Description : Process of welding with respect to riveting takes a. More time b. Less time c. Same time d. None
Last Answer : b. Less time
Description : Cold riveting holds the connected parts better than hot riveting. a) True b) False
Last Answer : b) False
Description : In cold riveting like hot riveting shank is subjected to majorly tensile stress. a) True b) False
Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None
Last Answer : iii. 5/8”
Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None
Last Answer : iii. 3/8”
Description : Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting
Last Answer : (D) Welding takes more time than riveting
Description : Out of the following, the joint produced by __________ has the lowest strength. (A) Soldering (B) Welding (C) Brazing (D) Riveting
Last Answer : (A) Soldering
Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded
Last Answer : (D) Mild steel sheet cannot be spot welded
Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length
Last Answer : (A) Electrode size
Description : If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is given by (A) (b + d)/b (B) (b - d)/b (C) (d - b)/d (D) (b - d)/d
Last Answer : (B) (b - d)/b
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Last Answer : a) True
Description : In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty
Last Answer : b) Increase with increase in speed
Description : Heating and cooling in welding is a. Even b. Non-even c. Cannot say d. None
Last Answer : b. Non-even
Description : Welding requires a. Non-skilled worker b. Skilled worker c. Any worker
Last Answer : b. Skilled worker
Description : Projection welding is (i) Electric arc welding (ii) Gas welding (iii)Spot welding (iv) None
Last Answer : (iv) None
Description : Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding
Last Answer : (iv)Starting and stopping allowance for welding
Description : Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None
Last Answer : (iii) Temperature of welding
Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding
Last Answer : (iv) Machine used in welding
Description : In which case, molten metal is used to do welding? (i) Groove type (ii) spot type (iii) Plug type (iv) None
Last Answer : (iii) Plug type
Description : Which type of welding is generally used in automobile sector? a) Electric arc welding b) Electric resistance welding c) Gas welding d) Forge welding
Last Answer : b) Electric resistance welding
Description : Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed
Last Answer : b) No filler material used
Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed
Last Answer : b) No, it is done up to plastic stage
Description : Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined
Last Answer : b) Electric arc welding
Description : In gas welding which of the following is generally used? a) Oxygen-Hydrogen b) Oxygen-Acetylene c) Oxygen-Hydrogen or Oxygen-Acetylene d) None of the mentioned
Last Answer : c) Oxygen-Hydrogen or Oxygen-Acetylene
Description : Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding
Last Answer : a) Thermit welding
Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed
Last Answer : b) No, fusion doesn’t require
Description : The electric arc welding is a type of ............. welding. (a) forge (b) fusion
Last Answer : b) fusion
Description : In a fusion welding process, (a) only heat is used (b) only pressure is used (c) combination of heat and pressure is used (d) none of these
Last Answer : (a) only heat is used
Description : Maximum carbon content in welding is usually limited to a) 0.22% b) 0.8% c) 1.5% d) 2%
Last Answer : a) 0.22%
Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160
Last Answer : 2. 790
Description : A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008 ... Gets reduced to one-fourth of original value (d) Gets reduced to half of original value
Last Answer : (a) Remains unchanged
Description : The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above
Last Answer : (B) curvature
Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed
Last Answer : b) 360/t
Description : Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t
Last Answer : c) 250000 t
Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter
Last Answer : (B) Inner diameter
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : The key in the form of semi-circular disk of uniform thickness is called, (A) Sunk key (B) Feather key (C) Woodruff key (D) Kennedy key
Last Answer : (C) Woodruff key
Description : Saddle key is more suitable than sunk key for heavy duty applications. a) True b) False
Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False
Description : The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight. a) True b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Last Answer : (b) False
Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False
Description : For majority of bearings, actual life is considerably greater than rated life. a) True b) False
Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False
Description : Compressed length is smaller than the solid length. a) True b) False
Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False