Description : The equivalent length of a column fixed at both ends, is (A) 0.5 l (B) 0.7 l (C) l (D) 1.5 l
Last Answer : (A) 0.5 l
Description : A column of length (l) with both ends fixed may be considered as equivalent to a column of length __________ with both ends hinged. (a) l/8 (b) l/4 (c) l/2 (d) l
Last Answer : c) l/2
Description : The equivalent length of a column fixed at both ends, is (a) 0.5 l (b) 0.7 l (c) l (d) 1.5 l
Last Answer : (a) 0.5 l
Description : A shaft of length l carries two discs at its two ends. The lowest torsional frequency is ω n . If the shaft length is doubled, then the lowest torsional frequency becomes A ω n /2 B ω n /√2 C √2ω n D 2ω n
Last Answer : B ω n /√2
Description : A column has its equivalent length equal to its length in case of a.one end fixed, other free b.both ends hinged c.one end hinged, other free d.107 dynes e.both end fixed
Last Answer : b. both ends hinged
Description : A column with maximum equivalent length has (a) both ends hinged (b) both ends fixed (c) one end fixed and the other end hinged (d) one end fixed and the other end free
Last Answer : (d) one end fixed and the other end free
Description : A column of length 4m with both ends fixed may be considered as equivalent to a column of length ………….with both ends hinged. (a) 2 m (b) 1 m (c) 3 m (d) 6 m
Last Answer : For a long column subjected to 1 point axial compressive load, its buckling strength will be maximum when its
Description : According to Euler’s column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends. (a) equal to (b) two times (c) four times (d) eight times
Last Answer : (c) four times
Description : The equivalent length of a column fixed at one end and free at the other end, is (A) 0.5 l (B) 0.7 l (C) 2 l (D) 1.5 l
Last Answer : (C) 2 l
Description : Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (A) One end is fixed and other end is hinged (B) Both ... (C) One end is fixed and the other end entirely free (D) Both the ends are fixed
Last Answer : (D) Both the ends are fixed
Description : Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (a) One end is fixed and other end is hinged (b) ... (c) One end is fixed and the other end entirely free (d) Both the ends are fixed
Last Answer : (d) Both the ends are fixed
Description : Euler's formula states that the buckling load for a column of length , both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are and respectively, is given by the relation (A) P = ²EI/l² (B) P = /EI (C) P = /l² (D) P = ²EI/l
Last Answer : (A) P = ²EI/l²
Description : The effective length of a R.C column continuing through two storeys, properly restrained at both ends in position and direction, is (a) 0.50 L (b) 0.75 L (c) L (d) 2 L
Last Answer : (b) 0.75 L
Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface
Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut
Description : The ratio of crippling loads of a column having both the ends fixed to the column having both the ends hinged, is (A) 1 (B) 2 (C) 3 (D) 4
Last Answer : (D) 4
Description : While designing the pile as a column, the end conditions are nearly (A) Both ends hinged (B) Both ends fixed (C) One end fixed and other end hinged (D) One end fixed and other end free
Last Answer : Answer: Option C
Description : A long column with fixed ends can carry load as compared to both ends hinged (a) 4 times (b) 8 times (c) 16 times (d) None
Last Answer : (a) 4 times
Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed
Last Answer : a) 0.707 hl
Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed
Last Answer : b) 1.21P/hl
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : A long column with fixed ends can carry load as compared to cantilever column (a) 4 times (b) 8 times (c) 16 times (d) None
Last Answer : (c) 16 times
Description : Sphericity of a cubical particle, when its equivalent diameter is taken as the height of the cube, is (A) 0.5 (B) 1 (C) √2 (D) √3
Last Answer : (B) 1
Description : The ends of spring, which are in contact with the seat, are (A) Active coils (B) Inactive coils (C) Transmit maximum force (D) Do not transmit any force
Last Answer : (B) Inactive coils
Description : Spring having square ends has 1 inactive coil. a) True b) False
Last Answer : b) False
Description : The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends. a) Minimum, maximum b) Maximum, minimum c) Minimum, minimum d) Zero, infinity
Last Answer : b) Maximum, minimum
Description : An instrument has two strings. Both have the same length and are uniform. One of the strings is under twice as much tension as the other and also twice the mass of the other. Then which of ... d) Both strings vibrate with the same frequency and have the same wave-length and the same wave velocity.
Last Answer : Ans:(d)
Description : A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is (A) M (B) M/2 (C) M/3 (D) ML/2
Last Answer : (A) M
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False
Description : Rankine Gordon formula for buckling is valid for (A) Long column (B) Short column (C) Short and long column (D) Very long column
Last Answer : (C) Short and long column
Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0
Last Answer : (B) 12.88
Description : A circle has radius √2 cm. It is divided into two segments by a chord of length 2cm.Prove that the angle subtended by the chord at a point in major segment is 45 degree . -Maths 9th
Last Answer : Given radius =2 cm Therefore AO=2 cm Let OD be the perpendicular from O on AB And AB =2cm Therefore AD=1cm (perpendicular from the centre bisects the chord) Now in triangle AOD, AO=2 cm ... by a chord at the centre is double of the angle made by the chord at any poin on the circumference)
Description : If the length of a pendulum is doubled, its frequency of oscillation is changed by a factor of (a) 2 (b) √2 (c) 1/2 (d) 1/4
Last Answer : Ans:(c)
Description : The Effective length of a column is defined as the [ A ] length between the fixed joints [ B ] length between the points of contra flexure [ C ] unsupported length of the column [ D ] Both (a) and (c)
Last Answer : [ B ] length between the points of contra flexure
Description : The angle of twist for the equivalent bar to a spring is given by? (Symbols have their usual meaning) a) 8PD2N/Gd4 b) 16PD2N/Gd4 c) 16PDN/Gdɜ d) 8PDN/Gdɜ
Last Answer : b) 16PD2N/Gd4
Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)
Last Answer : (D) Mb +√(Mb2 + Mt2)
Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)
Last Answer : (B) √(Mb2 + Mt2)
Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse
Last Answer : b) Square
Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim
Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load
Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim
Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart
Last Answer : (d) to maintain the balls at a fixed distance apart
Description : The elastic stress strain behavior of rubber is A. Linear B. Nonlinear C. Plastic D. No fixed relationship
Last Answer : B. Nonlinear
Description : In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same
Last Answer : (A) shorten the spring
Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding
Last Answer : (iv) Machine used in welding
Description : The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied
Last Answer : (D) All of above conditions are satisfied
Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd
Last Answer : (B) 3WL/2fd²