Describe Effect of misalignment of direct coupled drives.

Describe Effect of misalignment of direct coupled drives.
by

1 Answer

Answer :

Following are the effects of misalignment of direct coupled drives:- 1. There will be excess vibrations. 2. Increase in noise level. 3. Increases in friction loss. 4. The shaft will bent. 5. There will be premature failure of bearing and coupling 6. It will increases maintenance cost. 7. It will increases temperature of bearings. 8. It will increases energy consumption 9. It will reduces overall performance of machine. 10. It will reduces motor efficiency 11. Loose or broken foundation bolts and coupling bolts 12. Increases stresses on coupling & shaft. 13. Early wear & tear of both driving & driven machine.

by

Related questions

Compare direct and Indirect method of testing.

Description : Compare direct and Indirect method of testing.  

Last Answer : Sr No.  Parameter Direct Testing Indirect Testing   1 Nature of loading  The m/c is actually loaded at full load. The m/c is not actually loaded but machine run on N.L. 2 ... 1.O.C. and S.C test on transformer/Alternator / I.M. , 2. Swinburne test on DC machines. 

Describe any four methods used to reduce earth resistance.

Description : Describe any four methods used to reduce earth resistance.  

Last Answer : To reduce earth resistance following steps/methods are necessary: 1. Earth pit of more depth & width- breadth should be made. 2. Use of higher size/cross section of earthing material like ... galvanized. 12. Electrodes should be placed in the earth in the upright vertical position. 

Describe the factors affecting preventive maintenance schedule.

Description : Describe the factors affecting preventive maintenance schedule. 

Last Answer : Following factors affect the PM schedule:- 1. Non availability of spares & raw material. 2. Non availability of tools, trackless, jacks, fixture required for PM. 3. Non availability of trained & skilled ... the work is held up for certain period. This is also a cause of disturbing a PM schedule.

If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind its normal position as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Description : If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind ... as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Last Answer : Answer: A

If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind its normal position as it rotates. This hu A. amortisseur windings B. direct coupling C. increase governor speed droop D. decreasing governor speed droop

Description : If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ... windings B. direct coupling C. increase governor speed droop D. decreasing governor speed droop

Last Answer : Answer: A

advantages and disadvantages of direct coupled amplifier over RC coupled amplifier.

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

Direct X is a ______1) Computer Part 2) Software that drives Graphic hardware 3) A User Interface 4) None of these

Description : Direct X is a ______ 1) Computer Part 2) Software that drives Graphic hardware 3) A User Interface 4) None of these

Last Answer : 2) Software that drives Graphic hardware

All the following statements about brown adipose tissue are true except (A) It is rich in cytochromes (B) It oxidizes glucose and fatty acids (C) Oxidation and phosphorylation are tightly coupled in it (D) Dinitrophenol has no effect on it

Description : All the following statements about brown adipose tissue are true except (A) It is rich in cytochromes (B) It oxidizes glucose and fatty acids (C) Oxidation and phosphorylation are tightly coupled in it (D) Dinitrophenol has no effect on it

Last Answer : Answer : C

Anyone have any experience with Hip Misalignment?

Description : Anyone have any experience with Hip Misalignment?

Last Answer : answer:Pretty much everyone is uneven, some more than others. If it doesn't cause you any pain I would not think twice about it. It's why when a seemstress does a hem for you they measure from the ... I bet it would make you feel awkward since you only notice this problem if you look at the mirror.

Which of the listed conditions will occur if dirt and grease are allowed to accumulate between the commutator segments of a motor? A. A partial short circuit. B. A dead short circuit. C. Misalignment of the motor shaft. D. Overspeeding of the motor.

Description : Which of the listed conditions will occur if dirt and grease are allowed to accumulate between the commutator segments of a motor? A. A partial short circuit. B. A dead short circuit. C. Misalignment of the motor shaft. D. Overspeeding of the motor.

Last Answer : Answer: A

A switchboard ammeter indicates a reading slightly above 'zero' when the leads are disconnected, this is caused by _____________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. capacitors inside the meter storing charges

Description : A switchboard ammeter indicates a reading slightly above 'zero' when the leads are disconnected, this is caused by _____________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. capacitors inside the meter storing charges

Last Answer : Answer: A

During maintenance of circuit breakers, _______________. A. always smooth roughened contact surfaces with a file B. never pass more than rated breaker current through the overload heater element C. inspect for wear and misalignment of main contacts D. assume heater elements installed are of correct size

Description : During maintenance of circuit breakers, _______________. A. always smooth roughened contact surfaces with a file B. never pass more than rated breaker current through the overload heater element C. ... wear and misalignment of main contacts D. assume heater elements installed are of correct size

Last Answer : Answer: C

The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Description : The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Last Answer : Answer: A

An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Description : An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Last Answer : Answer: A

If a magnetic controller contactor fails to pick up when the coil voltage is applied to the contactor coil, the cause may be _____________. A. overload B. misalignment of the affected contactor contacts C. low spring pressure D. an open contactor coil

Description : If a magnetic controller contactor fails to pick up when the coil voltage is applied to the contactor coil, the cause may be _____________. A. overload B. misalignment of the affected contactor contacts C. low spring pressure D. an open contactor coil

Last Answer : Answer: D

A loud buzzing noise at the contacts of a magnetic controller could indicate _____________. A. weak contact spring pressure B. misalignment of the magnet faces C. excessive line current D. mechanical binding

Description : A loud buzzing noise at the contacts of a magnetic controller could indicate _____________. A. weak contact spring pressure B. misalignment of the magnet faces C. excessive line current D. mechanical binding

Last Answer : Answer: B

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Description : A flange coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : A. Which are perfectly aligned

Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Description : Oldham coupling is used to connect two shafts A. Which are perfectly aligned B. Which are not in exact alignment C. Which have lateral misalignment D. Whose axes intersect at a small angle

Last Answer : C. Which have lateral misalignment

A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Description : A universal coupling is used to connect two shafts A. Which are not in exact alignment B. Which are perfectly aligned C. Whose axes intersect at a small angle D. Have lateral misalignment

Last Answer : C. Whose axes intersect at a small angle

How will you detect that misalignment is the probable cause of excessive vibration?

Description : How will you detect that misalignment is the probable cause of excessive vibration?

Last Answer : 1. Coupling to the driven machine is to be disconnected. 2. The turbine is to be run alone. 3. If the turbine runs smoothly, either misalignment, worn coupling or the driven equipment is the cause of the trouble.

Is coupling loss from angular misalignment more critical in expanded beam or butt-jointed connectors?

Description : Is coupling loss from angular misalignment more critical in expanded beam or butt-jointed connectors?

Last Answer : Expanded beam connectors.

Is coupling loss from fiber separation and lateral misalignment more critical in expanded-beam or butt-jointed connectors?

Description : Is coupling loss from fiber separation and lateral misalignment more critical in expanded-beam or butt-jointed connectors?

Last Answer : Butt-jointed connectors.

How does index matching gel affect the amount of coupling loss caused by (a) fiber separation, (b) lateral misalignment, and (c) angular misalignment?

Description : How does index matching gel affect the amount of coupling loss caused by (a) fiber separation, (b) lateral misalignment, and (c) angular misalignment?

Last Answer : (a) Reduces coupling loss, (b) does not change coupling loss, and (c) increases coupling loss

When the axes of two connected fibers are no longer in parallel, the two connected fibers are in what kind of misalignment?

Description : When the axes of two connected fibers are no longer in parallel, the two connected fibers are in what kind of misalignment?

Last Answer : Angular misalignment.

State types of maintenance. Explain each with example.

Description : State types of maintenance. Explain each with example. 

Last Answer : Maintenance are classified as below:- 1. Preventive Maintenance (PM) 2. Routine /daily maintenance 3. Periodic maintenance/Time based maintenance (TBM) 4. Predictive maintenance (PDM) 5. ... by the manufacturer. It involves partial or complete dismantling of the equipment/machine and overhaul.

Explain importance and purpose of earthing.

Description : Explain importance and purpose of earthing. 

Last Answer : Importance and purpose of earthing is as below:- 1. To provide an alternative path for the leakage current to flow towards earth. 2. To save human life from danger of electrical shock due to ... equipment body (frame) below the earth potential in the event of fault from safety point of view. 

State the methods of Neutral Grounding. State difference between Earthing and grounding.

Description : State the methods of Neutral Grounding. State difference between Earthing and grounding. 

Last Answer : Neutral Grounding connections are of three types:  1. Solid earthing 2. Resistance earthing 3. Reactance earthing SR. NO. Earthing Grounding 1 Earthing means connecting the dead part ... earthing provides suitable means for earth fault protecting system.  10

Classify the insulating materials as per operating temperature. Give two examples of each type.

Description : Classify the insulating materials as per operating temperature. Give two examples of each type.

Last Answer : Sr.No.  Insulation Classes  Maximum permissible temperature (0C) Insulating Material 1 Class-Y or O  900 Cotton, silk, paper, press board, wood, cellulose-, PVC, VIR. (Cotton, silk, ... adhesive coating.  7 Class- C  Over 1800 Porcelain, ceramics, glass, quartz. 

Explain vacuum impregnation method used for Re-varnishing of insulation with neat diagram.

Description : Explain vacuum impregnation method used for Re-varnishing of insulation with neat diagram.

Last Answer : Figure of process of vaccum impregnation:-  Explain the process of vacuum impregnation:- The plant consists of: 1. A large air tight chamber (VIC) i.e. processing or impregnation chamber. 2 ... )curing temperature varies from 90°C to 110°C for 10-20 minutes in some cases one to two hours.

State any eight causes of fire.

Description : State any eight causes of fire. 

Last Answer : Following are the Causes of electrical Fires:- 1. Overloading on cables/wires/machine causes possibility of fire. 2. Use of too many device plugged into a circuit, causing heated wire & possible a ... & equipment's used in hazards area are not used as per the specification/type of protection.

State the basic requirements of foundation for :(i) Static equipment’s (ii) Rotating equipment’s

Description : State the basic requirements of foundation for :(i) Static equipment’s (ii) Rotating equipment’s

Last Answer : Following are the basic requirements of foundation to be considered in designing the machine foundation for :(i) Static equipment's (ii) Rotating equipment's  1. Depth of foundation should be ... it.  11. The dimension of foundation should be proportional to safe bearing capacity of soil.

State the methods used to measure insulation resistance and explain Dielectric Absorption method.

Description : State the methods used to measure insulation resistance and explain Dielectric Absorption method.

Last Answer : There are three types of tests for measuring insulation resistance:  1. Spot test reading or Short Time test  2.Time-resistance test or Dielectric absorption test or Testing methods based on the PI & DAR  3. ... and if value of PI is less than 2 and value of DAR is less than 1.25

State and explain properties of transformer oil.

Description : State and explain properties of transformer oil.  

Last Answer : Following are the properties of transformer oil:-  1. Dielectric strength :- It should be have a high dielectric strength  2. Specific resistance:- It should be have a high Specific ... be not contain impurities such as sulpher & its compounds to avoid rusting & sludge formation. 

List routine tests to be conducted on 3 phase transformer as per 1S-2026-2011.

Description : List routine tests to be conducted on 3 phase transformer as per 1S-2026-2011. 

Last Answer : Following tests are conducted/carried out on Transformer as per IS 2026 Routine tests of transformer include:- 1. Winding resistance measurement.(Both HV and LV winding ) 2. Measurement of ... Tests on on-load tap-changer, where appropriate. 11. To check against leakages through gaskets.

List any four internal causes for abnormal operation of electrical equipment’s.

Description : List any four internal causes for abnormal operation of electrical equipment’s. 

Last Answer : Internal causes:- 1. Open circuit 2. Short circuit 3. Earth fault 4. Loose connection 5. Deposit of dirt and dust near ventilation passage 6. Low insulation resistance 7. Improper maintenance 8. Poor ... problems 13. Failure of cooling system 14. Excess wear and tear of internal parts 15. Ageing.

Prepare troubleshooting chart for transformer as per IS- 10028-1981 (4 trouble) and Induction motor (4 troubles).

Description : Prepare troubleshooting chart for transformer as per IS- 10028-1981 (4 trouble) and Induction motor (4 troubles). 

Last Answer : Troubleshooting chart for I.M. :-  Sr.No Type of fault/abnormal conditions/Troubles Causes Remedies 1 Motor fails to start or not accelerate (Faults in starting supply ... 1.Unequal terminal voltage. 2. Single phase operation 3.Unbalanced voltage Rectify the Cause

State the procedure for developing preventive maintenance schedule.

Description : State the procedure for developing preventive maintenance schedule. 

Last Answer : Procedure of PM is as below:-  Step 1:- Inspection: What to inspect and how to inspect? Maintenance engineer / team should inspect the plan under working condition. Prepare the check ... :- Check the availability of trained & skilled technician to do maintenance before starting the work.

State any eight safety precautions to be followed while working with an electric installation.

Description : State any eight safety precautions to be followed while working with an electric installation. 

Last Answer : Wear safety boot and use right tool for the right job

State the objective of testing. Explain the role of BIS (Bureau of Indian Standards) in testing of electrical machines.

Description : State the objective of testing. Explain the role of BIS (Bureau of Indian Standards) in testing of electrical machines. 

Last Answer : 1. Objective of testing is to finding error/defects in machine/equipment/ product. 2. To confirm whether the results obtain during testing are within tolerance limits specified by BIS / ISS 3. To ... BIS/ISS specified standards. 5. To avoid in convinces & accidents BIS plays important role.  

State any one application of each tool : (i) Earth tester (ii) Megger (iii) Bearing puller (iv) Growler

Description : State any one application of each tool : (i) Earth tester (ii) Megger (iii) Bearing puller (iv) Growler 

Last Answer : i) Earth Tester :- It is used to measure earth resistance.  ii) Megger :- Megger is used to find out (measure) insulation resistance of electrical machine/equipment.  iii) ... is an electrical device used to find out shorted turn faults in armature winding and stator winding of motor.

List any eight contamination agents of the transformer oil.

Description : List any eight contamination agents of the transformer oil. 

Last Answer : The insulating oil gets contaminated when the following impurities are present in oil. 1. Presence of dissolved moisture content. 2. Presence of water content. 3. Presence of dissolved gases ... sulpher content 9. Presence of acetones content. 10. Presence of dissolved oil decay products content

State any four advantages of preventive maintenance.

Description : State any four advantages of preventive maintenance. 

Last Answer : Following are the advantages of Preventive Maintenance:- 1. It increases life of machine/equipment. 2. It prevents premature failure. 3. It keeps the machine in good working condition by reducing wear and ... more expensive than the same job done PM/preplanned (and may take 10 times longer).

State the factors on which severity of electric shock depends.

Description : State the factors on which severity of electric shock depends. 

Last Answer : The severity of shock depends on following factors.  1. Magnitude voltage of the system.  2. The period or duration for which the area of contact with lives part.  3. It is also depends on ... 200mA  May cause fibration of heart  6 Above -200mA Causes death, severe burns 

What cities are unfairly coupled?

Description : What cities are unfairly coupled?

Last Answer : Do they have to be geographically close?

Nikon Manual SLR coupled with AF-S?

Description : Nikon Manual SLR coupled with AF-S?

Last Answer : XCNuse, I gotta think you know a lot more about this that I do The AF-S set of lenses have the auto-focus motor built in to the lens itself. Typically, the camera body itself has the auto-focus motor and ... it has any bearing on aperture at all. - Sits back and waits to find out how wrong he is. ツ

Why oh why can't wisdom automatically be coupled with perceptiveness?

Description : Why oh why can't wisdom automatically be coupled with perceptiveness?

Last Answer : Using the definitions of wisdom arrived at here, wisdom does generally correlate with perceptiveness. As for intelligence, there is such a broad range of traits that can be considered signs of ... blind one to some obvious blunders that a less confident person would be careful to avoid.