Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Which of the following reduces the stress concentration?

a) Use of multiple notches

b) Drilling additional holes

c) Removal of undesired material

d) Each of the mentioned
by

1 Answer

Answer :

d) Each of the mentioned
by

Related questions

Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Description : Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Last Answer : a) Reduce the stress concentration

Welded joints require a. Punching of holes b. Drilling of holes c. Punching & Drilling of holes d. None

Description : Welded joints require a. Punching of holes b. Drilling of holes c. Punching & Drilling of holes d. None

Last Answer : d. None

The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Last Answer : (D) All of above

Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal of load c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Description : Which of the following facts are true for resilience? a) Ability of material to absorb energy when deformed elastically b) Ability to retain deformation under the application of load or after removal ... c) Ability of material to absorb energy when deformed plastically d) None of the mentioned

Last Answer : a) Ability of material to absorb energy when deformed elastically

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

Removal of undesired suckers, done once in 45 days of planting

Description : Removal of undesired suckers, done once in 45 days of planting

Last Answer : Ans. Desuckering

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

Flywheel is used in (A) Punch press (B) Drilling machine (C) Surface grinder (D) Milling machine

Description : Flywheel is used in (A) Punch press (B) Drilling machine (C) Surface grinder (D) Milling machine

Last Answer : (A) Punch press

Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Description : Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Last Answer : a) True

Keyed joints never lead to stress concentration on shafts. a) True b) False

Description : Keyed joints never lead to stress concentration on shafts. a) True b) False

Last Answer : b) False

Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Last Answer : (A) (4C - 1/4C - 4) + 0.615/C

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Description : If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Last Answer : b) 3

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Last Answer : b) False

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Last Answer : b) False

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Last Answer : a) Alternating Stresses

The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Last Answer : a) Fluctuating Stresses

The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned

Description : The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned

Last Answer : a) Hexagon

Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Description : Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Last Answer : (C) Under stressing the specimen

The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to yield and adopt its shape to that of journal is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (B) Conformability

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (A) Embeddability

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Last Answer : (c) Both (a) & (b)

What is drilling perfectly, round holes in my tree, they tend to run in a line and the bark is turning black in color

Description : What is drilling perfectly, round holes in my tree, they tend to run in a line and the bark is turning black in color

Last Answer : Bees, boring bees. They boor holes, perfectly round holes into wood.

Holes for riveting purposes should be preferably made by (A) Cutting torch (B) Drilling (C) Punching (D) None of these

Description : Holes for riveting purposes should be preferably made by (A) Cutting torch (B) Drilling (C) Punching (D) None of these

Last Answer : (B) Drilling

Rotary drilling (A) Is not suitable for deposits containing very coarse gravel (B) Hinders the ground water observations and permeability test (C) Is not economical for holes of less than 10 cm (D) All the abov

Description : Rotary drilling (A) Is not suitable for deposits containing very coarse gravel (B) Hinders the ground water observations and permeability test (C) Is not economical for holes of less than 10 cm (D) All the above

Last Answer : Answer: Option D

It is the process of placing seeds in holes made in the seedbed and closing the seed with soil. In this method, seeds are placed in holes made at definite depth at fixed spacing. b. Drilling c. Broadcasting d. None of the above

Description : It is the process of placing seeds in holes made in the seedbed and closing the seed with soil. In this method, seeds are placed in holes made at definite depth at fixed spacing. b. Drilling c. Broadcasting d. None of the above.

Last Answer : Ans - a. Dibbing

is the process of placing seeds in holes made in seedbed and covering them. a) Broadcasting. b) Dibbling c) Drilling. d) Transplanting

Description : is the process of placing seeds in holes made in seedbed and covering them. a) Broadcasting. b) Dibbling c) Drilling. d) Transplanting

Last Answer : Dibbling

Coherence of laser light is important for _________ ∙ a. Light propagation ∙ b. Getting laser light to pass through air ∙ c. Drilling holes ∙ d. Holography

Description : Coherence of laser light is important for _________ ∙ a. Light propagation ∙ b. Getting laser light to pass through air ∙ c. Drilling holes ∙ d. Holography

Last Answer : d. Holography

The mechanism involved in the removal of metal in drilling operation is by (A) Compression (B) Extrusion (C) Shearing (D) Both 'b' & 'c'

Description : The mechanism involved in the removal of metal in drilling operation is by (A) Compression (B) Extrusion (C) Shearing (D) Both 'b' & 'c'

Last Answer : (D) Both 'b' & 'c'

Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress

Last Answer : b. stress concentration

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Description : If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Last Answer : a) Solid length

Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Description : Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Last Answer : d) Each of the mentioned

Sketch the method to reduced stress concentration in cylindrical members with holes.

Description : Sketch the method to reduced stress concentration in cylindrical members with holes.

Last Answer : The methods of reducing stress concentration in cylindrical members with shoulders hole, subjected to tensile load. 

What is the bone with two sciatic notches?

Description : What is the bone with two sciatic notches?

Last Answer : Need answer

A depth-discharge relationship of the canal section is maintained at a notch fall because the sill of the notches is : a) Level with downstream canal bed b) Below the upstream canal bed c) Level with upstream canal bed d) Above the upstream canal bed

Description : A depth-discharge relationship of the canal section is maintained at a notch fall because the sill of the notches is : a) Level with downstream canal bed b) Below the upstream canal bed c) Level with upstream canal bed d) Above the upstream canal bed

Last Answer : c) Level with upstream canal bed

The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping (C) Most concentrated liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Description : The advantage of backward feed multiple effect evaporators over forward feed units is that (A) Heat sensitive material can be handled (B) There is no additional cost of pumping ... liquid is at highest temperature (D) Equal heat transfer co-efficients exist in various effects

Last Answer : (C) Most concentrated liquid is at highest temperature

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

The knuckle joint is used to connect the... A. Two roads whose Axes are coincide or intersecting and lies in single plane. B. Two roads whose Axes are coincide or intersecting and lies in multiple plane. C. Two roads whose Axes are parallel or intersecting and lies in single plane. D. None of the above

Description : The knuckle joint is used to connect the... A. Two roads whose Axes are coincide or intersecting and lies in single plane. B. Two roads whose Axes are coincide or intersecting and lies in multiple ... Two roads whose Axes are parallel or intersecting and lies in single plane. D. None of the above

Last Answer : A. Two roads whose Axes are coincide or intersecting and lies in single plane.

Have you ever followed advice that resulted in an undesired outcome?

Description : Have you ever followed advice that resulted in an undesired outcome?

Last Answer : I give unsolicited advice all the attention due.

Phenomena in which signal transmitted in one circuit creates undesired effect in other circuit is known as A. crosstalk B. signal attenuation C. sampling D. crosslinking

Description : Phenomena in which signal transmitted in one circuit creates undesired effect in other circuit is known as A. crosstalk B. signal attenuation C. sampling D. crosslinking

Last Answer : crosslinking