Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Use of preheated air for combustion of fuel in the furnace, increases the
(A) Scale losses of the furnace stock
(B) Calorific value of the fuel
(C) Flame temperature
(D) None of these
by

1 Answer

Answer :

(C) Flame temperature
by

Related questions

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Description : If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Last Answer : (A) Low(A) Low

Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the fluegas outlet temperature from the soaking pit is 1200°C.(A) 5(B) 60(C) 20(D) 40

Description : Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the flue gas outlet temperature from the soaking pit is 1200°C. (A) 5 (B) 60 (C) 20 (D) 40

Last Answer : (C) 20

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Description : Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Last Answer : (C) 20

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

The optimum percentage of excess air for combustion depends upon the__________ of the fuel.(A) Type (solid, liquid or gaseous)(B) Calorific value(C) Sulphur content(D) Ignition temperature

Description : The optimum percentage of excess air for combustion depends upon the__________ of the fuel. (A) Type (solid, liquid or gaseous) (B) Calorific value (C) Sulphur content (D) Ignition temperature

Last Answer : (A) Type (solid, liquid or gaseous)

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Description : With increase in calorific value of fuels, their adiabatic flame temperatures (A) Increase (B) Decrease (C) Remain unchanged (D) May increase or decrease; depends on the quantity of products of combustion

Last Answer : (D) May increase or decrease; depends on the quantity of products of combustion

In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

Use of pulverised coal in boilers provides (A) Higher calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace wall

Description : Use of pulverised coal in boilers provides (A) Higher calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace wall

Last Answer : (B) Better combustion

Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Last Answer : (B) Better combustion

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Description : During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Last Answer : (A) Lengthens the flame

Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Description : Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Last Answer : (A) Controlling the excess air

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Description : Which of the following constituents of a fuel does not contribute to its calorific value on combustion? (A) Hydrogen (B) Sulphur (C) Carbon (D) None of these

Last Answer : (D) None of these

During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Description : During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Description : Tar is a better fuel than furnace oil, because of its (A) Higher calorific value (B) Lower sulphur content (C) Higher emissivity (0.8-0.9) resulting in higher radiation heat transfer rate (D) Both (A) and (B)

Last Answer : (D) Both (A) and (B)

Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Description : Out of the following fuels, the difference between the net and gross calorific value is maximum in case of (A) Pitch (B) Fuel oil (C) Blast furnace gas (D) Bituminous coal

Last Answer : (B) Fuel oil

Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Description : Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Last Answer : (C) Both (A) & (B)

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Description : Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Last Answer : (C) Friability & oxygen content

With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Description : With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Last Answer : (D) None of these

In the blast furnace, incorporation of water vapour in the blast gives the following effect. (A) Increases the reducing potential of the gas (B) Increases the flame temperature (C) No significant change occurs (D) Increases the hydrogen content in the metal

Description : In the blast furnace, incorporation of water vapour in the blast gives the following effect. (A) Increases the reducing potential of the gas (B) Increases the flame temperature (C) No significant change occurs (D) Increases the hydrogen content in the metal

Last Answer : (A) Increases the reducing potential of the gas

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Description : Which of the following fuel gases will require maximum amount of air for combustion of 1 Nm3 gas? (A) Blast furnace gas (B) Natural gas (C) Producer gas (D) Water gas

Last Answer : (B) Natural gas

Smoke is produced due to (A) Insufficient supply of combustion air and insufficient time for combustion (B) Poor quality of fuel and improper mixing of fuel & combustion air (C) Poor design & overloading of furnace (D) All (A), (B) and (C)

Description : Smoke is produced due to (A) Insufficient supply of combustion air and insufficient time for combustion (B) Poor quality of fuel and improper mixing of fuel & combustion air (C) Poor design & overloading of furnace (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3