Froude number is not a factor (A) For Reynolds number greater than 300 (B) When there is no vortex formation (C) For unbaffled tank (D) None of these

Froude number is not a factor
(A) For Reynolds number greater than 300
(B) When there is no vortex formation
(C) For unbaffled tank
(D) None of these
by

1 Answer

Answer :

(B) When there is no vortex formation
by

Related questions

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Baffles in mixing tanks are provided to (A) Reduce swirling and vortex formation (B) Increase the structural strength of the tank (C) Aid in rotational flow (D) None of these

Description : Baffles in mixing tanks are provided to (A) Reduce swirling and vortex formation (B) Increase the structural strength of the tank (C) Aid in rotational flow (D) None of these

Last Answer : (A) Reduce swirling and vortex formation

The important dimensional group involved in the power requirement calculation in mixing operation is the __________ number. (A) Reynold's (B) Froude (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The important dimensional group involved in the power requirement calculation in mixing operation is the __________ number. (A) Reynold's (B) Froude (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Description : The co-efficient of drag and lift for an incompressible fluid depends on the (A) Reynolds number (B) Froude number (C) Mach number (D) All (A), (B) and (C)

Last Answer : (A) Reynolds numbe

__________ number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical. (A) Mach (B) Reynolds (C) Froude (D) Weber

Description : __________ number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical. (A) Mach (B) Reynolds (C) Froude (D) Weber

Last Answer : (C) Froude

Ratio of inertia force to elastic force is known as (A) Mach number (B) Froude number (C) Reynolds number (D) Weber's number

Description : Ratio of inertia force to elastic force is known as (A) Mach number (B) Froude number (C) Reynolds number (D) Weber's number

Last Answer : Answer: Option A

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan(D) Np ∝ 1/NRe

Description : For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan (D) Np ∝ 1/NRe

Last Answer : (D) Np ∝ 1/NRe

The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Description : The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Last Answer : (C) N

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

The value of critical Reynolds number for pipe flow is (A) 1,300(B) 10,000 (C) 100,000 (D) None of these

Description : The value of critical Reynolds number for pipe flow is (A) 1,300 (B) 10,000 (C) 100,000 (D) None of these

Last Answer : (A) 1,300

List the various equipment’s used for liquid mixing and explain how vortex formation can be avoided in liquid mixing.

Description : List the various equipment’s used for liquid mixing and explain how vortex formation can be avoided in liquid mixing. 

Last Answer : Equipment used for mixing of liquid:  1. Propeller mixture. 2. Turbine Mixture. 3. Paddle mixture. Vortex formation can be avoided in liquid mixing by making the following changes in the position of the ... the side of vessels. 4. Using push pull propeller. 5. Using baffles.

For a given Reynolds number, in a hydraulically smooth pipe, further smoothening __________ the friction factor. (A) Brings about no further reduction of (B) Increases (C) Decreases (D) None of these

Description : For a given Reynolds number, in a hydraulically smooth pipe, further smoothening __________ the friction factor. (A) Brings about no further reduction of (B) Increases (C) Decreases (D) None of these

Last Answer : (A) Brings about no further reduction of

If Reynolds number is greater than 1, then the (A) Viscous force is larger than the inertia force (B) Inertia force is larger than the viscous force (C) Inertia force is larger than the surface tension force (D) Inertia force is larger than the gravitational force

Description : If Reynolds number is greater than 1, then the (A) Viscous force is larger than the inertia force (B) Inertia force is larger than the viscous force (C) Inertia force is larger than the surface tension force (D) Inertia force is larger than the gravitational force

Last Answer : (B) Inertia force is larger than the viscous force

In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of the laminar film (C) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Description : In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of ... ) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Last Answer : (B) When the roughness projections are much smaller than the thickness of the laminar film

JD factor for mass transfer is a function of Reynolds number. Mass transfer by molecular diffusion from a single drop to surrounding still air is given by (A) Nsh = 2 (B) Nst = 2 (C) Nsc = 2 (D) None of these

Description : JD factor for mass transfer is a function of Reynolds number. Mass transfer by molecular diffusion from a single drop to surrounding still air is given by (A) Nsh = 2 (B) Nst = 2 (C) Nsc = 2 (D) None of these

Last Answer : (A) Nsh = 2

According to Reynolds analogy, Stanton number is equal to (where, f = Fanning friction factor)(A) 2f(B) f(C) f/2(D) f/4

Description : According to Reynolds analogy, Stanton number is equal to (where, f = Fanning friction factor) (A) 2f (B) f (C) f/2 (D) f/4

Last Answer : (C) f/2

Reynold's analogy states that (where, St = Stanton number f = friction factor) (A) St = f/2 (B) St = f/4 (C) St = 4f (D) St = f 1/2

Description : Reynold's analogy states that (where, St = Stanton number f = friction factor) (A) St = f/2 (B) St = f/4 (C) St = 4f (D) St = f 1/2

Last Answer : (A) St = f/2

jH factor for heat transfer is not a function of the __________ number. (A) Reynolds (B) Nusselt (C) Grashoff (D) Both (B) & (C)

Description : jH factor for heat transfer is not a function of the __________ number. (A) Reynolds (B) Nusselt (C) Grashoff (D) Both (B) & (C)

Last Answer : (D) Both (B) & (C)

jH factor for heat transfer depends upon the __________ number. (A) Biot (B) Nusselt (C) Reynolds (D) Prandtl

Description : jH factor for heat transfer depends upon the __________ number. (A) Biot (B) Nusselt (C) Reynolds (D) Prandtl

Last Answer : (C) Reynolds

The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Description : The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Last Answer : (A) Depends only on Reynolds number

The friction factor is (A) Always inversely proportional to the Reynolds number (B) Not dimensionless (C) Not dependent on the roughness of the pipe (D) None of these

Description : The friction factor is (A) Always inversely proportional to the Reynolds number (B) Not dimensionless (C) Not dependent on the roughness of the pipe (D) None of these

Last Answer : (D) None of these

Pick out the correct statement. (A) Fanning friction factor is inversely proportional to Reynolds number always (B) The property of a randomly packed bed (with raschig rings) is given by the ratio of the total volume to the volume of voids in the bed (C) Mach number in an incompressible fluid is always unity (D) Mach number is given by the ratio of the speed of the fluid to that of sound in the fluid under conditions of flow

Description : Pick out the correct statement. (A) Fanning friction factor is inversely proportional to Reynolds number always (B) The property of a randomly packed bed (with raschig rings) is given by the ratio of the ... the ratio of the speed of the fluid to that of sound in the fluid under conditions of flow

Last Answer : (D) Mach number is given by the ratio of the speed of the fluid to that of sound in the fluid under conditions of flow

Which of the following quantities are computed by using the hydraulic radius for non-circular ducts? (A) Velocity and relative roughness (B) Head loss and velocity (C) Reynold number, relative roughness and head loss (D) Reynolds number and friction factor

Description : Which of the following quantities are computed by using the hydraulic radius for non-circular ducts? (A) Velocity and relative roughness (B) Head loss and velocity (C) Reynold number, relative roughness and head loss (D) Reynolds number and friction factor

Last Answer : (C) Reynold number, relative roughness and head loss

A pipe is defined as 'hydraulically smooth', if the friction factor (A) Is not a function of Reynolds number (B) For a given Reynolds number remains constant even on further smoothening of the pipe (C) Is zero irrespective of the Reynolds number (D) None of these

Description : A pipe is defined as 'hydraulically smooth', if the friction factor (A) Is not a function of Reynolds number (B) For a given Reynolds number remains constant even on further smoothening of the pipe (C) Is zero irrespective of the Reynolds number (D) None of these

Last Answer : (B) For a given Reynolds number remains constant even on further smoothening of the pipe

Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Which is not concerned directly with mass transfer? (A) Schmidt number (B) Sherwood number (C) Lewis relationship (D) Froude number

Description : Which is not concerned directly with mass transfer? (A) Schmidt number (B) Sherwood number (C) Lewis relationship (D) Froude number

Last Answer : (D) Froude number

Which of the following is concerned with both heat and mass transfer? (A) Lewis relationship (B) Nusselt number (C) Kutateladze number (D) Froude number

Description : Which of the following is concerned with both heat and mass transfer? (A) Lewis relationship (B) Nusselt number (C) Kutateladze number (D) Froude number

Last Answer : (A) Lewis relationship

The ratio of inertial forces to gravity forces is called the __________ number. (A) Mach (B) Froude (C) Euler (D) Weber

Description : The ratio of inertial forces to gravity forces is called the __________ number. (A) Mach (B) Froude (C) Euler (D) Weber

Last Answer : (B) Froude

Which of the following is not dimension-less? (A) Froude number (B) Kinematic viscosity (C) Pressure co-efficient (D) None of these

Description : Which of the following is not dimension-less? (A) Froude number (B) Kinematic viscosity (C) Pressure co-efficient (D) None of these

Last Answer : (B) Kinematic viscosity

Which of the following is not concerned with the fluid-particle interaction? (A) Drag co-efficient (B) Froude number (C) Galileo number (D) Weber number

Description : Which of the following is not concerned with the fluid-particle interaction? (A) Drag co-efficient (B) Froude number (C) Galileo number (D) Weber number

Last Answer : (D) Weber number

Ratio of pressure and inertia force gives __________ number. (A) Weber (B) Mach (C) Euler (D) Froude

Description : Ratio of pressure and inertia force gives __________ number. (A) Weber (B) Mach (C) Euler (D) Froude

Last Answer : (C) Euler

Froude number is the ratio of (A) Shear stress to gravitational stress (B) Drag stress to shear stress (C) Inertial stress to shear stress (D) Inertial stress to gravitational stress

Description : Froude number is the ratio of (A) Shear stress to gravitational stress (B) Drag stress to shear stress (C) Inertial stress to shear stress (D) Inertial stress to gravitational stress

Last Answer : (D) Inertial stress to gravitational stress

Ratio of inertial forces to surface tension forces is called the __________ number. (A) Euler (B) Froude (C) Mach (D) Weber

Description : Ratio of inertial forces to surface tension forces is called the __________ number. (A) Euler (B) Froude (C) Mach (D) Weber

Last Answer : (D) Weber

Which of the following is not a dimension-less parameter? (A) Pressure-co-efficient (B) Froude number (C) Kinematic viscosity (D) Weber number

Description : Which of the following is not a dimension-less parameter? (A) Pressure-co-efficient (B) Froude number (C) Kinematic viscosity (D) Weber number

Last Answer : (C) Kinematic viscosity

The ratio of inertial forces to viscous forces is called the __________ number. (A) Weber (B) Mach (C) Froude (D) Reynold

Description : The ratio of inertial forces to viscous forces is called the __________ number. (A) Weber (B) Mach (C) Froude (D) Reynold

Last Answer : (D) Reynold

The ratio of pressure forces to inertial forces is called the __________ number. (A) Froude (B) Euler (C) Reynold (D) Mach

Description : The ratio of pressure forces to inertial forces is called the __________ number. (A) Froude (B) Euler (C) Reynold (D) Mach

Last Answer : (B) Euler

Pick out the correct statement. (A) A forced vortex occurs when fluid rotates as a solid about an axis (B) In laminar flow, Newton's law of viscosity does not apply (C) A free vortex occurs, when fluid rotates as a solid (D) In turbulent flow, there are neither cross-currents nor eddies

Description : Pick out the correct statement. (A) A forced vortex occurs when fluid rotates as a solid about an axis (B) In laminar flow, Newton's law of viscosity does not apply (C) A free vortex occurs, when fluid rotates as a solid (D) In turbulent flow, there are neither cross-currents nor eddies

Last Answer : (A) A forced vortex occurs when fluid rotates as a solid about an axis

In a free vortex, the (A) Velocity changes linearly with radial distance (B) Flow is necessarily rotational (C) Radial component of velocity is same everywhere (D) Stream lines are not circular

Description : In a free vortex, the (A) Velocity changes linearly with radial distance (B) Flow is necessarily rotational (C) Radial component of velocity is same everywhere (D) Stream lines are not circular

Last Answer : (A) Velocity changes linearly with radial distance

Under what circumstances are vortex flowmeters the most accurate?

Description : Under what circumstances are vortex flowmeters the most accurate?

Last Answer : The accuracy of vortex flowmeters can be within 1% so long as they’re being operating within their recommended flow range, have a steady stream, and you have 10 pipe diameters of straight pipe behind the in front of the flowmeters. Outside of these parameters, these flowmeters are not accurate.

02. The ratio of the inertia force to the gravity force is called Froude number. A) Agree B) Disagree

Description : 02. The ratio of the inertia force to the gravity force is called Froude number. A) Agree B) Disagree

Last Answer : A

Ratio of inertia force to surface Jension is known as (A) Mach number (B) Froude number (C) (D) Weber's number

Description : Ratio of inertia force to surface Jension is known as (A) Mach number (B) Froude number (C) (D) Weber's number

Last Answer : Answer: Option D

Froude number is significant in (A) Supersonics, as with projectile and jet propulsion (B) Full immersion or completely enclosed flow, as with pipes, aircraft wings, nozzles etc. (C) Simultaneous motion through two fluids where there is a surface of discontinuity, gravity forces, and wave making effect, as with ship's hulls (D) All of the above

Description : Froude number is significant in (A) Supersonics, as with projectile and jet propulsion (B) Full immersion or completely enclosed flow, as with pipes, aircraft wings, nozzles etc. (C) Simultaneous motion ... gravity forces, and wave making effect, as with ship's hulls (D) All of the above

Last Answer : Answer: Option C

The molecular number density of an ideal gas at standard temperature and pressure in cm3  a. Froude number  b. Loschmidt number  c. Mach number  d. Reynold number

Description : The molecular number density of an ideal gas at standard temperature and pressure in cm3  a. Froude number  b. Loschmidt number  c. Mach number  d. Reynold number

Last Answer : Loschmidt number

Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a given discharge. 4. The Froude number is equal to unity. Which of these statements are correct? (a) 1 , 2 & 3 only (b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Description : Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a ... b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Last Answer : (b) 1, 2, 3 & 4

Who can teach me how to find the Volume number and Issue number of “Numerical simulation of three dimensional cavitation shedding dynamics with special emphasis on cavitation–vortex interaction”?

Description : Who can teach me how to find the Volume number and Issue number of “Numerical simulation of three dimensional cavitation shedding dynamics with special emphasis on cavitation–vortex interaction”?

Last Answer : Google it. \ http://www.sciencedirect.com/science/article/pii/S0029801814001838

Is "Polar Vortex" a new term to stoke up weather hysteria?

Description : Is "Polar Vortex" a new term to stoke up weather hysteria?

Last Answer : 20 years from now it will be called a “Solar Ice Stream”.

Explain the difference between vortex friction and vortex friction ?

Description : Explain the difference between vortex friction and vortex friction ?

Last Answer : The friction that occurs when an object tries to slip or rub on the surface of another object, that is, when it moves, and the friction that acts against the motion when an object rolls ... to cyclic friction. Undoubtedly, the value of rotational friction is much lower than that of bismuth friction.

Is the vortex on the same side everywhere in the world?

Last Answer : we learned that at school, but I wasn't anywhere to verify it, so I can only believe it ...