The water at pressure 1 to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these

Description : Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/ ... to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these

Last Answer : (D) None of these

How would you determine the constant of given tacheometer on field?

Description : How would you determine the constant of given tacheometer on field? 

Last Answer : Method of determining tacheometric constants in the field1) A fairly level ground is selected. The tacheometer is set up at O. Vertical angle is kept zero and pegs are fixed at A, B & C, known distances apart. ... Average of (f/i) and of (f+d) as obtained above, gives values of constants.

The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Description : The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Last Answer : (B) Telescopic alidade

If is the stadia distance, is the focal length and is the distance between the objective and vertical axis of the techeometer, the multiplying constant, is (A) f/i (B) i/f (C) (f + d) (D) f/d

Description : If is the stadia distance, is the focal length and is the distance between the objective and vertical axis of the techeometer, the multiplying constant, is (A) f/i (B) i/f (C) (f + d) (D) f/d

Last Answer : (A) f/i

An essential agent for converting glucose to glycogen in liver is (A) Latic acid (B) GTP (C) UTP (D) Pyruvic acid

Description : An essential agent for converting glucose to glycogen in liver is (A) Latic acid (B) GTP (C) UTP (D) Pyruvic acid

Last Answer : Answer : C

If the focal length of the object glass is 25 cm and the distance from object glass to the trunnion axis is 15 cm, the additive constant (A) 0.1 (B) 0.4 (C) 0.6 (D) 1.33

Description : If the focal length of the object glass is 25 cm and the distance from object glass to the trunnion axis is 15 cm, the additive constant (A) 0.1 (B) 0.4 (C) 0.6 (D) 1.33

Last Answer : (B) 0.4

Best site where intraocular lens is fitted: a. Capsular ligament b. Endosulcus c. Ciliary supported d. Capsular bag

Description : Best site where intraocular lens is fitted: a. Capsular ligament b. Endosulcus c. Ciliary supported d. Capsular bag

Last Answer : ANSWER: D

Diopter is the power of a lens having a focal length of (A) 25 cm (B) 50 cm (C) 75 cm (D) 100 cm

Description : Diopter is the power of a lens having a focal length of (A) 25 cm (B) 50 cm (C) 75 cm (D) 100 cm

Last Answer : (D) 100 cm

Curl of gradient of a vector is a) Unity b) Zero c) Null vector d) Depends on the constants of the vector

Description : Curl of gradient of a vector is a) Unity b) Zero c) Null vector d) Depends on the constants of the vector

Last Answer : c) Null vector

Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Description : Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Last Answer : (e) None of them*

List any four essential characters of Tacheometer.

Description : List any four essential characters of Tacheometer. 

Last Answer : 1. The value of constant f/i = 100 Where, f = focal length i = length of image. 2. The telescope should be powerful, the magnification should be 20 to 30 times the diameter  3. The ... aperture of the objective should be 35 to 45mm in diameter in order to have a sufficiently bright image.

Define tacheometer. State essential characteristics of tacheometer.

Description : Define tacheometer. State essential characteristics of tacheometer.

Last Answer : Tacheometer A tacheometer is essentially a transit theodolite having a stadia diaphragm. The diaphragm is equipped with two horizontal hairs called stadia hairs in addition to the regular cross hairs. ... The vision through the telescope should give a clear and bright image for a long distance.

What is the difference between a theodolite and a tacheometer. Give any two characteristics of tacheometer.

Description : What is the difference between a theodolite and a tacheometer. Give any two characteristics of tacheometer.

Last Answer : Difference between theodolite and tacheometer. Sr.No Theodolite Tacheometer 1 It is most accurate instrument use for measurement of horizontal and vertical angle. ... 4. The vision through the telescope should give a clear and bright image for a long distance. 

At a given value of E/R (ratio of activation energy and gas constant), the ratio of the rate constants at 500°K and 400°K is 2, if Arrhenius law is used. What will be this ratio, if transition state theory is used with the same value of ‘E/R’? (A) 1.6 (B) 2 (C) 2.24 (D) 2.5

Description : At a given value of E/R (ratio of activation energy and gas constant), the ratio of the rate constants at 500°K and 400°K is 2, if Arrhenius law is used. What will be this ratio, if transition state theory is used with the same value of ‘E/R’? (A) 1.6 (B) 2 (C) 2.24 (D) 2.5

Last Answer : (D) 2.5

The rate expression for a heterogeneous catalytic reaction is given by, - rA = K.KA PA(1 + KA.PA + KR.PR), where K is surface reaction rate constant and KA and KR are absorption equilibrium constants of A and R respectively. If KR PR >> (1 + KA PA), the apparent activation energy EA is equal to (given E is the activation energy for the reaction and ΔHR and ΔHA are the activation energies of adsorption of R and A) (A) E (B) E + ΔHA (C) E + ΔHA - ΔHR ) (D) ΔHA + ΔHR

Description : The rate expression for a heterogeneous catalytic reaction is given by, - rA = K.KA PA(1 + KA.PA + KR.PR), where K is surface reaction rate constant and KA and KR are absorption equilibrium constants of A and R respectively. If KR PR ... R and A) (A) E (B) E + ΔHA (C) E + ΔHA - ΔHR ) (D) ΔHA + ΔHR

Last Answer : (C) E + ΔHA - ΔHR )

In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. normal stress varies linearly in the material c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Description : In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. ... c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Last Answer : c. elastic constants are same in all the directions

A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Description : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Last Answer : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Name the German theoretical physicist who was awarded the Nobel prize for his principle of radiation which states that radiant energy is composed of tiny bits of energy called quanta, the magnitude of which can be calculated by multiplying the frequency of the radiation times a universal constant?

Description : Name the German theoretical physicist who was awarded the Nobel prize for his principle of radiation which states that radiant energy is composed of tiny bits of energy called quanta, the magnitude of which can be calculated by multiplying the frequency of the radiation times a universal constant? 

Last Answer : ANSWER: (MAX) PLANCK

In hydrometer analysis for a soil mass (A) Both meniscus correction and dispersing agent correction are additive (B) Both meniscus correction and dispersing agent correction are subtractive (C) Meniscus correction is additive and dispersing agent correction is subtractive (D) Meniscus correction is subtractive and dispersing agent correction is additive

Description : In hydrometer analysis for a soil mass (A) Both meniscus correction and dispersing agent correction are additive (B) Both meniscus correction and dispersing agent correction are subtractive ... is subtractive (D) Meniscus correction is subtractive and dispersing agent correction is additive

Last Answer : (C) Meniscus correction is additive and dispersing agent correction is subtractive

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box

Rankine's deflection angle in minutes is obtained by multiplying the length of the chord by (A) Degree of the curve (B) Square of the degree of the curve (C) Inverse of the degree of the curve (D) None of these

Description : Rankine's deflection angle in minutes is obtained by multiplying the length of the chord by (A) Degree of the curve (B) Square of the degree of the curve (C) Inverse of the degree of the curve (D) None of these

Last Answer : (A) Degree of the curve

The length of a traverse leg may be obtained by multiplying the latitude and (A) Secant of its reduced bearing (B) Sine of its reduced bearing (C) Cosine of its reduced bearing (D) Tangent of its reduced bearing

Description : The length of a traverse leg may be obtained by multiplying the latitude and (A) Secant of its reduced bearing (B) Sine of its reduced bearing (C) Cosine of its reduced bearing (D) Tangent of its reduced bearing

Last Answer : (A) Secant of its reduced bearing

Pick up the correct statement from the following: (A) The unit hydrograph of a specified unit duration obtained from the past data can be used to obtain the hydrograph of future storms of like duration (B) To obtain the ordinates of storm hydrograph, the ordinates of unit hydrograph are multiplied by the multiplying factor (C) The multiplying factor for storm hydrograph may be obtained by dividing the run off in mm by 25 mm (D) All the above

Description : Pick up the correct statement from the following: (A) The unit hydrograph of a specified unit duration obtained from the past data can be used to obtain the hydrograph of future storms of like duration (B) ... hydrograph may be obtained by dividing the run off in mm by 25 mm (D) All the above

Last Answer : Answer: Option D

If a gauge is installed perpendicular to the slope, its measurement is reduced by multiplying (A) Sine of the angle of inclination with vertical (B) Cosine of the angle of inclination with vertical (C) Tangent of the angle of inclination with vertical (D) Calibration coefficient of the gauge

Description : If a gauge is installed perpendicular to the slope, its measurement is reduced by multiplying (A) Sine of the angle of inclination with vertical (B) Cosine of the angle of inclination with vertical (C) Tangent of the angle of inclination with vertical (D) Calibration coefficient of the gauge

Last Answer : Answer: Option B

In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the earth work is calculated by multiplying the mid-section area by the distance between the two original sections (D) All of the above

Description : In the mid-section formula (A) The mean depth is the average of depths of two consecutive sections (B) The area of mid-sections is calculated by using mean depth (C) The volume of the ... multiplying the mid-section area by the distance between the two original sections (D) All of the above

Last Answer : (D) All of the above

The grade resistance factor for an earth moving machine can be obtained by multiplying grade percentage by a factor approximately equal to (A) 2 kg/tonne (B) 6 kg/tonne (C) 9 kg/tonne (D) 20 kg/tonne

Description : The grade resistance factor for an earth moving machine can be obtained by multiplying grade percentage by a factor approximately equal to (A) 2 kg/tonne (B) 6 kg/tonne (C) 9 kg/tonne (D) 20 kg/tonne

Last Answer : (C) 9 kg/tonne

At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Description : At what height must top rails be fitted above working platform? a. Between 90 cm (35 inches) and 110 cm (43 inches) b. Between 100 cm (39 inches) and 120 cm (47 inches) c. Between 95 cm (38 inches) and 115 cm ( 45 inches) d. Between 105 cm (41 inches)and 125 cm (49 inches)

Last Answer : c. Between 95 cm (38 inches) and 115 cm ( 45 inches)

In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is (A) 5.24 cm (B) 6.24 cm (C) 7.24 cm (D) 8.24 cm

Description : In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is (A) 5.24 cm (B) 6.24 cm (C) 7.24 cm (D) 8.24 cm

Last Answer : (C) 7.24 cm

Does anyone have a dog with angry anal glands? My shih tzu has to have hers emptied about every 3 weeks at the vets..she has a lot of misery from both...

Description : Does anyone have a dog with angry anal glands? My shih tzu has to have hers emptied about every 3 weeks at the vets..she has a lot of misery from both...

Last Answer : I have no personal experience with this… but have you thought of having them removed? Apparently that’s a long-term solution that some people choose.

Male and female cockroaches can be distinguished externally through (a) anal styles in male (b) anal cerci in female (c) anal style and antennae in females (d) both (b) and (c).

Description : Male and female cockroaches can be distinguished externally through (a) anal styles in male (b) anal cerci in female (c) anal style and antennae in females (d) both (b) and (c).

Last Answer : (a) anal styles in male

What external changes are visible after the last moult of a cockroach nymph? (a) Both forewings and hindwings develop (b) Labium develops (c) Mandibles become harder (d) Anal cerci develop

Description : What external changes are visible after the last moult of a cockroach nymph? (a) Both forewings and hindwings develop (b) Labium develops (c) Mandibles become harder (d) Anal cerci develop

Last Answer : (a) Both forewings and hindwings develop

An approach to location anal on analysis that include includes both qualitative and quantitative considerations is a. locational cost-volume b. factor rating c. transportation model d. assignment assignment method e. make or buy analysis

Description : An approach to location anal on analysis that include includes both qualitative and quantitative considerations is a. locational cost-volume b. factor rating c. transportation model d. assignment assignment method e. make or buy analysis

Last Answer : b. factor rating

The constants (Kb, Kr and Kk) used in the laws of crushing (i.e., Bond's law, Rittinger's law and Kick's law) depend upon the (A) Feed material (B) Type of crushing machine (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The constants (Kb, Kr and Kk) used in the laws of crushing (i.e., Bond's law, Rittinger's law and Kick's law) depend upon the (A) Feed material (B) Type of crushing machine (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The breakdown of insulation of the cable can be avoided economically by the use of (a) inter-sheaths (b) insulating materials with different dielectric constants (c) both (a) and (b) (d) none of the above

Description : The breakdown of insulation of the cable can be avoided economically by the use of (a) inter-sheaths (b) insulating materials with different dielectric constants (c) both (a) and (b) (d) none of the above

Last Answer : (c) both (a) and (b)

Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Description : Sluice valves are fitted in a distribution system (A) Along straight length of pipes at suitable intervals (B) At the junctions of the pipes (C) At the branching off points of sub-mains (D) All the above

Last Answer : (D) All the above

The valve fitted closely in a recess against an opening in a pipe, is generally (A) Wedge shaped circular disc (B) Spherical disc (C) Parallelepiped disc (D) Conical shaped circular disc

Description : The valve fitted closely in a recess against an opening in a pipe, is generally (A) Wedge shaped circular disc (B) Spherical disc (C) Parallelepiped disc (D) Conical shaped circular disc

Last Answer : (A) Wedge shaped circular disc

At the socket and spigot joint, (A) Enlarged end of the pipe is called socket (B) Normal end of the pipe is called spigot (C) Spigot is fitted into the socket (D) All the above

Description : At the socket and spigot joint, (A) Enlarged end of the pipe is called socket (B) Normal end of the pipe is called spigot (C) Spigot is fitted into the socket (D) All the above

Last Answer : (D) All the above

Cross hairs in surveying telescopes, are fitted (A) In the objective glass (B) At the centre of the telescope (C) At the optical centre of the eye piece (D) In front of the eye piece

Description : Cross hairs in surveying telescopes, are fitted (A) In the objective glass (B) At the centre of the telescope (C) At the optical centre of the eye piece (D) In front of the eye piece

Last Answer : (D) In front of the eye piece

The diaphragm of a stadia theodolite is fitted with two additional (A) Horizontal hairs (B) Vertical hairs (C) Horizontal and two vertical hairs (D) None of these

Description : The diaphragm of a stadia theodolite is fitted with two additional (A) Horizontal hairs (B) Vertical hairs (C) Horizontal and two vertical hairs (D) None of these

Last Answer : (A) Horizontal hairs

The theodolites used for making tacheometric observations by optical wedge system, are (A) Provided with stadia hairs in front of eye piece (B) Not provided with stadia hairs at all (C) Fitted with a glass wedge inside the telescope (D) Fitted with a glass wedge in front of telescope

Description : The theodolites used for making tacheometric observations by optical wedge system, are (A) Provided with stadia hairs in front of eye piece (B) Not provided with stadia hairs at all (C) Fitted with a glass wedge inside the telescope (D) Fitted with a glass wedge in front of telescope

Last Answer : (D) Fitted with a glass wedge in front of telescope

To avoid large centering error with very short legs, observations are generally made (A) To chain pins (B) By using optical system for centering the theodolite (C) To a target fixed on theodolite tripod on which theodolite may be fitted easily (D) All the above

Description : To avoid large centering error with very short legs, observations are generally made (A) To chain pins (B) By using optical system for centering the theodolite (C) To a target fixed on theodolite tripod on which theodolite may be fitted easily (D) All the above

Last Answer : (C) To a target fixed on theodolite tripod on which theodolite may be fitted easily

A river is said to be of uniform section if in its section A) A segment of a circle can be fitted (B) A parabolic section can be fitted (C) A rectangular section can be fitted (D) All the above

Description : A river is said to be of uniform section if in its section A) A segment of a circle can be fitted (B) A parabolic section can be fitted (C) A rectangular section can be fitted (D) All the above

Last Answer : Answer: Option D

A pipe of length more than double the diameter of orifice fitted externally or internally to the orifice is called a (A) Notch (B) Weir (C) Mouthpiece (D) Nozzle

Description : A pipe of length more than double the diameter of orifice fitted externally or internally to the orifice is called a (A) Notch (B) Weir (C) Mouthpiece (D) Nozzle

Last Answer : Answer: Option C

Pick up the incorrect statement regarding a master trap from the following: (A) It is provided in between the lower end of the house drain and the street sewer (B) It is provided a cleaning eye at the top of the trap (C) The mica flap valve which opens inwards only, is fitted at the top of the inlet pipe (D) The water seal is less than that of ordinary traps

Description : Pick up the incorrect statement regarding a master trap from the following: (A) It is provided in between the lower end of the house drain and the street sewer (B) It is provided a cleaning eye at the ... fitted at the top of the inlet pipe (D) The water seal is less than that of ordinary traps

Last Answer : (D) The water seal is less than that of ordinary traps

Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration permanently. 4. Have nearly uniform discharge. Which of these statements are corrects? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Description : Consider the following statements: Air vessels are fitted on the suction and delivery sides of a reciprocating pump to 1. Achieve higher speed without separation. 2. Reduce work in overcoming frictional resistance. 3. Avoid excessive vibration ... 2 & 3 only (c) 2, 3 & 4 only (d) 1, 2, 3 & 4

Last Answer : (d) 1, 2, 3 & 4

In additive series of intercropping base crop population is — a. Same as pure crop b. Same as intercrop c. Both a & b d. None of these

Description : In additive series of intercropping base crop population is — a. Same as pure crop b. Same as intercrop c. Both a & b d. None of these

Last Answer : a. Same as pure crop