A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

A fuel with high heat release rate will
(A) Require smaller combustion chamber
(B) Have high calorific value
(C) Have high adiabatic flame temperature
(D) None of these
by

1 Answer

Answer :

(A) Require smaller combustion chamber
by

Related questions

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation(C) Ignites easily and burns with long smoky flame(D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Description : If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Last Answer : (A) Low(A) Low

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Description : With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Last Answer : (D) May increase or decrease; depends on the quantity of products of combustion

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Description : Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only

Last Answer : (A) Range of fuel firing rates

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The optimum percentage of excess air for combustion depends upon the__________ of the fuel.(A) Type (solid, liquid or gaseous)(B) Calorific value(C) Sulphur content(D) Ignition temperature

Description : The optimum percentage of excess air for combustion depends upon the__________ of the fuel. (A) Type (solid, liquid or gaseous) (B) Calorific value (C) Sulphur content (D) Ignition temperature

Last Answer : (A) Type (solid, liquid or gaseous)

The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Description : The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Last Answer : (A) Much lower

The maximum adiabatic flame temperature is attained, when the fuel is burnt with (A) Theoretically required amount of air(B) More than theoretically required amount of air(C) Less than theoretically required amount of air(D) Theoretically required amount of oxygen

Description : The maximum adiabatic flame temperature is attained, when the fuel is burnt with (A) Theoretically required amount of air (B) More than theoretically required amount of air (C) Less than theoretically required amount of air (D) Theoretically required amount of oxygen

Last Answer : (D) Theoretically required amount of oxygen

Adiabatic flame temperature of a fuel is dependent on the initial temperature of (A) Fuel (B) Air (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Adiabatic flame temperature of a fuel is dependent on the initial temperature of (A) Fuel (B) Air (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Description : Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Last Answer : (C) Both (A) & (B)

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Description : Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Last Answer : (D) None of these

A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) Is more difficult to ignite and produces a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Description : A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) ... a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Last Answer : (D) None of these

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Water is a better coolant than a gas (like CO2 , He, N2 etc.), because it (A) Is a better neutron moderator as well (B) Require comparatively smaller pumps and heat exchanger for a given heat transfer rate (C) Has a better heat transfer characteristics, and it can be pressurised to attain a high temperature (D) All (A), (B) and (C)

Description : Water is a better coolant than a gas (like CO2 , He, N2 etc.), because it (A) Is a better neutron moderator as well (B) Require comparatively smaller pumps and heat exchanger for a given heat transfer rate ... , and it can be pressurised to attain a high temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas because of the color of the flame, when it is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Description : Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas ... is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Last Answer : (B) Acetylene gas cannot be used for illumination purpose

Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C(A) Sensible (B) Latent (C) Sensible and latent (D) None of these.

Description : Net calorific value is the gross calorific value less the __________ heat of water in the product of combustion when cooled to 15°C. (A) Sensible (B) Latent (C) Sensible and latent (D) None of these

Last Answer : (C) Sensible and latent

Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Description : Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Last Answer : (C) Heat of combustion

In adiabatic evaporative cooling, heat transfer between chamber and surroundings is ____ A. zero B. high C. low D. none of the mentioned

Description : In adiabatic evaporative cooling, heat transfer between chamber and surroundings is ____ A. zero B. high C. low D. none of the mentioned

Last Answer : ANSWER : A

Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Description : Combustion of pulverised fuel (A) Requires larger combustion chamber than rich gaseous fuel (B) In a metallurgical furnace does not contaminate the product in the furnace by ash from fuel (C) Suppresses the discharge of fine dust and grit into atmosphere (D) All (A), (B) and (C)

Last Answer : (A) Requires larger combustion chamber than rich gaseous fuel

For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Description : For long flame and easy ignition, the coal used should have (A) High volatile matter (B) Low ash (C) High calorific value (D) High ash

Last Answer : (A) High volatile matter

Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Description : Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Last Answer : (A) Amount of heat liberated

A coal containing high amount of volatile matter will have (A) Low ignition temperature (B) Very little ash content (C) High fusion point of its ash (D) Low adiabatic flame temperature

Description : A coal containing high amount of volatile matter will have (A) Low ignition temperature (B) Very little ash content (C) High fusion point of its ash (D) Low adiabatic flame temperature

Last Answer : (A) Low ignition temperature

In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Description : In a 4 S diesel engine, the term ‘squish’ refers to the (a) Injection of fuel in the precombustion chamber (b) Discharge of gases from the precombustion chamber (c) Entry of air into the combustion chamber (d) Stripping of fuel from the core

Last Answer : Ans :c

Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Last Answer : (B) Better combustion

The ratio of maximum adiabatic flame temperature in air to that in pure oxygen is always (A) 1 (B) < 1 (C) > 1 (D) Unpredictable

Description : The ratio of maximum adiabatic flame temperature in air to that in pure oxygen is always (A) 1 (B) < 1 (C) > 1 (D) Unpredictable

Last Answer : (B) < 1

The maximum adiabatic flame temperature in air is __________ the maximum flame temperature in pure oxygen. (A) Lower than (B) Higher than(C) Same as(D) Not related to

Description : The maximum adiabatic flame temperature in air is __________ the maximum flame temperature in pure oxygen. (A) Lower than (B) Higher than (C) Same as (D) Not related to

Last Answer : (A) Lower than

Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these

Description : Rate of heat release in a furnace, which is the measure of heat intensity, is defined as (A) kcal/hr/m3 combustion space (B) kcal/m3 combustion space (C) kcal/hr (D) None of these

Last Answer : (A) kcal/hr/m3 combustion space