Description : The graphical method of Mohr's circle represents shear stress (τ) on ______ a. X-axis b. Y-axis c. Z-axis d. None of the above
Last Answer : b. Y-axis
Description : Mohr’s stress circle is named so because it has equation of the form a. x^2 + y^2 = r^2 b. (x-a)^2 + y^2 = r^2 c. (x-a)^2 + (y-b)^2 = r^2 d. It was desired by German Engineer Otto Mohr
Last Answer : b. (x-a)^2 + y^2 = r^2
Description : In Mohr’s circle of strain, y-axis represents a. Shear strain b. Half of shear strain c. Normal strain d. Half of normal strain
Last Answer : b. Half of shear strain
Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above
Last Answer : c. Principal stress
Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse
Last Answer : b) Square
Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress
Last Answer : 3. tensile stress
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above
Last Answer : (A) shot peening
Description : Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x - σ y )/2 ]sin θ - τ cos 2θ b. [(σ x - ... τ cos 2θ c. [(σ x - σ y )/2 ]sin θ - τ 2 cos θ d. None of the above
Last Answer : c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ
Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None
Last Answer : (i) Shear stress
Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress
Last Answer : (iii) Tensile stress
Description : Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress
Description : The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress
Last Answer : (c) fluctuating stress
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress
Last Answer : (C) Twice of shear stress
Description : A principal stress is a. Tensile or shear stress b. Compressive or shear stress c. Tensile or compressive stress d. None
Last Answer : c. Tensile or compressive stress
Description : The principal strain due to σ1(tensile) and σ2 (Compressive ) stress is (a) Firstly (b)Secondly (c)Thirdly (d) None
Last Answer : (b)Secondly
Description : A complementary shear stress is equal in magnitude and opposite in rotational tendency of an applied (a) Tensile stress (b) Compressive stress (c) Shear stress (d) None
Last Answer : (c) Shear stress
Description : Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None
Last Answer : (c) Compressive stress
Description : A principal plane is a plane of (a) Zero tensile stress (b) Zero compressive stress (c) Zero shear stress (d) None
Last Answer : (c) Zero shear stress
Description : The equations for principal stresses are valid only when (a)σ x and σ y are both tensile (b) σ x is compressive and σ y is tensile (c) σ x is tensile and σ y is compressive (d) None
Last Answer : (a)σ x and σ y are both tensile
Description : The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses
Last Answer : d) Reversed Stresses
Description : The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses
Last Answer : a) Alternating Stresses
Description : The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses
Last Answer : a) Fluctuating Stresses
Description : The stress represented by sin (t) + 1 belongs to which category? a) Fluctuating Stresses b) Alternating stresses c) Repeated Stresses d) Reversed Stresses
Last Answer : c) Repeated Stresses
Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Last Answer : Answer: C
Description : As per IS: 456, permissible direct compressive stress M20 grade concrete in working stress method of designer [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20.0 N/mm2
Last Answer : [ A ] 5.0 N/mm2
Description : The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these
Last Answer : B. Zero at the point other than centroidal axis
Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above
Last Answer : b. Soderberg line
Description : The bending stress in a curved beam is (A) Zero at the centroidal axis (B) Zero at the point other than centroidal axis (C) Maximum at the neutral axis (D) None of these
Last Answer : (B) Zero at the point other than centroidal axis
Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress
Last Answer : (A) Direct tensile stress and bending stress
Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C
Last Answer : (A) (4C - 1/4C - 4) + 0.615/C
Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above
Last Answer : b. intensity of direct stress
Description : Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be ... acting on the connected members should be neither positive nor negative d. None of the above
Last Answer : a. Force acting on the connected members should be negative
Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed
Last Answer : a) Positive
Description : Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None
Last Answer : A. Positive
Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30
Last Answer : a) X=30 Y=18
Description : The magnitude of maximum principal stress is a. Firstly (σ x +σ y )/2+ (1/2)( σ x +σ y ) +4τ 2 ) 5 b. Secondly (σ x +σ y )/2+ (1/2)( σ x -σ y ) 2 +4τ 2 ) 5 c. Thirdly (σ x +σ y )/2+ (1/2)( σ x +σ y ) 2 +4τ 2 ) 5 d. None
Last Answer : b. Secondly (σ x +σ y )/2+ (1/2)( σ x -σ y ) 2 +4τ 2 ) 5
Description : A proton is moving along the negative direction of X-axis in a magnetic field directed along the positive direction of Y-axis. The proton will be defl
Last Answer : A proton is moving along the negative direction of X-axis in a magnetic field directed along the positive ... Y-axis C. Z-axis D. None of these
Description : The Mohr's straight theory is based on the following fact: (A) Material fails essentially by shear (B) Ultimate strength of the material is determined by the stress in the plane of slip (C) Failure criterion is independent of the intermediate principal stress (D) All the above
Last Answer : Answer: Option D
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile