Theoretical flame temperature of a fuel is that temperature which is attained, when the fuel is completely burnt 'using theoretical amount of air in (A) Air (B) Oxygen (C) Either (A) or (B) (D) Either (A) or (B) without gain or loss of heat

Theoretical flame temperature of a fuel is that temperature which is
attained, when the fuel is completely burnt 'using theoretical amount of air
in
(A) Air
(B) Oxygen
(C) Either (A) or (B)
(D) Either (A) or (B) without gain or loss of heat
by

1 Answer

Answer :

(D) Either (A) or (B) without gain or loss of heat
by

Related questions

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

The maximum adiabatic flame temperature is attained, when the fuel is burnt with (A) Theoretically required amount of air(B) More than theoretically required amount of air(C) Less than theoretically required amount of air(D) Theoretically required amount of oxygen

Description : The maximum adiabatic flame temperature is attained, when the fuel is burnt with (A) Theoretically required amount of air (B) More than theoretically required amount of air (C) Less than theoretically required amount of air (D) Theoretically required amount of oxygen

Last Answer : (D) Theoretically required amount of oxygen

The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Description : The maximum adiabatic flame temperature in air as compared to that in pure oxygen is (A) Much lower (B) Much higher (C) Same (D) Either lower or higher, depends on the type of fuel

Last Answer : (A) Much lower

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

Smoke point of kerosene is the (A) Time after which smoking starts on burning (B) Temperature at which smoking starts (C) Maximum height of flame (in mm) without causing smoking, when burnt in a standard lamp (D) None of these

Description : Smoke point of kerosene is the (A) Time after which smoking starts on burning (B) Temperature at which smoking starts (C) Maximum height of flame (in mm) without causing smoking, when burnt in a standard lamp (D) None of these

Last Answer : (B) Temperature at which smoking starts

Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Description : Deficiency of combustion air during combustion of a gaseous fuel (A) Lengthens the flame (B) Causes heat loss of fuel by its partial combustion (C) Both (A) & (B) (D) Shortens the flame

Last Answer : (C) Both (A) & (B)

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas because of the color of the flame, when it is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Description : Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas ... is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Last Answer : (B) Acetylene gas cannot be used for illumination purpose

Which of the following has the highest theoretical flame temperature? (A) Blast furnace gas (B) Hydrogen (C) Acetylene (D) Coke oven gas

Description : Which of the following has the highest theoretical flame temperature? (A) Blast furnace gas (B) Hydrogen (C) Acetylene (D) Coke oven gas

Last Answer : (C) Acetylene

Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Description : Blast furnace gas compared to coke oven gas has (A) Lower ignition temperature (B) Narrower limit of inflammability (C) Higher calorific value (D) Lower theoretical flame temperature

Last Answer : (D) Lower theoretical flame temperature

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Pure carbon is completely burnt in oxygen. The flue gas analysis is 70%CO2 , 20%CO and 10%O2 . The percent excess oxygen used is (A) 20 (B) 12.5 (C) 0 (D) 10

Description : Pure carbon is completely burnt in oxygen. The flue gas analysis is 70%CO2 , 20%CO and 10%O2 . The percent excess oxygen used is (A) 20 (B) 12.5 (C) 0 (D) 10

Last Answer : (C) 0

6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Description : 6 gm of carbon is burnt with an amount of air containing 18 gm oxygen. The product contains 16.5 gms CO2 and 2.8 gms CO besides other constituents. What is the degree of conversion on the basis of disappearance of limiting reactant? (A) 100% (B) 95% (C) 75% (D) 20%

Last Answer : (B) 95%

Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Description : Presence of nitrogen in combustion air does not reduce the (A) Amount of heat liberated (B) Flame temperature (C) Flue gas temperature (D) Any of the above

Last Answer : (A) Amount of heat liberated

A fuel containing carbon and carbon monoxide (but containing no hydrogen or its compounds) is burnt in pure oxygen at constant pressure. Its gross calorific value as compared to net calorific value will be (A) More (B) Less (C) Same (D) Data insufficient; can't be predicted

Description : A fuel containing carbon and carbon monoxide (but containing no hydrogen or its compounds) is burnt in pure oxygen at constant pressure. Its gross calorific value as compared to net calorific value will be (A) More (B) Less (C) Same (D) Data insufficient; can't be predicted

Last Answer : (C) Same

Ignition temperature of a fuel in air is __________ that in pure oxygen. (A) More than(B) Less than(C) Equal to(D) Either more or less; depends on the type of fuel

Description : Ignition temperature of a fuel in air is __________ that in pure oxygen. (A) More than (B) Less than (C) Equal to (D) Either more or less; depends on the type of fuel

Last Answer : (A) More than

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Description : A fuel with high heat release rate will (A) Require smaller combustion chamber (B) Have high calorific value (C) Have high adiabatic flame temperature (D) None of these

Last Answer : (A) Require smaller combustion chamber

If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Description : If the specific heat of gaseous products of combustion of a fuel is high, the abiabatic flame temperature will be (A) Low (B) High (C) Very high, if the fuel is of low calorific value (D) None of these

Last Answer : (A) Low(A) Low

The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler. (A) Evaporative capacity (B) Evaporation efficiency (C) Thermal efficiency (D) Steam load

Description : The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler. (A) Evaporative capacity (B) Evaporation efficiency (C) Thermal efficiency (D) Steam load

Last Answer : (A) Evaporative capacity

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Description : For the case of a fuel gas undergoing combustion with air, if the air/fuel ratio is increased, the adiabatic flame temperature will (A) Increase (B) Decrease (C) Increase or decrease depending on the fuel type (D) Not change

Last Answer : (B) Decrease

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Adiabatic flame temperature of a fuel is dependent on the initial temperature of (A) Fuel (B) Air (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Adiabatic flame temperature of a fuel is dependent on the initial temperature of (A) Fuel (B) Air (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Description : During combustion of a gaseous fuel, the presence of a non-luminous flame is an indication of the (A) Incomplete combustion (B) Complete combustion (C) High oxygen in flue gas (D) None of these

Last Answer : (B) Complete combustion

Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Description : Change of heat content when one mole of compound is burnt in oxygen at constant pressure is called the (A) Calorific value (B) Heat of reaction (C) Heat of combustion (D) Heat of formation

Last Answer : (C) Heat of combustion

Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be (A) 9.5 : 1 (B) 12.5 : 1 (C) 15.5 : 1 (D) 18.5 : 1

Description : Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be (A) 9.5 : 1 (B) 12.5 : 1 (C) 15.5 : 1 (D) 18.5 : 1

Last Answer : (A) 9.5 : 1

Air/fuel ratio by weight for combustion of methane with theoretical quantity of air will be about (A) 9 : 1 (B) 17 : 1 (C) 23 : 1 (D) 29 : 1

Description : Air/fuel ratio by weight for combustion of methane with theoretical quantity of air will be about (A) 9 : 1 (B) 17 : 1 (C) 23 : 1 (D) 29 : 1

Last Answer : (B) 17 : 1

The ratio of maximum adiabatic flame temperature in air to that in pure oxygen is always (A) 1 (B) < 1 (C) > 1 (D) Unpredictable

Description : The ratio of maximum adiabatic flame temperature in air to that in pure oxygen is always (A) 1 (B) < 1 (C) > 1 (D) Unpredictable

Last Answer : (B) < 1

The maximum adiabatic flame temperature in air is __________ the maximum flame temperature in pure oxygen. (A) Lower than (B) Higher than(C) Same as(D) Not related to

Description : The maximum adiabatic flame temperature in air is __________ the maximum flame temperature in pure oxygen. (A) Lower than (B) Higher than (C) Same as (D) Not related to

Last Answer : (A) Lower than

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

__________ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas￾vapor mixture. (A) Dry bulb (B) Wet bulb (C) Dew point (D) None of these

Description : __________ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas￾vapor mixture. (A) Dry bulb (B) Wet bulb (C) Dew point (D) None of these

Last Answer : (B) Wet bulb

Combustion is the ideal air/fuel ratio where a. the mixing proportion is correct, b. the fuel is completely burned c. the oxygen is entirely consumed d. All of the above

Description : Combustion is the ideal air/fuel ratio where a. the mixing proportion is correct, b. the fuel is completely burned c. the oxygen is entirely consumed d. All of the above

Last Answer : d. All of the above

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

_____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Description : _____________ senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio. a) Engine temperature b) Exhaust gas c) Air flow d) Air inlet temperature

Last Answer : Answer: b Explanation: Exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates airfuel ratio while engine temperature sensor senses the temperature of the engine coolant, and from this data the computer adjusts the mixture strength to rich side for cold starting.

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Description : Preheating of a gaseous fuel results in increased (A) Flame length (B) Flame temperature (C) Quantity of flue gas

Last Answer : (B) Flame temperature

Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of theoretical plate calculation for distillation column (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Description : Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of ... (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Last Answer : (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column