The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____

failure.

a) Fracture

b) Fatigue

c) Yielding

d) None of the mentioned
by

1 Answer

Answer :

b) Fatigue
by

Related questions

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Last Answer : (a) stick-slip

Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Description : Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Last Answer : a) Stick-slip

The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Last Answer : a) Fluctuating Stresses

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses

Description : If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses

Last Answer : d) Reversed Stresses

The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses

Last Answer : d) Reversed Stresses

The stress represented by sin (t) + 1 belongs to which category? a) Fluctuating Stresses b) Alternating stresses c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by sin (t) + 1 belongs to which category? a) Fluctuating Stresses b) Alternating stresses c) Repeated Stresses d) Reversed Stresses

Last Answer : c) Repeated Stresses

Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does not occur (C) Initiation of crack occurs on the surface of the machine part (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Description : Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does ... (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Last Answer : Option B

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Last Answer : (C) Fluctuating

Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating(B) Tensile(C) Compressive(D) Torsion

Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion

Last Answer : (A) Fluctuating

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Last Answer : b) False

Fatigue failure is time dependent failure. a) True b) False

Description : Fatigue failure is time dependent failure. a) True b) False

Last Answer : a) True

Why do we determine principal stresses? a. Failure is due to simple stress or strain b. Failure is due to complex stress or strain c. Both (a) & (b) d. None

Description : Why do we determine principal stresses? a. Failure is due to simple stress or strain b. Failure is due to complex stress or strain c. Both (a) & (b) d. None

Last Answer : a. Failure is due to simple stress or strain

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

The phenomenon of slow extension of materials having constant load, i.e. increasing with the time is called (A) Creeping (B) Yielding (C) Breaking (D) None of these

Description : The phenomenon of slow extension of materials having constant load, i.e. increasing with the time  is called  (A) Creeping  (B) Yielding  (C) Breaking  (D) None of these 

Last Answer : (A) Creeping 

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Description : The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses

Last Answer : a) Alternating Stresses

The total strain energy for a unit cube subjected to three principal stresses is given by? a) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/3 b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ c) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/4 d) None of the mentioned

Description : The total strain energy for a unit cube subjected to three principal stresses is given by? a) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/3 b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ c) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/4 d) None of the mentioned

Last Answer : b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Last Answer : (b) Due to tensile

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed

Description : Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed

Last Answer : a) Fine threads

The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Description : The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Last Answer : (c) fluctuating stress

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned

Description : Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned

Last Answer : a) Completely

If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2

Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2

Last Answer : a) 72 N/mm2

Theories of elastic failure while dealing with brittle materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Description : Theories of elastic failure while dealing with brittle materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Last Answer : (a) Ultimate stress

Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Description : Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Last Answer : (b) Yield stress

Theories of elastic failure help to recognize (a) Weak materials (b) Strong materials (c) Both weak and strong materials (d) None

Description : Theories of elastic failure help to recognize (a) Weak materials (b) Strong materials (c) Both weak and strong materials (d) None

Last Answer : (c) Both weak and strong materials

When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing stress is more than crushing stress induced in the threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Last Answer : Option C

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Last Answer : a) Elastically

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Description : The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Last Answer : (a) higher

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Last Answer : b) 2

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

Split flywheel is made to (A) Avoid cooling stresses (B) Minimize large centrifugal forces (C) Reduce weight (D) All of the above

Description : Split flywheel is made to (A) Avoid cooling stresses (B) Minimize large centrifugal forces (C) Reduce weight (D) All of the above

Last Answer : (A) Avoid cooling stresses