Consider the following statements: Mitra’s hyperbolic transition design is based on the principle that : 1. Flow depth in the canal, as well as the discharge, is constant 2. width of the canal varies along with the discharge 3. Rate of change of velocity per unit length of transition is constant throughout the length of the transition. Which of these statements are correct ? a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Consider the following statements:
 Mitra’s hyperbolic transition design is based on the principle that :
1. Flow depth in the canal, as well as the discharge, is constant
2. width of the canal varies along with the discharge
3. Rate of change of velocity per unit length of transition is constant throughout the length of the transition.
Which of these statements are correct ?
a) 1, 2 and 3 b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only
by

1 Answer

Answer :

d) 1 and 3 only
by

Related questions

Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the centre of the pipe. 4. Hydraulic gradient varies as the square of the mean velocity of flow. Which of these statements are correct? (a) 1, 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Description : Consider the following statements in respect of steady laminar flow through a circular pipe: 1. Shear stress is zero on the central axis of the pipe 2. Discharge varies directly with the viscosity of the fluid 3. Velocity is maximum at the ... 2 , 3 & 4 (b) 1 & 3 only (c) 2 & 4 only (d)3 & 4 only

Last Answer : (b) 1 & 3 only

Consider the following statements: The time of BOD assimilation in a stream can be affected by 1. Ratio of stream depth to flow width. 2. Stream BOD value 3. BOD rate constant. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: The time of BOD assimilation in a stream can be affected by 1. Ratio of stream depth to flow width. 2. Stream BOD value 3. BOD rate constant. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (a) 1, 2 & 3

If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Description : If the velocities of flow of a stream of 10 m depth recorded by a current meter at depths of 2 m and 8 m are 0.7 m and 0.3 m respectively, the discharge per unit width of the stream in cubic metres, is (A) 2 (B) 3 (C) 4 (D) 5

Last Answer : Answer: Option D

According to Bernoulli's equation for steady ideal fluid flow (A) Principle of conservation of mass holds (B) Velocity and pressure are inversely proportional (C) Total energy is constant throughout (D) The energy is constant along a streamline but may vary across streamlines

Description : According to Bernoulli's equation for steady ideal fluid flow (A) Principle of conservation of mass holds (B) Velocity and pressure are inversely proportional (C) Total energy is constant throughout (D) The energy is constant along a streamline but may vary across streamlines

Last Answer : Answer: Option D

Consider the following statements : 1. There is no flow across a streamline 2. Streamline spacing varies directly with velocity at the section 3. Streamlines do not cross 4. In steady flow, streamline pattern does not change with time Which of these statements in respect of stream flow pattern are correct? (a) 1, 2, 3 and 4 (b) 1 and 2 only (c) 1, 3 and 4 only (d) 2, 3 and 4 only

Description : Consider the following statements : 1. There is no flow across a streamline 2. Streamline spacing varies directly with velocity at the section 3. Streamlines do not cross 4. In steady flow, streamline pattern does not change with ... 4 (b) 1 and 2 only (c) 1, 3 and 4 only (d) 2, 3 and 4 only

Last Answer : (c) 1, 3 and 4 only

Consider the following assumption made in the analysis of a jet impinging normally on a moving plate to introduce the principle of moment of momentum: 1. Friction between jet and plate is neglected. 2. Flow is steady 3. Impinging momentum of jet is uncharged. 4. Plate moves at a constant velocity. Which of these statements are relevant? (a) 1, 2 & 4 only (b) 1, 2 & 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 & 4

Description : Consider the following assumption made in the analysis of a jet impinging normally on a moving plate to introduce the principle of moment of momentum: 1. Friction between jet and plate is neglected. 2. Flow is steady 3. Impinging momentum of ... b) 1, 2 & 3 only (c) 2, 3 and 4 only (d) 1, 2, 3 & 4

Last Answer : (a) 1, 2 & 4 only

The sewage discharge in a detritus tank of a treatment plant is 576 litres/sec with flow velocity of 0.2 m/sec. If the ratio of width to depth is 2, the depth is A. 100 cm B. 110 cm C. 120 cm D. 150 cm

Description : The sewage discharge in a detritus tank of a treatment plant is 576 litres/sec with flow velocity of 0.2 m/sec. If the ratio of width to depth is 2, the depth is A. 100 cm B. 110 cm C. 120 cm D. 150 cm

Last Answer : ANS: C

In a sedimentation tank (length L, width B, depth D) the settling velocity of a particle for a discharge Q, is A. Q/(B × D) B. Q/(L × D) C. Q/L D. Q/(B × L)

Description : In a sedimentation tank (length L, width B, depth D) the settling velocity of a particle for a discharge Q, is A. Q/(B × D) B. Q/(L × D) C. Q/L D. Q/(B × L)

Last Answer : ANS: D

The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Description : The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Last Answer : (A) Parabolic

The radius of curvature provided along a transition curve, is (A) Minimum at the beginning (B) Same throughout its length (C) Equal to the radius of circular curve (D) Varying from infinity to the radius of circular curve

Description : The radius of curvature provided along a transition curve, is (A) Minimum at the beginning (B) Same throughout its length (C) Equal to the radius of circular curve (D) Varying from infinity to the radius of circular curve

Last Answer : Answer: Option D

The dimensions of a rectangular settling tank are: length 24 m, width 6 m and depth 3 m. If 2 hour detention period for tanks is recommended, the rate of flow of sewage per hour, is A. 204 cu.m B. 208 cu.m C. 212 cu.m D. 216 cu.m

Description : The dimensions of a rectangular settling tank are: length 24 m, width 6 m and depth 3 m. If 2 hour detention period for tanks is recommended, the rate of flow of sewage per hour, is A. 204 cu.m B. 208 cu.m C. 212 cu.m D. 216 cu.m

Last Answer : ANS: D

Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) The rate of flow of water through a vertical strip of the aquifer of unit width and full depth under a unit hydraulic gradient, is called coefficient of transmissibility (C) The flow of water through aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Description : Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) ... aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Last Answer : Answer: Option D

Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a given discharge. 4. The Froude number is equal to unity. Which of these statements are correct? (a) 1 , 2 & 3 only (b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Description : Consider the following statements in respect of critical flow in a wide rectangular channel: 1. The specific energy is minimum for a given discharge. 2. The discharge is maximum for a given specific energy 3. The specific force is minimum for a ... b) 1, 2, 3 & 4 (c) 1, 2 & 4 only (d) 2, 3 & 4 only

Last Answer : (b) 1, 2, 3 & 4

Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water (F.S.D.) (B) Area of canal in cutting = BD + Sd 2 where B = bed width, d = depth of cutting and S is the side slope (C) If F.S.L. is above N.S.L the canal is called partly in cutting and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Description : Pick up the correct statement from the following: (A) If the bed level is above N.S.L. the canal is called fully in baking and the berms are designed as 3 d where d is full supply depth of water ... and partly in filling and berms are designed as 2d where d is full supply depth (D) All the above

Last Answer : (D) All the above

For steady ideal fluid flow, the Bernoulli's equation states that the (A) Velocity is constant along a stream line (B) Energy is constant throughout the fluid (C) Energy is constant along a stream line, but may vary across stream lines (D) None of these

Description : For steady ideal fluid flow, the Bernoulli's equation states that the (A) Velocity is constant along a stream line (B) Energy is constant throughout the fluid (C) Energy is constant along a stream line, but may vary across stream lines (D) None of these

Last Answer : (C) Energy is constant along a stream line, but may vary across stream lines

The discharge per unit plan area of a sedimentation tank, is generally called A. Over flow rate B. Surface loading C. Over flow velocity D. All the above

Description : The discharge per unit plan area of a sedimentation tank, is generally called A. Over flow rate B. Surface loading C. Over flow velocity D. All the above

Last Answer : ANS: D

The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end

Last Answer : (C) Varies exponentially, being more near the torque-input end

In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as the (A) Square root of the velocity (B) Square of the viscosity (C) Filtration time only (D) Washing time only

Description : In continuous filtration (at a constant pressure drop), filtrate flow rate varies inversely as the (A) Square root of the velocity (B) Square of the viscosity (C) Filtration time only (D) Washing time only

Last Answer : (A) Square root of the velocity

If L, B and D length, breadth and depth of water in a rectangular sedimentation tank of total discharge Q, the settling velocity, is (A) Q/H(B) Q/D(C) Q/(D × B) (D) Q/(L × B)

Description : If L, B and D length, breadth and depth of water in a rectangular sedimentation tank of total  discharge Q, the settling velocity, is  (A) Q/H (B) Q/D (C) Q/(D × B)  (D) Q/(L × B) 

Last Answer : (D) Q/(L × B) 

If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Description : If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Last Answer : Answer: Option B

Consider the following statements The general depth of scour calculated by Lacey’s formula in a river represents the depth below the: 1. Maximum flood level in the river 2. Minimum flow water level in the river 3. Normal flow water level in the river 4. Existing river bed level Which of these statements is/are correct ? a) 1, 2, 3 and 4 b) 1, 2 and 3 only c) 2, 3 and 4 only d) 1 only

Description : Consider the following statements The general depth of scour calculated by Lacey's formula in a river represents the depth below the: 1. Maximum flood level in the river 2. Minimum flow water level in the river 3. Normal flow water ... 2, 3 and 4 b) 1, 2 and 3 only c) 2, 3 and 4 only d) 1 only

Last Answer : d) 1 only

Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Description : Slenderness ratio of the column is the ratio of [ A ] the effective length to width of column [ B ] the effective length to depth of column [ C ] the effective length to least lateral design [ D ] none of the above

Last Answer : [ C ] the effective length to least lateral design

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Description : According to Chezy's formula, the discharge through an open channel is (where A = Area of flow, C = Chezy's constant, m = Hydraulic mean depth, and i = Uniform slope in bed) (A) A × m × i) (B) C × m × i) (C) AC × m × i) (D) mi × A × C)

Last Answer : Answer: Option C

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

A depth-discharge relationship of the canal section is maintained at a notch fall because the sill of the notches is : a) Level with downstream canal bed b) Below the upstream canal bed c) Level with upstream canal bed d) Above the upstream canal bed

Description : A depth-discharge relationship of the canal section is maintained at a notch fall because the sill of the notches is : a) Level with downstream canal bed b) Below the upstream canal bed c) Level with upstream canal bed d) Above the upstream canal bed

Last Answer : c) Level with upstream canal bed

The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Last Answer : (B) 3WL/2fd²

The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom (C) The sloping side is equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Description : The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom ... equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Last Answer : Answer: Option C

Consider the following statements. Morphological characteristics of a river are represented by : 1. Changes in the river form 2. Changes in the characteristics of the river bed s a result of variation of discharge in the river 3. No change in the river plan form Which of these statements are correct ? a) 1 and 2 b) 1 and 3 c) 2 and 3 d) 3 and 4

Description : Consider the following statements. Morphological characteristics of a river are represented by : 1. Changes in the river form 2. Changes in the characteristics of the river bed s a result of variation of discharge in the river 3. No ... are correct ? a) 1 and 2 b) 1 and 3 c) 2 and 3 d) 3 and 4

Last Answer : a) 1 and 2

A compound pipe is required to be replaced by a new pipe. The two pipes are said to be equivalent, if (A) Length of both the pipes is same (B) Diameter of both the pipes is same (C) Loss of head and discharge of both the pipes is same (D) Loss of head and velocity of flow in both the pipes is same

Description : A compound pipe is required to be replaced by a new pipe. The two pipes are said to be equivalent, if (A) Length of both the pipes is same (B) Diameter of both the pipes is same (C) Loss of ... discharge of both the pipes is same (D) Loss of head and velocity of flow in both the pipes is same

Last Answer : Answer: Option C

Specific yield of well is a) Discharge per unit time b) Yield of well per metre of drawdown* c) Velocity of water per unit time d)None of the above

Description : Specific yield of well is a) Discharge per unit time b) Yield of well per metre of drawdown* c) Velocity of water per unit time d)None of the above

Last Answer : b) Yield of well per metre of drawdown*

For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance(D) Elevation along vertical direction

Description : For a fluid rotating at constant angular velocity about vertical axis as a rigid body, the pressure intensity varies as the (A) Square of the radial distance (B) Radial distance linearly (C) Inverse of the radial distance (D) Elevation along vertical direction

Last Answer : (A) Square of the radial distance

Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of these statements are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Description : Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of ... are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Last Answer : d) 1 and 3 only

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

Assertion A: Depth and width required at the entrance to a harbour are more than those required in the channel. Reason R: The entrance to a harbour is usually more exposed to waves as compared to the harbour itself. Select your answer based on the coding system given below: (A) Both A and R is true and R is the correct explanation of A (B) Both A and R is true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Description : Assertion A: Depth and width required at the entrance to a harbour are more than those required in the channel. Reason R: The entrance to a harbour is usually more exposed to waves as compared to the harbour itself. ... explanation of A (C) A is true but R is false (D) A is false but R is true

Last Answer : (A) Both A and R is true and R is the correct explanation of A

Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep foundation (C) If the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Description : Pick up the correct statement from the following: (A) If the ratio of depth to width is less than 2, it is shallow foundation (B) If the ratio of depth to width is more than 2, it is deep ... the ratio of the length to width is between 1 and 2, it is spread foundation (D) All the above

Last Answer : Answer: Option D

Uniform flow occurs when (A) The flow is steady (B) The flow is streamline (C) Size and shape of the cross section in a particular length remain constant (D) Size and cross section change uniformly along length

Description : Uniform flow occurs when (A) The flow is steady (B) The flow is streamline (C) Size and shape of the cross section in a particular length remain constant (D) Size and cross section change uniformly along length

Last Answer : Answer: Option C

he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe at the same flow rate/average velocity, then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Description : he pressure drop per unit length of pipe incurred by a fluid 'X' flowing through pipe is Δp. If another fluid 'Y' having both the specific gravity & density just double of that of fluid 'X', flows through the same pipe ... then the pressure drop in this case will be (A) Δp (B) 2Δp (C) Δp 2 (D) Δp/2

Last Answer : (B) 2Δp

Which of the following canal outlets maintains a constant discharge? (A) Non-modular outlet (B) Flexible outlet (C) Rigid module (D) None of the above

Description : Which of the following canal outlets maintains a constant discharge? (A) Non-modular outlet (B) Flexible outlet (C) Rigid module (D) None of the above

Last Answer : Answer: Option C

In an ideal P.F.R. at steady state conditions (A) The composition of reactants remains constant along a flow path (B) The conversion of the reactant varies from point to point along a flow path (C) There is no lateral mixing of fluid (D) There may be diffusion along the flow path

Description : In an ideal P.F.R. at steady state conditions (A) The composition of reactants remains constant along a flow path (B) The conversion of the reactant varies from point to point along a flow path (C) There is no lateral mixing of fluid (D) There may be diffusion along the flow path

Last Answer : (B) The conversion of the reactant varies from point to point along a flow path

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Description : As per Taggart's formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms). (A) LS (B) 93 LS (C) 250 LS (D) √(LS)

Last Answer : (B) 93 LS

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Description : Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Last Answer : (A) Varies parabolically across the section

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

For a homogeneous earth dam 50 m high having 2 m free broad, a flow net was constructed and the results were : Number of potential drops = 2.4 Number of flow channels = 0.4. If co-efficiency of permeability of the dam material is 3 × 10-3 cm3 /sec, the discharge per metre length of dam, is (A) 12 × 10-5 m3 /sec (B) 24 × 10-3 m3 /sec (C) 6 × 10-5 m3 /sec (D) 24 × 10-5 m3 /sec

Description : For a homogeneous earth dam 50 m high having 2 m free broad, a flow net was constructed and the results were : Number of potential drops = 2.4 Number of flow channels = 0.4. If co-efficiency of permeability of the dam material is ... 24 10-3 m3 /sec (C) 6 10-5 m3 /sec (D) 24 10-5 m3 /sec

Last Answer : (D) 24 × 10-5 m3 /sec