A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is exposed to a fluid stream with a convective heat transfer coefficient of 100 W/m2 .K. The Biot number is (A) 5.6 (B) 0.025 (C) 3.5 (D) 0.0035

A metal wire of 0.01 m dia and thermal conductivity 200 W/m.K is

exposed to a fluid stream with a convective heat transfer coefficient of 100

W/m2

.K. The Biot number is

(A) 5.6

(B) 0.025

(C) 3.5

(D) 0.0035

by

1 Answer

Answer :

(B) 0.025

by

Related questions

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the right face is 10 W/m2 .K. At steady state, the temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m-1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is (A) 100 (B) 900 (C) 9000 (D) 10000

Description : One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m-1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is (A) 100 (B) 900 (C) 9000 (D) 10000

Last Answer : (D) 10000

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Description : The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16m is 10 W/m2 . The temperature of the inside wall is - 5°C. The outside wall temperature is (A) 25°C (B) 30°C (C) 35°C (D) 40°C

Last Answer : (C) 35°C

A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Last Answer : (B) 0.1

Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Description : Nusselt number/Biot number varies (A) Inversely with thermal conductivity (B) Directly with heat transfer co-efficient (C) Directly with thermal conductivity (D) Inversely with the dimension of the solid

Last Answer : (A) Inversely with thermal conductivity

The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Description : The critical radius of insulation for a spherical shell is (where, K = thermal conductivity of insulating material h0 = heat transfer coefficient at the outer surface) (A) K/h0 (B) 2K/h0 (C) h0 /K (D) h0 /2K

Last Answer : (B) 2K/h0

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C

The variation of thermal conductivity of a metal with temperature is often correlated using an expression of the form K = K0 + at, where, K is the thermal conductivity and T is the temperature (in °K). The units of 'a' in SI system will be (A) W/m.k (B) W/m (C) W/m.k

Description : The variation of thermal conductivity of a metal with temperature is often correlated using an expression of the form K = K0 + at, where, K is the thermal conductivity and T is the temperature (in °K). The units of 'a' in SI system will be (A) W/m.k (B) W/m (C) W/m.k

Last Answer : (C) W/m.k

Nusselt number is a function of Prandtl number and __________ number of fluid in natural convection heat transfer. (A) Grashoff (B) Biot (C) Stanton

Description : Nusselt number is a function of Prandtl number and __________ number of fluid in natural convection heat transfer. (A) Grashoff (B) Biot (C) Stanton

Last Answer : (A) Grashoff

The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Description : The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

Thermal diffusivity of a material (A) Has the unit m2 /sec (B) Is defined as K/ρ . Cp (C) Is the ratio of thermal conductivity to thermal capacity (D) All (A), (B) and (C)

Description : Thermal diffusivity of a material (A) Has the unit m2 /sec (B) Is defined as K/ρ . Cp (C) Is the ratio of thermal conductivity to thermal capacity (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Last Answer : (A) 7

reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity (C) Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Description : reduction in thermal resistance during heat transfer does not occur in the (A) Convection heat transfer by stirring the fluid and cleaning the heating surface (B) Conduction heat transfer by ... Radiation heat transfer by increasing the temperature and reducing the emissivity (D) None of these

Last Answer : Option C

Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is ‘3k/l’. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?(A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Description : Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l'. If the wall temperature ... wall temperature in degree centigrade? (A) 35.5 (B) 43.75 (C) 81.25 (D) 48.25

Last Answer : (C) 81.25

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Bulk of the convective heat transfer resistance from a hot tube surfaceto the fluid flowing in it, is(A) In the central core of the fluid(B) Uniformly distributed throughout the fluid(C) Mainly confined to a thin film of fluid near the surface(D) None of these

Description : Bulk of the convective heat transfer resistance from a hot tube surfaceto the fluid flowing in it, is (A) In the central core of the fluid (B) Uniformly distributed throughout the fluid (C) Mainly confined to a thin film of fluid near the surface (D) None of these

Last Answer : (C) Mainly confined to a thin film of fluid near the surface

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

In SI units, thermal conductivity is expressed in (A) Watt/m.°K (B) Watt/m2 . °K (C) Watt/m2 . °K (D) Watt/m4 . °K

Description : In SI units, thermal conductivity is expressed in (A) Watt/m.°K (B) Watt/m2 . °K (C) Watt/m2 . °K (D) Watt/m4 . °K

Last Answer : (A) Watt/m.°K

What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Description : What is the unit of thermal conductivity? (A) Kcal/hr. m2 °C (B) Kcal/hr.m.°C (C) Kcal/hr.m (D) Kcal/hr. °C

Last Answer : (B) Kcal/hr.m.°C

Thermal neutrons which are used to cause the fission of U-235 haveenergy __________ eV.(A) < 0.025(B) > 1(C) 1-25(D) > 200

Description : Thermal neutrons which are used to cause the fission of U-235 haveenergy __________ eV. (A) < 0.025 (B) > 1 (C) 1-25 (D) > 200

Last Answer : (A) < 0.025

A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young’s modulus = 1.0 x 10^5 MN/m2 and coefficient of thermal expansion = 0.000012 per degree centigrade. 1. 0.168 cm 2. 0.208 cm 3. 0.288 cm 4. 0.348 cm

Description : A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young’s modulus = 1.0 x 10^5 MN/m2 and coefficient of thermal expansion = 0.000012 per degree centigrade. 1. 0.168 cm 2. 0.208 cm 3. 0.288 cm 4. 0.348 cm

Last Answer : 3. 0.288 cm

Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Description : Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the ... in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Last Answer : (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity

Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Description : Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Last Answer : (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

The void ratio of a soil sample decreases from 1.50 to 1.25 when the pressure is increased from 25 tonnes/m2 to 50 tonnes/m2 , the coefficient of compressibility is (A) 0.01 (B) 0.02 (C) 0.05 (D) 0.001

Description : The void ratio of a soil sample decreases from 1.50 to 1.25 when the pressure is increased from 25 tonnes/m2 to 50 tonnes/m2 , the coefficient of compressibility is (A) 0.01 (B) 0.02 (C) 0.05 (D) 0.001

Last Answer : (A) 0.01

The thermal radiative flux from a surface of emissivity = 0.4 is 22.68 kW/m2 . The approximate surface temperature (K) is (Stefan-Boltzmann constant = 5.67 × 10 -8 W/m2 .K4 )(A) 1000(B) 727(C) 800(D) 1200

Description : The thermal radiative flux from a surface of emissivity = 0.4 is 22.68 kW/m2 . The approximate surface temperature (K) is (Stefan-Boltzmann constant = 5.67 × 10 -8 W/m2 .K4 ) (A) 1000 (B) 727 (C) 800 (D) 1200

Last Answer : (A) 1000

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Description : Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid. (A) 2 to 3 (B) 0.01 to 0.10 (C) 200 to 300 (D) 100 to 1000

Last Answer : A) 2 to 3

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

Velocity of the thermal neutron (< 0.025 eV) used for fission of U-235 is around __________ m/sec. (A) 1 (B) 2200 (C) 3 × 10 11 (D) 9 × 10 21

Description : Velocity of the thermal neutron (< 0.025 eV) used for fission of U-235 is around __________ m/sec. (A) 1 (B) 2200 (C) 3 × 10 11 (D) 9 × 10 21

Last Answer : (B) 2200

In which mode of heat transfer, the Biot number is important? (A) Transient heat conduction (B) Natural convection (C) Forced convection (D) Radiation

Description : In which mode of heat transfer, the Biot number is important? (A) Transient heat conduction (B) Natural convection (C) Forced convection (D) Radiation

Last Answer : (A) Transient heat conduction

jH factor for heat transfer depends upon the __________ number. (A) Biot (B) Nusselt (C) Reynolds (D) Prandtl

Description : jH factor for heat transfer depends upon the __________ number. (A) Biot (B) Nusselt (C) Reynolds (D) Prandtl

Last Answer : (C) Reynolds

What is a measure of the ability of a material to conduct heat?  A. Specific heat capacity  B. Coefficient of thermal expansion  C. Coefficient of thermal conductivity  D. Thermal conductivity

Description : What is a measure of the ability of a material to conduct heat?  A. Specific heat capacity  B. Coefficient of thermal expansion  C. Coefficient of thermal conductivity  D. Thermal conductivity

Last Answer : Thermal conductivity

What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.

Description : What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.

Last Answer : C. 0.635 to 15.24 cm

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is absorbed from the hot reservoir is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Description : The following heat engine produces power of 100,000 kW. The heat engine operates between 800 K and 300 K. It has a thermal efficiency equal to 50% of that of the Carnot engine for the same temperature. The rate at which heat is ... is (A) 100,000 kW (B) 160,000 kW (C) 200,000 kW (D) 320,000 kW

Last Answer : (D) 320,000 kW

Conductance is given by (where, x = thickness, A = heat flow area, K = thermal conductivity.) (A) x/KA (B) KA/x (C) K/Ax (D) A/Kx

Description : Conductance is given by (where, x = thickness, A = heat flow area, K = thermal conductivity.) (A) x/KA (B) KA/x (C) K/Ax (D) A/Kx

Last Answer : (B) KA/x

Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Description : Heat transfer occurs by natural convection because change in temperature causes difference in (A) Viscosity (B) Density (C) Thermal conductivity (D) Heat capacity

Last Answer : (B) Density

Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Description : Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Last Answer : (B) Heat flux

Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Description : Heat transfer rate described by Fourier's law will decrease, if the __________ increases. (A) Thermal conductivity (B) Thickness (C) Temperature difference (D) Heat transfer area

Last Answer : (B) Thickness

In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Description : In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Last Answer : (C) Thermal conductivity

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Convective heat transfer, in which heat is transferred by movement of warmed matter is described by (A) Fourier's law (B) Newton's law of cooling (C) Fick's law (D) None of these

Description : Convective heat transfer, in which heat is transferred by movement of warmed matter is described by (A) Fourier's law (B) Newton's law of cooling (C) Fick's law (D) None of these

Last Answer : (B) Newton's law of cooling

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)