If one lamp connects between two phases it will glow or not?

If one lamp connects between two phases it will glow or not?
by

1 Answer

Answer :

If the voltage between the two phases is equal to the lamp voltage then the lamp will glow.
 When the voltage difference is big it will damage the lamp and when the difference is smaller the lamp will glow depending on the type
of lamp.
by

Related questions

If one lamp is connected between two phases will it glow or not?

Description : If one lamp is connected between two phases will it glow or not?

Last Answer : A:If the voltage between the two phase is equal to the lamp voltage then the lamp will glow. When the voltage difference is big it will damage the lamp and when the difference is smaller the lamp will glow depending on the type of lamp.

If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Description : If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Last Answer :  Each bulb when independently working will have currents (W/V= I)  For 200 Watt Bulb current (I200) =200/230=0.8696 A  For 100 Watt Bulb current (I100) =100/230=0.4348 A  ... current through it. So minimum power dissipated across it as min current X equal Voltage across =s min power dissipation

A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. A. the dark lamp must be replaced B. there is a ground in the line with the dark lamp C. there are grounds in two of the three phases D. the voltage to the dark lamp is less than that of the system

Description : A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. ... of the three phases D. the voltage to the dark lamp is less than that of the system

Last Answer : Answer: A

At what points along a transmission line will a neon lamp glow the brightest?

Description : At what points along a transmission line will a neon lamp glow the brightest?

Last Answer : At standing-wave voltage peaks.

Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively are connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : A:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Description : Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Last Answer : Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the Bulb (P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

A burned-out LED should be indicated by _____________. A. excessive output B. a slight glow in the crystal C. excessive illumination D. no illumination

Description : A burned-out LED should be indicated by _____________. A. excessive output B. a slight glow in the crystal C. excessive illumination D. no illumination

Last Answer : Answer: D

An electric bulb is connected on a holder. One end of the wire is connected to the phase and the remaining one connected to earth instead of neutral. The bulb will glow or not? If yes then what is the need of neutral?

Description : An electric bulb is connected on a holder. One end of the wire is connected to the phase and the remaining one connected to earth instead of neutral. The bulb will glow or not? If yes then what is the need of neutral?

Last Answer : 1. Yes the bulb will be glow & neutral is return path of Circuit it is originated from distribution transformers star point, form this point only neutral is taken. 2. Then what is the need ... : It gives assurance of reliable centralized earthling as your home may or may not have reliable earthling.

As shown in the illustration, what is the meaning of the numbers in brackets [ ] at location '31/33U'? EL-0100 A. Four separate devices with these part numbers feed signals into this point. B. There is a 33 kOhm bridge resistor at each of these locations in the wheelhouse. C. Wire '33K' continues on those four pages and connects to devices at the indicated coordinates. D. None of the above.

Description : As shown in the illustration, what is the meaning of the numbers in brackets [ ] at location '31/33U'? EL-0100 A. Four separate devices with these part numbers feed signals into this point. ... continues on those four pages and connects to devices at the indicated coordinates. D. None of the above.

Last Answer : Answer: C

Why three phases? Why not one or two or four?

Description : Why three phases? Why not one or two or four?

Last Answer : In 1-phase and 2-phase power, there are 120 moments per second when a sine wave is crossing zero volts. In 3-phase power, at any given moment one of the three phases is nearing a peak. ... would not significantly improve things but would add a fourth wire, so 3-phase is the natural settling point.

As shown in the illustration, which of the listed actions of the synchroscope pointer is occurring? EL-0002 A. Revolving slowly in the slow direction. B. Revolving rapidly in the slow direction. C. Revolving rapidly in the fast direction. D. It would be stationary at the 12 o'clock position since the leading edges of the A phases are in phase.

Description : As shown in the illustration, which of the listed actions of the synchroscope pointer is occurring? EL-0002 A. Revolving slowly in the slow direction. B. Revolving rapidly in the slow direction. C. ... stationary at the 12 o'clock position since the leading edges of the A phases are in phase.

Last Answer : Answer: C

In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a slight ground on all three phases B. the switch must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Description : In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a ... must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Last Answer : Answer: C

If all of the ground detection lamps burn with equal brilliance, whether the test button is depressed or released, then ___________. A. no grounds exist B. all phases are grounded C. all lamps show a ground D. all of the above

Description : If all of the ground detection lamps burn with equal brilliance, whether the test button is depressed or released, then ___________. A. no grounds exist B. all phases are grounded C. all lamps show a ground D. all of the above

Last Answer : Answer: A

When paralleled, AC generators must have the same _________. A. frequency B. number of phases C. phase rotation D. all of the above

Description : When paralleled, AC generators must have the same _________. A. frequency B. number of phases C. phase rotation D. all of the above

Last Answer : Answer: D

If all three ground-detection lamps continue to burn at equal intensity after the test button is depressed and released, which of the listed conditions is indicated? A. No grounds exist B. All three phases are grounded C. The test switch is faulty D. The current transformers are shorted out

Description : If all three ground-detection lamps continue to burn at equal intensity after the test button is depressed and released, which of the listed conditions is indicated? A. No grounds exist B. All three phases are grounded C. The test switch is faulty D. The current transformers are shorted out

Last Answer : Answer: A

Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on different phases will not cause an outage. C. Ground detection systems are unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Description : Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on ... unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Last Answer : Answer: A

A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Description : A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Last Answer : Answer: B

If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of an open motor lead B. the 'Disc.sw.' is open C. power to 'L1' at the 'Disc.sw.' is not energized because of a problem with the ship's electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Description : If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of ... electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Last Answer : Answer: A

Which of the following procedures should be used to determine the load of a threephase, delta wound, AC generator? A. Multiply the amperage in one phase by three. B. Divide the total amperage in all phases by three. C. Multiply the amperage in one phase by the square root of three. D. Divide the total amperage in all phases by the square root of three.

Description : Which of the following procedures should be used to determine the load of a threephase, delta wound, AC generator? A. Multiply the amperage in one phase by three. B. Divide the total amperage in all ... square root of three. D. Divide the total amperage in all phases by the square root of three.

Last Answer : Answer: C

On a switchboard, if all three ground detection lamps remain burning at half intensity when the test button is depressed, which of the listed conditions is indicated? A. No grounds exist. B. All three phases are grounded. C. The test switch is grounded. D. The current transformers are shorted.

Description : On a switchboard, if all three ground detection lamps remain burning at half intensity when the test button is depressed, which of the listed conditions is indicated? A. No grounds exist. B. All three phases are grounded. C. The test switch is grounded. D. The current transformers are shorted.

Last Answer : Answer: A

The speed of a three-phase squirrel-cage induction-type motor operating in a fixed frequency system is varied by changing the _____________. A. number of phases to the motor B. number of stator poles C. locked rotor current D. resistance of the rotor winding

Description : The speed of a three-phase squirrel-cage induction-type motor operating in a fixed frequency system is varied by changing the _____________. A. number of phases to the motor B. number of stator poles C. locked rotor current D. resistance of the rotor winding

Last Answer : Answer: B

Which of the following statements is true concerning all three-phase alternators? A. Each has three separate but identical armature windings acted on by one system of rotating magnets. B. Each has one armature winding acted on by three identical but separate systems of rotating magnets. C. All three-phase alternators are designed to operate with a 0.8 leading power factor. D. The three phases always provide power to the load through three sets of slip rings and brushes.

Description : Which of the following statements is true concerning all three-phase alternators? A. Each has three separate but identical armature windings acted on by one system of rotating magnets. B. Each has one ... The three phases always provide power to the load through three sets of slip rings and brushes.

Last Answer : Answer: A

A degree of control over the speed of a slip ring induction motor can be obtained by _____________. A. adjusting governor linkage B. changing the number of phases to the motor C. inserting resistance into the stator circuit D. inserting resistance into the rotor circuit

Description : A degree of control over the speed of a slip ring induction motor can be obtained by _____________. A. adjusting governor linkage B. changing the number of phases to the motor C. inserting resistance into the stator circuit D. inserting resistance into the rotor circuit

Last Answer : Answer: D

What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Description : What current is required to light two 75 watt lamps and one 40 watt lamp when connected in series to a 120 volt power source? A. 0.161 amperes B. 0.631 amperes C. 1.583 amperes D. 6.199 amperes

Last Answer : Answer: C

A flickering ground detection lamp on a DC system would indicate a _____________. A. multiple-ground condition in the distribution system B. ground in an armature coil of an operating machine C. ground in a motor accompanied with a short D. short between two adjacent bars of the generator commutator

Description : A flickering ground detection lamp on a DC system would indicate a _____________. A. multiple-ground condition in the distribution system B. ground in an armature coil of an operating machine C. ground in a motor accompanied with a short D. short between two adjacent bars of the generator commutator

Last Answer : Answer: B

The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and 'C' will burn brightly B. normally, and lamps 'B' and 'C' will burn dimly or be out C. brightly, and lamps 'B' and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Description : The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and ... and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Last Answer : Answer: A

When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Description : When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Last Answer : Answer: A

A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms

Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms

Last Answer : Answer: D

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Last Answer : Answer: D

In a three-phase electrical system, three ground detecting lamps are provided. One lamp goes dark and the others increase in brightness. When the test button is pushed, all lamps have equal illumination. You should conclude that ____________. A. there is a ground on the line with the dark lamp B. the dark lamp must be replaced C. there are grounds on the lines with the bright lamps D. this is a normal condition

Description : In a three-phase electrical system, three ground detecting lamps are provided. One lamp goes dark and the others increase in brightness. When the test button is pushed, all lamps have equal illumination. You ... C. there are grounds on the lines with the bright lamps D. this is a normal condition

Last Answer : Answer: A

When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Description : When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Last Answer : Answer: D

In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. the brushes should be set back on the commutator and the test redone C. the ground is not in the windings and the connections to the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Description : In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. ... the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Last Answer : Answer: C

The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Description : The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Last Answer : Answer: D

A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Description : A current-carrying conductor makes accidental contact with a wiring conduit. This will be indicated by a _____________. A. low switchboard wattmeter reading B. high switchboard wattmeter reading C. darkened switchboard ground detecting lamp D. darkened switchboard synchronizing lamps

Last Answer : Answer: C

When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, causing glass to fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Description : When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, ... fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Last Answer : Answer: D

In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three lamps will return to their normal brightness indicating that the bulbs are not burnt out C. lamps B and C will dim lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Description : In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three ... lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Last Answer : Answer: B

An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This means _____________. A. there is a ground on the phase with the dark lamp B. the phase sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Description : An AC generator panel is fitted with both synchronizing lamps and a synchroscope. When the synchroscope pointer reaches the noon position, one synchronizing light is bright and the other is dark. This ... sequence is incorrect C. the phase sequence is correct D. the generator breaker may be closed

Last Answer : Answer: B

In the illustration, 'D' is the symbol for a/an __________. EL-0005 A. thermal overload heater B. portable cable C. fuse D. indicating lamp

Description : In the illustration, 'D' is the symbol for a/an __________. EL-0005 A. thermal overload heater B. portable cable C. fuse D. indicating lamp

Last Answer : Answer: C

Four lamps are connected in parallel in a single circuit. If one of the lamp burns out, the others will _____________. A. all go out B. become dimmer C. burn with their original intensities D. become brighter

Description : Four lamps are connected in parallel in a single circuit. If one of the lamp burns out, the others will _____________. A. all go out B. become dimmer C. burn with their original intensities D. become brighter

Last Answer : Answer: C

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Description : Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Last Answer : Answer: C