For the reaction as shown in the bellow figure, the rate of formation of Z is 0.2 gm mole/litre.hr. What is the rate of disappearance of X in gm mole/litre.hr? (A) 0.4 (B) 0.1 (C) 0.2 (D) None of these

For the reaction as shown in the bellow figure, the rate of formation
of Z is 0.2 gm mole/litre.hr. What is the rate of disappearance of X in gm
mole/litre.hr?
(A) 0.4
(B) 0.1
(C) 0.2
(D) None of these
by

1 Answer

Answer :

(A) 0.4
by

Related questions

Which of the following holds good for an elementary reaction as shown in the bellow figure? (A) The rate of disappearance of 'Y' is equal to the rate of appearance of 'Z' (B) The rate of disappearance of 'Y' is equal to the rate of disappearance ofX'(C) Three times the rate of disappearance of 'X' is equal to the rate ofappearance of 'Z'(D) The rate of disappearance of 'X' is equal to the rate of appearance of 'Z

Description : Which of the following holds good for an elementary reaction as shown in the bellow figure? (A) The rate of disappearance of 'Y' is equal to the rate of appearance of 'Z' (B) The rate of disappearance of 'Y ... of 'Z' (D) The rate of disappearance of 'X' is equal to the rate of appearance of 'Z

Last Answer : (C) Three times the rate of disappearance of 'X' is equal to the rate of appearance of 'Z

In a chemical reaction as shown in the bellow figure, it is observed that the (i) Rate of formation of 'P' is doubled on doubling the concentration of 'X' (ii) Rate of formation of 'P' is quadrupled on doubling the concentration of 'Y(iii) Doubling the concentration of 'Z' does not affect the rate of formation of 'P' What is the order of the above chemical reaction?(A) Zeroth order (B) First order (C) Second order (D) Third order

Description : In a chemical reaction as shown in the bellow figure, it is observed that the (i) Rate of formation of 'P' is doubled on doubling the concentration of 'X' (ii) Rate of formation of 'P' is quadrupled ... of the above chemical reaction? (A) Zeroth order (B) First order (C) Second order (D) Third order

Last Answer : (D) Third order

Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time requiredto reduce the concentration of reactant from 100 gm moles/litre to 50 gmmoles/litre is same as that required to reduce it from 2 gm moles/litre to 1gm mole/litre in the same volume. Then the order of this reaction is:(A) 0(B) 1(C) 2(D) 3

Description : Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is afunction of reaction temperature. In a chemical reaction, the time required to ... Then the order of this reaction is: (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (B) 1

Decomposition rate of a liquid 'X' which decomposes as per the reaction as shown in the bellow figure is given by: (A) K1 . CX (B) (K1 + K2 + K3 ) CX (C) (K1 + K2 ) CX (D) (K2 + K3 ) CX

Description : Decomposition rate of a liquid 'X' which decomposes as per the reaction as shown in the bellow figure is given by: (A) K1 . CX (B) (K1 + K2 + K3 ) CX (C) (K1 + K2 ) CX (D) (K2 + K3 ) CX

Last Answer : (C) (K1 + K2 ) CX

The order of the chemical reaction as shown in the bellow figure, whose rate equation is given as -rA = KCA 2 . CB is (A) 0 (B) 1 (C) 2 (D) 3

Description : The order of the chemical reaction as shown in the bellow figure, whose rate equation is given as -rA = KCA 2 . CB is (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (D) 3

The first order gas phase reaction as shown in the bellow figure is conducted isothermally in batch mode. The rate of change of conversion with time is given by (A) dXA /dt = k1 (1 - XA ) 2 (1 + 2XA ) (B) dXA /dt = k1 (1 - XA ) (1 + 0.5XA ) (C) dXA /dt = k1 (1 - XA ) (D) dXA /dt = k1 (1 - XA )/(1 + XA )

Description : The first order gas phase reaction as shown in the bellow figure is conducted isothermally in batch mode. The rate of change of conversion with time is given by (A) dXA /dt = k1 (1 - XA ) 2 (1 + 2XA ) (B) dXA /dt = k1 (1 - XA ... 5XA ) (C) dXA /dt = k1 (1 - XA ) (D) dXA /dt = k1 (1 - XA )/(1 + XA )

Last Answer : (C) dXA /dt = k1 (1 - XA

What is the order of chemical reaction as shown in the bellow figure, if it is found that the reaction rate doubles on doubling the concentration of B and also the reaction rate doubles when the concentrations of both A & B were doubled and quadrupled when the concentrations of both B & C were doubled? (A) 1 (B) 2 (C) 3 (D) 4

Description : What is the order of chemical reaction as shown in the bellow figure, if it is found that the reaction rate doubles on doubling the concentration of B and also the reaction rate doubles when the concentrations of both A & B ... the concentrations of both B & C were doubled? (A) 1 (B) 2 (C) 3 (D) 4

Last Answer : (B) 2

In a chemical reaction, represented by as shown in the bellow figure, it is observed that the (i) Rate of reaction increases by a factor of 4 on doubling the concentration of the reactant. (ii) Rate of reaction increases by a factor of 9 on trebling the concentration of the reactant. Then the rate of the reaction is proportional to(where, CA = concentration of the reactant) (A) CA (B) CA 2 (C) CA 3 (D) CA

Description : In a chemical reaction, represented by as shown in the bellow figure, it is observed that the (i) Rate of reaction increases by a factor of 4 on doubling the concentration of the reactant. (ii) Rate of reaction increases ... where, CA = concentration of the reactant) (A) CA (B) CA 2 (C) CA 3 (D) CA

Last Answer : (B) CA 2

What is the Thiele modulus of the solid catalysed first order reaction as shown in the bellow figure, if the pore diffusion offers negligible resistance to reaction? (A) < 5 (B) < 0.5(C) > 1 (D) 5

Description : What is the Thiele modulus of the solid catalysed first order reaction as shown in the bellow figure, if the pore diffusion offers negligible resistance to reaction? (A) < 5 (B) < 0.5 (C) > 1 (D) 5

Last Answer : (B) < 0.5

A consecutive reaction, as shown in the bellow figure, is characterised by(A) Maxima in the concentration of A(B) Maxima in the concentration of B(C) Maxima in the concentration of C(D) High exothermicity

Description : A consecutive reaction, as shown in the bellow figure, is characterised by. (A) Maxima in the concentration of A (B) Maxima in the concentration of B (C) Maxima in the concentration of C (D) High exothermicity

Last Answer : (B) Maxima in the concentration of B

The equilibrium constant for the reversible reaction as shown in the bellow figure, is affected by the (A) Temperature of the system (B) Presence or absence of inerts (C) Pressure of the system (D) Kinetics of the reaction

Description : The equilibrium constant for the reversible reaction as shown in the bellow figure, is affected by the (A) Temperature of the system (B) Presence or absence of inerts (C) Pressure of the system (D) Kinetics of the reaction

Last Answer : (C) Pressure of the system

For a __________ order chemical reaction as shown in the bellow figure, the fractional conversion of reactant 'A' is proportional to time. (A) Zero (B) First (C) Second (D) Third

Description : For a __________ order chemical reaction as shown in the bellow figure, the fractional conversion of reactant 'A' is proportional to time. (A) Zero (B) First (C) Second (D) Third

Last Answer : (A) Zero

For a __________ order chemical reaction as shown in the bellow figure, the half life period is independent of the initial concentration of the reactant A(A) Zero(B) First(C) Second(D) Third.

Description : For a __________ order chemical reaction as shown in the bellow figure, the half life period is independent of the initial concentration of the reactant A. (A) Zero (B) First (C) Second (D) Third

Last Answer : (B) First

Volume change for unimolecular type first order reaction as shown in the bellow figure, increases __________ with time. (A) Linearly (B) Exponentially (C) Parabolically (D) Logarithmically

Description : Volume change for unimolecular type first order reaction as shown in the bellow figure, increases __________ with time. (A) Linearly (B) Exponentially (C) Parabolically (D) Logarithmically

Last Answer : (B) Exponentially

The dimensions of rate constant for reaction 3A → B are (l/gm mole)/min. Therefore the reaction order is (A) 0 (B) 1 (C) 2 (D) 3

Description : The dimensions of rate constant for reaction 3A → B are (l/gm mole)/min. Therefore the reaction order is (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (C) 2

Reaction rate equation for the bellow figure reaction, If S at is present in large excess, what is the order of this reaction? (A) Zero (B) One (C) Two (D) Three

Description : Reaction rate equation for the bellow figure reaction, If S at is present in large excess, what is the order of this reaction? (A) Zero (B) One (C) Two (D) Three

Last Answer : (B) One

What is the unit of the rate constant in a chemical reaction in which 10% of the reactant decomposes in one hour, 20% in two hours, 30% in three hours and so on? (A) Litre/mole.second (B) Moles/litre.second (C) Litre/mole (D) Litre/second

Description : What is the unit of the rate constant in a chemical reaction in which 10% of the reactant decomposes in one hour, 20% in two hours, 30% in three hours and so on? (A) Litre/mole.second (B) Moles/litre.second (C) Litre/mole (D) Litre/second

Last Answer : (A) Litre/mole.second

With increase in K2 /K1 in case of a unimolecular type elementary reactions as shown in the bellow figure, the fractional yield of 'R' in mixed reactor (for a given conversion of 'A'). (A) Decreases (B) Increases (C) Increases linearly (D) Remain same

Description : With increase in K2 /K1 in case of a unimolecular type elementary reactions as shown in the bellow figure, the fractional yield of 'R' in mixed reactor (for a given conversion of 'A'). (A) Decreases (B) Increases (C) Increases linearly (D) Remain same

Last Answer : (A) Decreases

For the reversible reaction A ⇌ 2B, if the equilibrium constant K is 0.05 mole/litre; starting from initially 2 moles of A and zero moles of B, how many moles will be formed at equilibrium? (A) 0.253 (B) 0.338 (C) 0.152 (D) 0.637

Description : For the reversible reaction A ⇌ 2B, if the equilibrium constant K is 0.05 mole/litre; starting from initially 2 moles of A and zero moles of B, how many moles will be formed at equilibrium? (A) 0.253 (B) 0.338 (C) 0.152 (D) 0.637

Last Answer : (B) 0.338

In a first order reaction, the time required to reduce the concentration of reactant from 1 mole/litre to 0.5 mole/litre will be __________ that requiredto reduce it from 10 moles/litre to 5 moles/litre in the same volume.(A) More than(B) Less than(C) Same as(D) Data insufficient; can't be predicted

Description : In a first order reaction, the time required to reduce the concentration of reactant from 1 mole/litre to 0.5 mole/litre will be __________ that requiredto reduce it from 10 moles/litre to 5 moles/litre in the ... (A) More than (B) Less than (C) Same as (D) Data insufficient; can't be predicted

Last Answer : (C) Same as

6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Description : 6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Last Answer : (B) 95%

In case of a consecutive unimolecular types first order reaction asshown in the bellow figure, the concentration of component __________ increases continuously with time. (A) S (B) R (C) A (D) None of these

Description : In case of a consecutive unimolecular types first order reaction asshown in the bellow figure, the concentration of component __________ increases continuously with time. (A) S (B) R (C) A (D) None of these

Last Answer : (A) S

In a consecutive reaction system of the given figure bellow, when E1 is much greater than E2 , the yield of B increases with the (A) Increase of temperature (B) Decrease of temperature (C) Increase in initial concentration of A (D) Decrease in initial concentration of A

Description : In a consecutive reaction system of the given figure bellow, when E1 is much greater than E2 , the yield of B increases with the (A) Increase of temperature (B) Decrease of temperature (C) Increase in initial concentration of A (D) Decrease in initial concentration of A

Last Answer : (A) Increase of temperature

Molarity is defined as the number of gm moles of solute per __________ of solvent. (A) Litre (B) kg (C) gm (D) c.c

Description : Molarity is defined as the number of gm moles of solute per __________ of solvent. (A) Litre (B) kg (C) gm (D) c.c

Last Answer : (A) Litre

Molality is defined as the number of gm moles of solute per __________ of solvent. (A) Litre (B) gm (C) Kg (D) m

Description : Molality is defined as the number of gm moles of solute per __________ of solvent. (A) Litre (B) gm (C) Kg (D) m

Last Answer : (C) Kg

For the equilibrium: `LiCl.3NH_(3(s))hArrLiCl.NH_(3(s))+2NH_(3)`, `K_(p)=9 atm^(2)` at `40^(@)C`. A `5 litre` vessel contains `0.1` mole of `LiCl.NH_(

Description : For the equilibrium: `LiCl.3NH_(3(s))hArrLiCl.NH_(3(s))+2NH_(3)`, `K_(p)=9 atm^(2)` at `40^(@)C`. A `5 litre` vessel contains `0.1` mole of `LiCl.NH_(

Last Answer : For the equilibrium: `LiCl.3NH_(3(s))hArrLiCl.NH_(3(s))+2NH_(3)`, `K_(p)=9 atm^(2)` at `40^( ... backward reaction for completion? A. 5 B. 9 C. 3 D. 1

If `0.5 `mole `H_(2)` is reacted with 0.5 mole `I_(2)` in a ten `-` litre container at `444^(@)C` and at same temperature value of equilibrium constan

Description : If `0.5 `mole `H_(2)` is reacted with 0.5 mole `I_(2)` in a ten `-` litre container at `444^(@)C` and at same temperature value of equilibrium constan

Last Answer : If `0.5 `mole `H_(2)` is reacted with 0.5 mole `I_(2)` in a ten `-` litre container at `444^(@)C` and at ... B. `(1)/(7)` C. `sqrt((1)/(7))` D. 49

Slow sand filter is used if maximum turbidity of raw water is less than (A) 10 gm/litre (B) 20 gm/litre (C) 30 gm/litre (D) 50 gm/litre

Description : Slow sand filter is used if maximum turbidity of raw water is less than (A) 10 gm/litre (B) 20 gm/litre (C) 30 gm/litre (D) 50 gm/litre

Last Answer : (D) 50 gm/litre

Rapid gravity filter can only remove turbidity of water upto (A) 15 to 25 gm/litre (B) 25 to 30 gm/litre (C) 30 to 35 cm/litre (D) 35 to 40 gm/litre

Description : Rapid gravity filter can only remove turbidity of water upto (A) 15 to 25 gm/litre (B) 25 to 30 gm/litre (C) 30 to 35 cm/litre (D) 35 to 40 gm/litre

Last Answer : (D) 35 to 40 gm/litre

In slow sand filters, the turbidity of raw water can be removed only up to (A) 60 mg/litre (B) 75 mg/litre (C) 100 gm/litre (D) 150 mg/litre

Description : In slow sand filters, the turbidity of raw water can be removed only up to  (A) 60 mg/litre  (B) 75 mg/litre  (C) 100 gm/litre  (D) 150 mg/litre 

Last Answer : (A) 60 mg/litre 

The value of gas constant 'R' is (A) 1.987 cal/gm mole °K (B) 1.987 BTU/lb. mole °R (C) Both (A) and (B)(D) Neither (A) nor (B)

Description : The value of gas constant 'R' is (A) 1.987 cal/gm mole °K (B) 1.987 BTU/lb. mole °R (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The conversion in a mixed reactor/accomplishing a reaction A → 3R is 50% when gaseous reactant 'A' is introduced at the rate of 1 litre/second and the leaving flow rate is 2 litres/second. The holding time for this operation is __________ second. (A) 0.5 (B) 1 (C) 2(D) 3

Description : The conversion in a mixed reactor/accomplishing a reaction A → 3R is 50% when gaseous reactant 'A' is introduced at the rate of 1 litre/second and the leaving flow rate is 2 litres/second. The holding time for this operation is __________ second. (A) 0.5 (B) 1 (C) 2 (D) 3

Last Answer : (A) 0.5

The disappearance of the dinosaurs also marks the end of which geological era? w) Precambrian x) Cambrian y) Mesozoic (pron: mez-ah-zo-ik) z) Cenozoic (pron: see-nah-zo-ik)

Description : The disappearance of the dinosaurs also marks the end of which geological era? w) Precambrian x) Cambrian y) Mesozoic (pron: mez-ah-zo-ik) z) Cenozoic (pron: see-nah-zo-ik)

Last Answer : ANSWER: Y -- MESOZOIC

A molar solution is one that contains one mole of a solute in [IIT 1986] (A) 1000 g of the solvent (B) One litre of the solvent (C) One litre of the solution (D) 22.4 litres of the solution

Description : A molar solution is one that contains one mole of a solute in [IIT 1986] (A) 1000 g of the solvent (B) One litre of the solvent (C) One litre of the solution (D) 22.4 litres of the solution

Last Answer : (C) One litre of the solution

Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Description : Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Last Answer : (C) Heat of combustion

One mole on iron [55.8 gm], when oxidised to `+2` oxidation state gives up :

Description : One mole on iron [55.8 gm], when oxidised to `+2` oxidation state gives up :

Last Answer : One mole on iron [55.8 gm], when oxidised to `+2` oxidation state gives up : A. `1N_(A)` electron B ... C. `3N_(A)` electron D. `0.5` mole of electron

An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The residence time required (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Description : An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The ... (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Last Answer : (C) 1.60

The disappearance of the purple color of KMnO4 in its reaction with alkene is known as (a) Markovnikov test (b) Grignard test (c) Baeyer test (d) Wurtz test

Description : The disappearance of the purple color of KMnO4 in its reaction with alkene is known as (a) Markovnikov test (b) Grignard test (c) Baeyer test (d) Wurtz test

Last Answer : Baeyer test

Concentration of the limiting reactant (with initial concentration of a moles/litre) after time t is (a-x). Then 't' for a first order reaction is given by (A) k. t = ln a/(a - x) (B) k. t = x/a (a - x) (C) k. t = ln (a - x)/a (D) k. t = ln a (a - x)/x

Description : Concentration of the limiting reactant (with initial concentration of a moles/litre) after time t is (a-x). Then 't' for a first order reaction is given by (A) k. t = ln a/(a - x) (B) k. t = x/a (a - x) (C) k. t = ln (a - x)/a (D) k. t = ln a (a - x)/x

Last Answer : (A) k. t = ln a/(a - x)

Which line in figure 'A' shown in the illustration represents the interval that the pulse is 'ON'? EL-0088 A. W B. X C. Y D. Z

Description : Which line in figure 'A' shown in the illustration represents the interval that the pulse is 'ON'? EL-0088 A. W B. X C. Y D. Z

Last Answer : Answer: C

Which line in figure 'A' shown in the illustration represents the trailing edge of the wave? EL-0088 A. W B. X C. Y D. Z

Description : Which line in figure 'A' shown in the illustration represents the trailing edge of the wave? EL-0088 A. W B. X C. Y D. Z

Last Answer : Answer: B

Which line in figure 'A' shown in the illustration represents the leading edge of the wave? EL-0088 A. W B. X C. Y D. Z

Description : Which line in figure 'A' shown in the illustration represents the leading edge of the wave? EL-0088 A. W B. X C. Y D. Z

Last Answer : Answer: A

Which line of figure 'A' shown in the illustration represents the interval that the pulse is 'OFF'? EL-0088 A. W B. X C. Y D. Z

Description : Which line of figure 'A' shown in the illustration represents the interval that the pulse is 'OFF'? EL-0088 A. W B. X C. Y D. Z

Last Answer : Answer: D

Which of the following is not a unit of reaction rate? (A) Moles for med/(surface of catalyst) (time) (B) Moles formed/volume of reactor) (time) (C) Mole formed/volume of catalyst) (time) (D) None of these

Description : Which of the following is not a unit of reaction rate? (A) Moles for med/(surface of catalyst) (time) (B) Moles formed/volume of reactor) (time) (C) Mole formed/volume of catalyst) (time) (D) None of these

Last Answer : (D) None of these

The formation of the oxide `M_(x)O_(y)`per mole of `O_(2)` cinsumed is written a `(2x)/(y)M_((S))+O_(2(g))to(2)/(y)M_(x)O_(y)` the free energy change

Description : The formation of the oxide `M_(x)O_(y)`per mole of `O_(2)` cinsumed is written a `(2x)/(y)M_((S))+O_(2(g))to(2)/(y)M_(x)O_(y)` the free energy change

Last Answer : The formation of the oxide `M_(x)O_(y)`per mole of `O_(2)` cinsumed is written ... from the following two reactions. Choose the correct statement

In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is decreasing at a rate of `sqrt5 C//s` Choose the corr

Description : In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is decreasing at a rate of `sqrt5 C//s` Choose the corr

Last Answer : In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is ... a and b are correct D. Both a and b are wrong

Epoxy resin is a polymer containing two or more groups of the bellow fig. is called epoxide group or ethoxyline group. It is a (A) Polyamide & an elastomer (B) Good adhesive (C) Surface coating agent (D) Both (B) and (C)

Description : Epoxy resin is a polymer containing two or more groups of the bellow fig. is called epoxide group or ethoxyline group. It is a (A) Polyamide & an elastomer (B) Good adhesive (C) Surface coating agent (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

What are some common problems associated with bellow expansion joints?

Description : What are some common problems associated with bellow expansion joints?

Last Answer : Bellow expansion joints have gained a reputation for being weak points in piping. Usually they are used to remove piping stresses from equipment or to allow for minor piping moments. If they are ... such method is the use of tie rods between the end flanges to avoid pressure thrust movements