Define Voltage to Frequency conversion factor.

Define Voltage to Frequency conversion factor. 
by

1 Answer

Answer :

Voltage to Frequency conversion factor is defined as,

 Kv = fo / Vc= 8fo /Vcc

 Vc is the modulation voltage

 fo frequency shift
by

Related questions

Define conversion time.

Description : Define conversion time.

Last Answer : conversion time of a successive approximation type ADC is given by  T(n+1)  where T---clock period  Tc---conversion time  n----no. of bits

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

How frequency to voltage converted on OP-AMPS.

Description : How frequency to voltage converted on OP-AMPS.

Last Answer : A Frequency to voltage converter produces an output voltage, whose amplitude is a function of frequency of the input signal. The input signal may be a sinewave, a square wave or a pulse train. The F/V converter is essentially an FM detector or discriminator.

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Last Answer : B. Noise improvement factor

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Description : In cellular system, _____ defines the geographic distance that is required between cells using identical frequencies in order to avoid interference between the radio transmissions at these cells. A. frequency-reuse ratio B. distance-to-reuse ratio (D/R) C. reuse format plan ratio D. reuse factor

Last Answer : B. distance-to-reuse ratio (D/R)

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

Define input offset voltage?

Description : Define input offset voltage?

Last Answer : It is defined as the voltage that must be applied between the input terminals of an op-amp to nullify the output.

Define input offset voltage.

Description : Define input offset voltage.

Last Answer : A small voltage applied to the input terminals to make the output voltage as zero when the two input terminals are grounded is called input offset voltage. 

Define current amplification factor?

Description : Define current amplification factor?

Last Answer : It is defined as the ratio of change in output current to the change in input current at constant other side voltage.

The receive GCE system in an earth station performs what function(s)? A. Modulation and multiplexing B. Up conversion C. Demodulation and demultiplexing D. Down conversion

Description : The receive GCE system in an earth station performs what function(s)? A. Modulation and multiplexing B. Up conversion C. Demodulation and demultiplexing D. Down conversion

Last Answer : C. Demodulation and demultiplexing

In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Description : In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Last Answer : B. In the nonlinear region

The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Description : The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem

Last Answer : D. Modem

What is the term for the ration of the radiation resistance of an antenna to the total resistance of the system? A. Effective radiated power B. Beamwidth C. Radiation conversion loss D. Antenna efficiency

Description : What is the term for the ration of the radiation resistance of an antenna to the total resistance of the system? A. Effective radiated power B. Beamwidth C. Radiation conversion loss D. Antenna efficiency

Last Answer : D. Antenna efficiency

A device that connects two dissimilar networks and performs the protocol conversion. A. Gateway B. Coupler C. Transformer D. Converter

Description : A device that connects two dissimilar networks and performs the protocol conversion. A. Gateway B. Coupler C. Transformer D. Converter

Last Answer : A. Gateway

A system that performs parallel-to-serial and serial-to-parallel conversion of data link. A. DCE B. DTE C. Modem D. PC

Description : A system that performs parallel-to-serial and serial-to-parallel conversion of data link. A. DCE B. DTE C. Modem D. PC

Last Answer : B. DTE

The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Description : The laser frequency when the light has the wavelength 800 nm is a. 375 x 10^12 Hz b. 475 x 10^15 Hz c. 375 x 10^9 Hz d. 375 x 10^18 Hz

Last Answer : a. 375 x 10^12 Hz

What is the photon energy for an infrared wave with frequency of 1012 Hz? a. 10.6 x 1034 joules b. 6.63 x 10-34 joules c. 6.63 x 10-22 joules d. 10.6 x 1022 joules

Description : What is the photon energy for an infrared wave with frequency of 1012 Hz? a. 10.6 x 1034 joules b. 6.63 x 10-34 joules c. 6.63 x 10-22 joules d. 10.6 x 1022 joules

Last Answer : c. 6.63 x 10-22 joules

When a beam of light enters one medium from another, which quantity will not change? a. Direction b. Speed c. Frequency d. Wavelength

Description : When a beam of light enters one medium from another, which quantity will not change? a. Direction b. Speed c. Frequency d. Wavelength

Last Answer : c. Frequency

What generates a light beam of a specific visible frequency? a. Laser b. Maser c. Infrared d. Flashlight

Description : What generates a light beam of a specific visible frequency? a. Laser b. Maser c. Infrared d. Flashlight

Last Answer : a. Laser

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Last Answer : B. 6546 kHz

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Description : Which of the following antennas is used for testing and adjusting a transmitter for proper modulation, amplifier operation and frequency accuracy? A. Elementary B. Real C. Isotropic D. Dummy

Last Answer : D. Dummy

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

What determines antenna polarization? A. The frequency of the radiated wave B. The direction of the radiated wave C. The direction of the magnetic field vector D. The direction of the electric field vector

Description : What determines antenna polarization? A. The frequency of the radiated wave B. The direction of the radiated wave C. The direction of the magnetic field vector D. The direction of the electric field vector

Last Answer : D. The direction of the electric field vector

The best solution to fading is _____. A. space diversity B. frequency diversity C. polarization diversity D. wavelength diversity

Description : The best solution to fading is _____. A. space diversity B. frequency diversity C. polarization diversity D. wavelength diversity

Last Answer : A. space diversity

A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Description : A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Last Answer : A. Antenna

When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Description : When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Last Answer : A. 196 dB

The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Description : The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Last Answer : A. 403 dB

How can multiple earth stations share a satellite on the same frequencies? A. Frequency reuse B. Multiplexing C. Mixing D. Frequency hopping

Description : How can multiple earth stations share a satellite on the same frequencies? A. Frequency reuse B. Multiplexing C. Mixing D. Frequency hopping

Last Answer : A. Frequency reuse

Most satellites operate in which frequency band? A. 30 to 300 MHz B. 300 MHz to 3 GHz C. 3 GHz to 30 GHz D. Above 300 GHz

Description : Most satellites operate in which frequency band? A. 30 to 300 MHz B. 300 MHz to 3 GHz C. 3 GHz to 30 GHz D. Above 300 GHz

Last Answer : C. 3 GHz to 30 GHz

A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Description : A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Last Answer : D. FDMA

The bandwidth of C-band satellite frequency band in U.S. A. 500 GHz B. 1000 GHz C. 1000 MHz D. 500 MHz

Description : The bandwidth of C-band satellite frequency band in U.S. A. 500 GHz B. 1000 GHz C. 1000 MHz D. 500 MHz

Last Answer : D. 500 MHz

The frequency of Ku band for satellite communications. A. 6/4 GHz B. 14/11 GHz C. 12/14 GHz D. 4/8 GHz

Description : The frequency of Ku band for satellite communications. A. 6/4 GHz B. 14/11 GHz C. 12/14 GHz D. 4/8 GHz

Last Answer : B. 14/11 GHz

What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Description : What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Last Answer : C. 2225 MHz

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

What is the frequency range of C-band? A. 8.5 to 12.5 GHz B. 3.4 to 6.425 GHz C. 12.95 to 14.95 GHz D. 27.5 to 31 GHz

Description : What is the frequency range of C-band? A. 8.5 to 12.5 GHz B. 3.4 to 6.425 GHz C. 12.95 to 14.95 GHz D. 27.5 to 31 GHz

Last Answer : B. 3.4 to 6.425 GHz

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz