Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Presence of nitrogen in combustion air does not reduce the
(A) Amount of heat liberated
(B) Flame temperature
(C) Flue gas temperature
(D) Any of the above
by

1 Answer

Answer :

(A) Amount of heat liberated
by

Related questions

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Orsat apparatus is meant for (A) Gravimetric analysis of flue gas (B) Finding out combustion efficiency (C) Direct determination of nitrogen in flue gas by absorbing it in ammoniacal cuprous chloride (D) None of these

Description : Orsat apparatus is meant for (A) Gravimetric analysis of flue gas (B) Finding out combustion efficiency (C) Direct determination of nitrogen in flue gas by absorbing it in ammoniacal cuprous chloride (D) None of these

Last Answer : (D) None of these

Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Description : Ostwald charts are meant for (A) Computing the excess/deficiency of combustion air (B) Calculation of flue gas temperature (C) Computation of flue gas analysis (D) None of these

Last Answer : (A) Computing the excess/deficiency of combustion air

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Description : Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Last Answer : preheating the boiler feed water

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Description : When incomplete combustion loss is high, the flue gas analysis shows large amount of (A) CO2 (B) CO (C) O2 (D) C

Last Answer : (B) CO

Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Description : Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Last Answer : (B) Flame temperature

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation(C) Ignites easily and burns with long smoky flame(D) All (A), (B) and (C)

Description : A coal having high amount of volatile matter (A) Would require smaller combustion chamber (B) Produces very little of tar and gas on carbonisation (C) Ignites easily and burns with long smoky flame (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20

23. Infrared thermometer is used to measure a) Surface temperature b) Flame temperature c) Flue gas temperature d) Hot water temperature

Description : Infrared thermometer is used to measure a) Surface temperature b) Flame temperature c) Flue gas temperature d) Hot water temperature

Last Answer : Surface temperature

16. Infrared thermometer is used to measure a) Surface temperature b) Flame temperature c) Flue gas temperature d) Hot water temperature

Description : Infrared thermometer is used to measure a) Surface temperature b) Flame temperature c) Flue gas temperature d) Hot water temperature

Last Answer : Surface temperature

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Description : Efficiency of the combustion of a fuel is judged by the __________ the flue gas. (A) % of CO2 in (B) % of O2 in (C) Temperature of (D) Colour of

Last Answer : (B) % of O2 in

Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Description : Incomplete combustion of a fuel is characterised by the high __________ in the flue gas. (A) Smoke (B) Temperature (C) Oxygen (D) Carbon monoxide

Last Answer : (D) Carbon monoxide

Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature (C) Electrostatic precipitator is the most efficient dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Description : Pick out the wrong statement. (A) A slight haze at the top of chimney indicates good combustion in the furnace (B) A bag filter incurs very small pressure drop and is very efficient for ... dust collection equipment for removal of submicronic dust particles present in flue gas (D) None of these

Last Answer : (B) A bag filter incurs very small pressure drop and is very efficient for removal of submicronic dust particles from flue gases at very high temperature

In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & structural materials of furnace (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Description : In a furnace, the heat taken by the charge/stock and the heat lost to the furnace structure & flue gases depends on the (A) Rate of firing and emissivity of flame (B) Thermal conductivity of the charge & ... (C) Nature of process; whether batch, continuous or intermittent (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Description : Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Last Answer : (C) Both (A) & (B)

Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Description : If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Last Answer : (A) Low(A) Low

Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Description : Oxygen trim control strategy __ a. continuously measures the oxygen content in the flue gas b. adjusts the combustion air flow c. Continually tuning the air-fuel mixture. d. All of above

Last Answer : d. All of above

Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas because of the color of the flame, when it is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Description : Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas ... is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Last Answer : (B) Acetylene gas cannot be used for illumination purpose

measures oxygen and temperature of the flue gas. a) Fuel efficiency monitor. b) Combustion analyzer. c) Contact thermometer. d) Infrared thermometer.

Description : measures oxygen and temperature of the flue gas. a) Fuel efficiency monitor. b) Combustion analyzer. c) Contact thermometer. d) Infrared thermometer.

Last Answer : Combustion analyzer

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Description : During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Last Answer : (A) Lengthens the flame

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature