Which among the following is the condition to avoid separation of connected members? a. Force acting on the connected members should be negative b. Force acting on the connected members should be positive c. Force acting on the connected members should be neither positive nor negative d. None of the above

Which among the following is the condition to avoid separation of connected members?

a. Force acting on the connected members should be negative

b. Force acting on the connected members should be positive

c. Force acting on the connected members should be neither positive nor negative

d. None of the above
by

1 Answer

Answer :

a. Force acting on the connected members should be negative
by

Related questions

For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Last Answer : b) False

Which of the following doesn’t waste energy? a) Flywheel b) Governor c) Both flywheel and governor d) Neither flywheel nor governor

Description : Which of the following doesn’t waste energy? a) Flywheel b) Governor c) Both flywheel and governor d) Neither flywheel nor governor

Last Answer : a) Flywheel

A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Last Answer : a) Hub

A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Description : A sunk key fits in the keyway of the _____ only. a) Hub b) Sleeve c) Both hub and sleeve d) Neither hub nor sleeve

Last Answer : a) Hub

If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Last Answer : a) Dog Point

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Cyanobacteria have A-a gram-positive cell wall B- a gram-negative cell wall C- Neither (a) nor (b) D-No cell wall

Description : Cyanobacteria have A-a gram-positive cell wall B- a gram-negative cell wall C- Neither (a) nor (b) D-No cell wall

Last Answer : a gram-negative cell wall

If one premise is negative the conclusion must be________. A) Negative B) Positive C) Both negative and positive D) Neither negative nor positive.

Description : If one premise is negative the conclusion must be________. A) Negative B) Positive C) Both negative and positive D) Neither negative nor positive. 

Last Answer : A) Negative 

A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When installing the new meter it should be __________. A. grounded to the negative side B. connected to a large resistor between the positive side and the ground C. installed exactly as the old installation D. grounded to the positive side

Description : A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When ... side and the ground C. installed exactly as the old installation D. grounded to the positive side

Last Answer : Answer: C

The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed

Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed

Last Answer : a) Positive

Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None

Description : Sunk key is a .............. drive. A. Positive B. Negative C. Neutral D. None

Last Answer : A. Positive

The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed

Description : The main advantage of sunk key is that it is a _____ drive. a) Positive b) Negative c) Neutral d) None of the listed

Last Answer : a) Positive

In Mohr's circle method, compressive direct stress is represented on ____ a. positive x-axis b. positive y-axis c. negative x-axis d. negative y-axis

Description : In Mohr's circle method, compressive direct stress is represented on ____ a. positive x-axis b. positive y-axis c. negative x-axis d. negative y-axis

Last Answer : c. negative x-axis

Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Description : Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Last Answer : 1. avoid cooling stress

If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Description : If the positive and negative shear force diagram areas are not equal, it can be concluded that a.shear force diagram has been wrongly drawn b.there is at least one couple acting on the beam c.107 dynes d.there are at least two maxima for bending moment e.bending moment does not change sign

Last Answer : b. there is at least one couple acting on the beam

Separation of isotopes is generally done using a/an __________ centrifuge. (A) Ultra (B) Disk-bowl (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Separation of isotopes is generally done using a/an __________ centrifuge. (A) Ultra (B) Disk-bowl (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (A) Ultra

Steam distillation is used for separation of high boiling (A) Substances from non-volatile impurities (B) Volatile impurity from still higher boiling substances (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Steam distillation is used for separation of high boiling (A) Substances from non-volatile impurities (B) Volatile impurity from still higher boiling substances (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

An ideal nozzle design aims at (A) Minimising wall friction (B) Suppressing boundary layer separation (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : An ideal nozzle design aims at (A) Minimising wall friction (B) Suppressing boundary layer separation (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False

Description : For two springs connected in parallel, net force is equal to the sum of force in each spring. a) True b) False

Last Answer : a) True

Shear stress in the beam acting on the cross section is (a) Normal to the cross section (b) Tangential to the cross section (c) Neither normal nor tangential (d) None

Description : Shear stress in the beam acting on the cross section is (a) Normal to the cross section (b) Tangential to the cross section (c) Neither normal nor tangential (d) None

Last Answer : b) Tangential to the cross section

If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but governor will not operate (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Description : If the load on the engine is constant, the mean speed will be constant from the cycle, then (A) The governor will not operate but flywheel will be acting (B) The flywheel will be acting but ... (C) Both flywheel and governor will be acting (D) Both flywheel and governor will not be acting

Last Answer : (A) The governor will not operate but flywheel will be acting

The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm<5 (c) rotating at rpm<10 (d) rotating at rpm<15

Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm

Last Answer : (a) stationary

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Hydrodynamic bearing is a self-acting bearing. a) True b) False

Description : Hydrodynamic bearing is a self-acting bearing. a) True b) False

Last Answer : a) True

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Last Answer : b. intensity of direct stress

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

Principal stress is the magnitude of ________ stress acting on the principal plane. a. Normal stress b. Shear stress c. Both a. and b. d. None of the above

Description : Principal stress is the magnitude of ________ stress acting on the principal plane. a. Normal stress b. Shear stress c. Both a. and b. d. None of the above

Last Answer : a. Normal stress

Negative skin friction (A) Is a downward drag acting on a pile due to downward movement of the surrounding compressible soil relative to the pile (B) Develops due to lowering of ground water (C) Both (a) and (b) (D) Neither (a) not (b)

Description : Negative skin friction (A) Is a downward drag acting on a pile due to downward movement of the surrounding compressible soil relative to the pile (B) Develops due to lowering of ground water (C) Both (a) and (b) (D) Neither (a) not (b)

Last Answer : Answer: Option C

What do you call energy from separation of positive and negative charges?

Description : What do you call energy from separation of positive and negative charges?

Last Answer : Need answer

Facts means and include a) Any thing, state of things, or relation of things, capable of being perceived by the senses b) Any mental condition of which any person is conscious. c) Both the A and B d) Neither A nor B

Description : Facts means and include a) Any thing, state of things, or relation of things, capable of being perceived by the  senses b) Any mental condition of which any person is conscious. c) Both the A and B d) Neither A nor B

Last Answer : c) Both the A and B

Safe condition for storage of high V.M. bituminous coal is that (A) Height of the coal heap should be < 3 metres (B) Maximum 200 tons should be stored in a heap (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Safe condition for storage of high V.M. bituminous coal is that (A) Height of the coal heap should be < 3 metres (B) Maximum 200 tons should be stored in a heap (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The main aspect of 'casual research' is ____________ 1. necessary condition 2. sufficient condition 3. both 1 & 2 4. neither 1 nor 2 5. none of these

Description : The main aspect of 'casual research' is ____________ 1. necessary condition 2. sufficient condition 3. both 1 & 2 4. neither 1 nor 2 5. none of these

Last Answer : both 1 & 2

Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Description : Hydraulic mean depth (Dm) for a circular pipe of diameter 'D' flowing full is 0.25 D. For a circular channel, at Dm = 0.3 D, gives the condition for the maximum (A) Flow rate (B) Mean velocity (C) Both 'a' & 'b' (D) Neither 'a' nor 'b

Last Answer : (B) Mean velocity

Fanning friction factor equation applies to the __________ fluid flow. (A) Non-isothermal condition of (B) Compressible (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Fanning friction factor equation applies to the __________ fluid flow. (A) Non-isothermal condition of (B) Compressible (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

If the catalyst pore size is small in comparison with the mean free path, collisions with the pore wall controls the process'. The diffusivity under this condition is called 'Knudsen diffusivity', which is affected by the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : If the catalyst pore size is small in comparison with the mean free path, collisions with the pore wall controls the process'. The diffusivity under this condition is called 'Knudsen diffusivity', which is affected by the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

Resistance to fusion of the refractory under a steady rising temperature condition is called (A) Spalling (B) Refractoriness (C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Resistance to fusion of the refractory under a steady rising temperature condition is called (A) Spalling (B) Refractoriness (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Refractoriness

When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Description : When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Last Answer : Answer: Option C

Indicate the condition in which neither trimethoprim nor sulfamethoxazole alone are effective, but their combination cotrimoxazole is: A. Prostatitis B. Lymphogranuloma venereum C. Pneumocystis carinii pneumonia D. Bacillary dysentery

Description : Indicate the condition in which neither trimethoprim nor sulfamethoxazole alone are effective, but their combination cotrimoxazole is: A. Prostatitis B. Lymphogranuloma venereum C. Pneumocystis carinii pneumonia D. Bacillary dysentery

Last Answer : C. Pneumocystis carinii pneumonia

A pushdown automation M = (Q, Σ, Γ, δ, q0, z, F) is set to be deterministic subject to which of the following condition(s), for every q ∈ Q, a ∈ Σ ∪ {λ} and b ∈ Γ (s1) δ(q, a, b) contains at most one element (s2) if δ(q, λ, b) is not empty then δ(q, c, b) must be empty for every c ∈ Σ (A) only s1 (B) only s2 (C) both s1 and s2 (D) neither s1 nor s2

Description : A pushdown automation M = (Q, Σ, Γ, δ, q0, z, F) is set to be deterministic subject to which of the following condition(s), for every q ∈ Q, a ∈ Σ ∪ {λ} and b ∈ Γ (s1) δ(q, a, b) contains at most one ... ) must be empty for every c ∈ Σ (A) only s1 (B) only s2 (C) both s1 and s2 (D) neither s1 nor s2

Last Answer : (C) both s1 and s2

Split flywheel is made to (A) Avoid cooling stresses (B) Minimize large centrifugal forces (C) Reduce weight (D) All of the above

Description : Split flywheel is made to (A) Avoid cooling stresses (B) Minimize large centrifugal forces (C) Reduce weight (D) All of the above

Last Answer : (A) Avoid cooling stresses

Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub

Description : Sunk key fits in the keyway of the .......... only. A. Sleeve B. Hub C. Both sleeve and hub D. neither sleeve and hub

Last Answer : B. Hub

Particular negative proposition distributes __________. A) Subject B) Predicate C) Both Subject and Predicate D) Neither Subject nor Predicate.

Description : Particular negative proposition distributes __________. A) Subject B) Predicate C) Both Subject and Predicate D) Neither Subject nor Predicate.

Last Answer : B) Predicate

Universal negative proposition distributes___________. A) Subject B) Predicate C) Both Subject and Predicate D) Neither Subject nor Predicate.

Description : Universal negative proposition distributes___________. A) Subject B) Predicate C) Both Subject and Predicate D) Neither Subject nor Predicate. 

Last Answer : C) Both Subject and Predicate

Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true

Last Answer : (a) Both A and R are individually true and R is the correct explanation of A

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1