Bulk of the convective heat transfer resistance from a hot tube surfaceto the fluid flowing in it, is(A) In the central core of the fluid(B) Uniformly distributed throughout the fluid(C) Mainly confined to a thin film of fluid near the surface(D) None of these

Bulk of the convective heat transfer resistance from a hot tube surfaceto the fluid flowing in it, is

(A) In the central core of the fluid

(B) Uniformly distributed throughout the fluid

(C) Mainly confined to a thin film of fluid near the surface

(D) None of these


by

1 Answer

Answer :

(C) Mainly confined to a thin film of fluid near the surface


by

Related questions

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Heat transfer by conduction in the turbulent core of a fluid flowing through a heated pipe is negligible, if the value of Prandtl number is (A) 0.2 (B) 0.4 (C) 0.6 (D) 0.8

Description : Heat transfer by conduction in the turbulent core of a fluid flowing through a heated pipe is negligible, if the value of Prandtl number is (A) 0.2 (B) 0.4 (C) 0.6 (D) 0.8

Last Answer : (C) 0.6

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Description : A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

Last Answer : (B) 0.025

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

In areas where light rains are uniformly distributed throughout the year, the type of sewerage system to be adopted is A. Separate system B. Combined system C. Partially combined system D. None of these

Description : In areas where light rains are uniformly distributed throughout the year, the type of sewerage system to be adopted is A. Separate system B. Combined system C. Partially combined system D. None of these

Last Answer : ANS: B

If a three hinged parabolic arch, (span l, rise h) is carrying a uniformly distributed load w/unit length over the entire span, (A) Horizontal thrust is wl2 /8h (B) S.F. will be zero throughout (C) B.M. will be zero throughout (D) All the above

Description : If a three hinged parabolic arch, (span l, rise h) is carrying a uniformly distributed load w/unit  length over the entire span,  (A) Horizontal thrust is wl2 /8h (B) S.F. will be zero throughout  (C) B.M. will be zero throughout  (D) All the above 

Last Answer : (D) All the above 

A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its outside edge is: w) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Description : A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its ... ) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Last Answer : ANSWER: Z -- CIRCLES THE AXIS OF THE ROD

Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Description : Heat transfer efficiency leading of energy conservation in a heat exchanger can be achieved by (A) Keeping the heat transfer surface clean (B) Enhancing the fluid pumping rate (C) Increasing the tube length (D) None of these

Last Answer : (A) Keeping the heat transfer surface clean

A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Description : A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Last Answer : (3) Near the neck Explanation: When the bottle of soda water is grasped by the neck and swung briskly in a vertical circle, the bubbles collect at the top of the bottle which is ... beverage forms form bubbles when the dissolved carbon dioxide is depressurized to form emulsions at the top.

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Description : A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Last Answer : Near the neck

For a fluid flowing in an annulus space, the wetted perimeter for heat transfer and pressure drop are (A) Same (B) Different (C) Never different (D) Linearly related

Description : For a fluid flowing in an annulus space, the wetted perimeter for heat transfer and pressure drop are (A) Same (B) Different (C) Never different (D) Linearly related

Last Answer : (B) Different

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Description : The characteristic dimensionless groups for heat transfer to a fluid flowing through a pipe in laminar flow are (A) Re.Gz (B) Nu, Pr (C) Nu, Pr, Re (D) Nu, Gz

Last Answer : (D) Nu, Gz

Convective heat transfer, in which heat is transferred by movement of warmed matter is described by (A) Fourier's law (B) Newton's law of cooling (C) Fick's law (D) None of these

Description : Convective heat transfer, in which heat is transferred by movement of warmed matter is described by (A) Fourier's law (B) Newton's law of cooling (C) Fick's law (D) None of these

Last Answer : (B) Newton's law of cooling

The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Description : The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half left hand span. The horizontal thrust at the support will be (A) 10.8 tonnes (B) 1.08 tonnes (C) 1.8 tonnes (D) 0.8 tonnes

Description : A three hinged parabolic arch hinged at the crown and springing, has a horizontal span of 4.8 m  and a central rise of 1 m. It carries a uniformly distributed load of 0.75 tonne per metre over half  left hand span ... A) 10.8 tonnes  (B) 1.08 tonnes  (C) 1.8 tonnes  (D) 0.8 tonnes 

Last Answer : (B) 1.08 tonnes 

The ratio of the maximum deflections of a beam simply supported at its ends with an isolated central load and that of with a uniformly distributed load over its entire length, is (A) 3/2 (B) 15/24 (C) 24/15 (D) 2/3

Description : The ratio of the maximum deflections of a beam simply supported at its ends with an isolated central load and that of with a uniformly distributed load over its entire length, is (A) 3/2 (B) 15/24 (C) 24/15 (D) 2/3

Last Answer : (C) 24/15

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

At Pr > 1, conduction in an ordinary fluid flowing through a heated pipe is limited to the (A) Buffer zone (B) Turbulent core (C) Both (A) and (B) (D) Viscous sub-layer

Description : At Pr > 1, conduction in an ordinary fluid flowing through a heated pipe is limited to the (A) Buffer zone (B) Turbulent core (C) Both (A) and (B) (D) Viscous sub-layer

Last Answer : (D) Viscous sub-layer

At what value of Prandtl number, conduction is negligible in the turbulent core of a fluid flowing through a heated pipe? (A) 0.5 (B) < 0.5 (C) > 0.6 (D) < 0.1

Description : At what value of Prandtl number, conduction is negligible in the turbulent core of a fluid flowing through a heated pipe? (A) 0.5 (B) < 0.5 (C) > 0.6 (D) < 0.1

Last Answer : (C) > 0.6

How convective heat transfer is effected and on what factors it depends ?

Description : How convective heat transfer is effected and on what factors it depends ?

Last Answer : Convective heat transfer is effected between a solid and fluid by a combination of molecular conduction within the fluid in combination with energy transport resulting from the motion of fluid particles. It depends on boundary layer configuration, fluid properties and temperature difference.

Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Description : Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Last Answer : (C) Exit fluid temperature = wall temperature

__________ is used for measuring the static pressure exerted on the wall by a fluid flowing parallel to the wall in a pipeline. (A) Venturimeter (B) Pressure gauge(C) Pitot tube(D) Orificemeter

Description : __________ is used for measuring the static pressure exerted on the wall by a fluid flowing parallel to the wall in a pipeline. (A) Venturimeter (B) Pressure gauge (C) Pitot tube (D) Orificemeter

Last Answer : (C) Pitot tube

A lake starts freezing because of the cold atmosphere, It will first freeze A. At the bottom B. In the middle part C. At the top surface D. Uniformly throughout the water body

Description : A lake starts freezing because of the cold atmosphere, It will first freeze A. At the bottom B. In the middle part C. At the top surface D. Uniformly throughout the water body

Last Answer : ANSWER: C

A lake starts freezing because of the cold atmosphere. It will first freeze A. At the bottom B. ln the middle pan C. At the top surface (Answer) D. Uniformly throughout the water body

Description : A lake starts freezing because of the cold atmosphere. It will first freeze A. At the bottom B. ln the middle pan C. At the top surface (Answer) D. Uniformly throughout the water body

Last Answer : C. At the top surface (Answer)

The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Description : The velocity profile for a Bingham plastic fluid flowing (under laminar conditions) in a pipe is (A) Parabolic (B) Flat (C) Flat near the wall and parabolic in the middle (D) Parabolic near the wall and flat in the middle

Last Answer : (D) Parabolic near the wall and flat in the middle

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is proportional to the number of times the fluid crosses the bundle between baffles (C) Propagation velocity for travel of heat radiation through vacuum is equal to the velocity of the light (D) The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Description : Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is ... The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Last Answer : (A) Heat transfer by radiation cannot occur across an absolute volume

Use of transverse baffles in a shell and tube heat exchanger is done to increase the (A) Rate of heat transfer (B) Flow velocity (C) Turbulence of shell side fluid (D) All (A), (B) and (C)

Description : Use of transverse baffles in a shell and tube heat exchanger is done to increase the (A) Rate of heat transfer (B) Flow velocity (C) Turbulence of shell side fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Description : Baffles provided on the shell side of a shell and tube heat exchanger are meant for (A) Providing support for the tubes (B) Improving heat transfer (C) Both 'a' & 'b' (D) Preventing the fouling of tubes & stagnation of shell side fluid

Last Answer : C) Both 'a' & 'b'

What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Description : What causes convective acceleration in fluid flow? (A) Steep slope in flow (B) Unsteady nature of flow (C) Non-uniformity of flow (D) Turbulence in flow

Last Answer : (C) Non-uniformity of flow

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

In case of a multipass shell and tube heat exchanger, the temperature drop in the fluid (A) Is inversely proportional to the resistance across which the drop occurs (B) And the wall are proportional to individual resistances (C) And the wall is not related (D) None of these

Description : In case of a multipass shell and tube heat exchanger, the temperature drop in the fluid (A) Is inversely proportional to the resistance across which the drop occurs (B) And the wall are proportional to individual resistances (C) And the wall is not related (D) None of these

Last Answer : (B) And the wall are proportional to individual resistances

In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Description : In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Last Answer : (A) Varies directly as the area and the LMTD

In a gas-liquid absorption column, for obtaining the maximum absorption efficiency (A) Liquid stream should be distributed uniformly (B) Gas stream should be distributed uniformly (C) Both gas as well as liquid streams should be distributed uniformly (D) By passing should be completely avoided

Description : In a gas-liquid absorption column, for obtaining the maximum absorption efficiency (A) Liquid stream should be distributed uniformly (B) Gas stream should be distributed uniformly ... well as liquid streams should be distributed uniformly (D) By passing should be completely avoided

Last Answer : (C) Both gas as well as liquid streams should be distributed uniformly

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

Interference in thin film is mainly because of (a) Division amplitude (b) Division of wave fronts (c) Addition of amplitude (d) Addition of wave fronts

Description : Interference in thin film is mainly because of (a) Division amplitude (b) Division of wave fronts (c) Addition of amplitude (d) Addition of wave fronts

Last Answer : (a) Division amplitude

Interference in thin film is mainly because of A. Division amplitude B. Division of wave fronts C. Addition of amplitude D. Addition of wave fronts

Description : Interference in thin film is mainly because of A. Division amplitude B. Division of wave fronts C. Addition of amplitude D. Addition of wave fronts

Last Answer : A. Division amplitude

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension