Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Last Answer : b) False
Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False
Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False
Last Answer : a) True
Description : Crests and roots of the threads may lead to leakage in fluid tight threads if flattened or rounded to a circular arc. a) True b) False
Description : The following statement is an example of what kind of logical fallacy? "The university should increase funding of intramural sports because it has a responsibility to back its sports programs financially." a) ... Reasoning c) Ad Populum (Bandwagon) Argument d) False Analogy e) None of the above
Last Answer : b) Circular Reasoning
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Description : In cold riveting like hot riveting shank is subjected to majorly tensile stress. a) True b) False
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Description : Distortion energy theory is slightly liberal as compared to maximum shear stress theory. a) True b) False
Description : Maximum Principal Stress Theory is not good for brittle materials. a) True b) False
Description : The normal stress is perpendicular to the area under considerations, while the shear stress acts over the area. a) True b) False
Description : Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned
Last Answer : d) Each of the mentioned
Description : Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined
Last Answer : a) Reduce the stress concentration
Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C
Last Answer : (A) (4C - 1/4C - 4) + 0.615/C
Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69
Last Answer : b) 0.87
Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545
Last Answer : b) 1.175
Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above
Last Answer : (D) All of above
Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above
Last Answer : a. 1.558
Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )
Last Answer : b. ( K f – 1 ) / ( K t – 1 )
Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above
Last Answer : D. All of the above
Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load
Last Answer : a) Ductile material under static load
Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material
Last Answer : a) Increase
Description : If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1
Last Answer : b) 3
Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)
Last Answer : (B) (Kf - 1)/ (Kt - 1)
Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out
Last Answer : (a) stick-slip
Description : Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned
Last Answer : a) Completely
Description : Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out
Last Answer : a) Stick-slip
Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned
Last Answer : b) Fatigue
Description : Which of the following conditions is true for repeated stress? 1. σ m = 0 2. σ m = σ max / 2 3. σ m = σ a 4. σ min = 0 5. σ min = - σ max 6. σ a = σ max / 2 where σ m = mean ... amplitude a. condition 2 and 3 b. condition 1, 3 and 5 c. condition 2, 4, and 6 d. condition 3,4, 5 and 6
Last Answer : c. condition 2, 4, and 6
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : Cotter joint is going to be use to connect the two rods for torque transmission purpose. a) True b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False