Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Use of multiple notches in a V shaped flat plate will

a) Reduce the stress concentration

b) Increase the stress concentration

c) No effect

d) Cannot be determined
by

1 Answer

Answer :

a) Reduce the stress concentration
by

Related questions

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Description : Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Last Answer : d) Each of the mentioned

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Description : If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Last Answer : b) 3

Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Last Answer : a) decreases

When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Last Answer : b) Split flywheel

Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Description : Split flywheel is made to 1. avoid cooling stress 2. reduce weight 3. increase weight 4. maximize large centrifugal force

Last Answer : 1. avoid cooling stress

Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above

Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above

Last Answer : c. Principal stress

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Last Answer : b) False

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Description : If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Last Answer : a) Hydrostatic

If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Last Answer : a) They are high

Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Description : Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Last Answer : b) Electric arc welding

Which threads have greater resistance to unscrewing? a) Coarse b) Fine c) They have equal resistance d) Cannot be determined

Description : Which threads have greater resistance to unscrewing? a) Coarse b) Fine c) They have equal resistance d) Cannot be determined

Last Answer : b) Fine

Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Last Answer : iii. 5/8”

Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Last Answer : iii. 3/8”

Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Description : Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Last Answer : a) True

Keyed joints never lead to stress concentration on shafts. a) True b) False

Description : Keyed joints never lead to stress concentration on shafts. a) True b) False

Last Answer : b) False

Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Last Answer : (A) (4C - 1/4C - 4) + 0.615/C

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Last Answer : (D) All of above

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Last Answer : b) False

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

The tensile stress in the rim of the flywheel is given by, Where, ρ is mass density and v is linear velocity at the mean radius of the rim. (A) ρv2/2 (B) πρv2 (C) ρv2 (D) 2 ρv2

Description : The tensile stress in the rim of the flywheel is given by, Where, ρ is mass density and v is linear velocity at the mean radius of the rim. (A) ρv2/2 (B) πρv2 (C) ρv2 (D) 2 ρv2

Last Answer : (C) ρv2

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Description : Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Last Answer : a) True

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Which of the following areas CANNOT be determined by survey analysis of partially edentulous cast? A. Areas to be revealed as blocked out to properly located rigid parts of a frame work B. Areas to be shaped to properly located rigid parts of framework C. Areas used for guideline planes D. Areas used for retention E. Areas used for support F. Depth of rest seats

Description : Which of the following areas CANNOT be determined by survey analysis of partially edentulous cast? A. Areas to be revealed as blocked out to properly located rigid parts of a frame work B. Areas to be ... planes D. Areas used for retention E. Areas used for support F. Depth of rest seats

Last Answer : F. Depth of rest seats

Which one of the following is correct? [IES-2008] A hydrodynamic slider bearing develops load bearing capacity mainly because of- (a) Slider velocity (b) wedge shaped oil film (c) Oil compressibility (d) oil viscosity

Description : Which one of the following is correct? [IES-2008] A hydrodynamic slider bearing develops load bearing capacity mainly because of- (a) Slider velocity (b) wedge shaped oil film (c) Oil compressibility (d) oil viscosity

Last Answer : (b) wedge shaped oil film

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Visualization in the instructional process cannot increase (a) Interest and motivation (b) Retention and adaptation (c) Stress and boredom (d) Curiosity and concentration

Description : Visualization in the instructional process cannot increase (a) Interest and motivation (b) Retention and adaptation (c) Stress and boredom (d) Curiosity and concentration

Last Answer : (c) Stress and boredom

When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Last Answer : 1. Accelerated

When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Last Answer : a) Accelerated

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Last Answer : b) Double force

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Description : A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Last Answer : (B) 20 KPa

If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted with complete dewatering continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Description : If water table is encountered in the standard pit while conducting plate load test (a) The load test should be abandoned (b) The pit is considered unsafe (c) Test should be conducted ... continuously throughout the test duration (d) The bearing capacity of soil cannot be determined in this condition

Last Answer : (c) Test should be conducted with complete dewatering continuously throughout the test duration

In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Last Answer : (c) Converging film

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution