Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out
Last Answer : (a) stick-slip
Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned
Last Answer : b) Fatigue
Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion
Last Answer : (b) Pitting
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture
Last Answer : c) Creep
Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed
Last Answer : a) Elastically
Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue
Last Answer : (b) corrosive
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65
Last Answer : (c) 0.50
Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point
Last Answer : (c) endurance limit to the working stress
Description : The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same
Last Answer : (a) higher
Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit
Last Answer : (d) endurance limit
Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point
Last Answer : (d) below the yield point
Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load
Last Answer : (d) completely reversed load
Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No
Last Answer : a) Yes
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : b) 2
Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above
Last Answer : a. 1.558
Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above
Last Answer : a. Ferrous materials
Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )
Last Answer : b. ( K f – 1 ) / ( K t – 1 )
Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False
Last Answer : b) False
Description : Fatigue failure is time dependent failure. a) True b) False
Last Answer : a) True
Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue
Last Answer : d) Fatigue
Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)
Last Answer : (B) (Kf - 1)/ (Kt - 1)
Description : Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does ... (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface
Last Answer : Option B
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping
Last Answer : (a) Fatigue Failure
Description : The permanent mode of deformation of a material known as _____________ a) Elasticity b) Plasticity c) Slip deformation d) Twinning deformation
Last Answer : b) Plasticity
Description : Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned
Last Answer : a) Completely
Description : Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False
Description : Strain hardening effect in metals subjected to cold working is due to the __________ mechanism. (A) Slip (B) Fracture (C) Winning (D) Dislocation
Last Answer : (D) Dislocation
Description : Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism. (A) Fracture (B) Dislocation (C) Slip (D) Twinning
Last Answer : (C) Slip
Description : What percentage of patients who survived the polio epidemic of the 1950s are now estimated to have developed post-polio syndrome? a) 60-80% Patients who survived the polio epidemic of the 1950s ... 80% of patients who survived the polio epidemic of the 1950s are now experiencing post-polio syndrome.
Last Answer : a) 60-80% Patients who survived the polio epidemic of the 1950s, many now elderly, are developing new symptoms of weakness, fatigue and musculoskeletal pain. It is estimated that between 60% and 80% of the 640,000 polio survivors are experiencing the phenomenon known as post-polio syndrome.
Description : What phenomenon will result if the glass fiber is exposed to long periods of high humidity? ∙ A. stress fatigue ∙ B. core corrosion ∙ C. stress corrosion ∙ D. cladding corrosion
Last Answer : stress corrosion
Description : The coating in a fiber helps protect fiber from moisture, which reduces the possibility of the occurrence of a detrimental phenomenon called ∙ A. static fatigue ∙ B. mechanical fatigue ∙ C. stress fatigue ∙ D. coating fatigue
Last Answer : ∙ A. static fatigue
Description : The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect
Last Answer : b) Equal to
Description : The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends. a) Minimum, maximum b) Maximum, minimum c) Minimum, minimum d) Zero, infinity
Last Answer : b) Maximum, minimum
Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above
Last Answer : b. intensity of direct stress
Description : The maximum tangential stress σ t = (σ x sin 2θ)/2 is maximum if, θ is equal to ________ a. 45 o b. 90 o c. 270 o d. all of the above
Last Answer : a. 45 o
Description : Principal stress is the magnitude of ________ stress acting on the principal plane. a. Normal stress b. Shear stress c. Both a. and b. d. None of the above
Last Answer : a. Normal stress
Description : Which of the following phenomenon/ phenomena is/are diffusion controlled? (A) Dislocation climb (B) Cross-slip (C) Twinning (D) Recrystallisation
Last Answer : (D) Recrystallisation
Description : ________ cannot increase the fatigue strength of a material. (A) Grain refining (B) Grain coarsening (C) Surface hardening (D) Shot peening
Last Answer : (B) Grain coarsening
Description : The most important task in teaching is Options: A) Making assignments and hearing recitations B) Directing pupils in development of experiences C) Scoring test papers and giving out-grades D) Making monthly reports and keeping records
Last Answer : B) Directing pupils in development of experiences
Description : The synchronous speed of an induction motor is the ________. A. speed at which the rotor turns B. speed of the rotating field C. frequency of the rotor current D. slip in per cent of rotor RPM
Last Answer : Answer: B
Description : Can a player in any sport be sued by a fan, or punished, for scoring on their own net, or throwing the game ?
Last Answer : No. Never. We are living in the age of cancel culture and it’s already terrifying enough. And it’s not the player’s fault that someone loses money. You put the bet, you know the risk. No one forces you to. Anything else is just needless violence.
Description : What are the most favourite sports scoring apps for Android and iOS in China?
Last Answer : So you want an app localized for the Chineese language that reports live scores of US sports games, and you don’t speak Chineese? That doesn’t make any sense.
Description : Love, 15, 30, 40,... What's up with the scoring system in tennis?
Last Answer : I heard that the “love” score is a bastardization of the french word “l’oeuf” (egg) and the scores used to go love, 15, 30, 45, (60) but got abbreviated later on.
Description : What is a good site for learning the rules and scoring of tennis?
Last Answer : @gailcalled – Your answer is not helpful. Please read my extended description.
Description : Do you think the current credit scoring system is fair?
Last Answer : Honestly, I’m not sure what changes have taken place in order to judge. Once I moved into my house, I kind of forgot all about credit since I don’t use it.