Baffle spacing (A) Is not the same as baffle pitch (B) Should be less than one fifth the diameter of the shell (C) Should be less than the inside diameter of the shell (D) None of these

Baffle spacing

(A) Is not the same as baffle pitch

(B) Should be less than one fifth the diameter of the shell

(C) Should be less than the inside diameter of the shell

(D) None of these

by

1 Answer

Answer :

(C) Should be less than the inside diameter of the shell


by

Related questions

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

In case of a shell and tube heat exchanger, the minimum and maximum baffle spacing is respectively (where, D = inside diameter of the shell) (A) D/5 and D (B) D/2 and 2 D (C) D/4 and 2 D (D) D and 2 D

Description : In case of a shell and tube heat exchanger, the minimum and maximum baffle spacing is respectively (where, D = inside diameter of the shell) (A) D/5 and D (B) D/2 and 2 D (C) D/4 and 2 D (D) D and 2 D

Last Answer : (A) D/5 and D

Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter). (A) 0.2 D (B) 0.5 D (C) 0.66 D (D) 0.80 D

Description : Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter). (A) 0.2 D (B) 0.5 D (C) 0.66 D (D) 0.80 D

Last Answer : (A) 0.2 D

If the baffle spacing in a shell and tube heat exchanger increases, then the Reynolds number of the shell side fluid (A) Remains unchanged (B) Increases (C) Increases or decreases depending on number of shell passes (D) Decreases

Description : If the baffle spacing in a shell and tube heat exchanger increases, then the Reynolds number of the shell side fluid (A) Remains unchanged (B) Increases (C) Increases or decreases depending on number of shell passes (D) Decreases

Last Answer : (D) Decreases

Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Description : Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Last Answer : (B) Flexibility possible in the baffle arrangement

In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Description : In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Last Answer : (A) Gives a higher shell side pressure drop

In a shell and tube heat exchanger, the shell side fluid velocity can’t be changed by changing the (A) Tube layout (B) Tube diameter (C) Tube pitch (D) Number of baffles

Description : In a shell and tube heat exchanger, the shell side fluid velocity can’t be changed by changing the (A) Tube layout (B) Tube diameter (C) Tube pitch (D) Number of baffles

Last Answer : (B) Tube diameter

In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Last Answer : (A) Increases

In a shell and tube heat exchanger, putting a longitudinal baffle across the shell, forces the shell side fluid to pass __________ through the heat exchanger. (A) Once (B) Twice (C) Thrice (D) Four times

Description : In a shell and tube heat exchanger, putting a longitudinal baffle across the shell, forces the shell side fluid to pass __________ through the heat exchanger. (A) Once (B) Twice (C) Thrice (D) Four times

Last Answer : (B) Twice

In surface condensers write role of (i) Water tubes (ii) Shell (iii) Baffle plate (iv) Tube sheet

Description : In surface condensers write role of (i) Water tubes (ii) Shell (iii) Baffle plate (iv) Tube sheet

Last Answer : Function of parts in surface condensers 1. Water tubes- Cooling water flows through it , for convective heat transfer to occur with steam outside the tubes 2. Shell- Outer body, all components are ... and improves heat transfer 4. Tube sheet- All tubes are supported at the end in tube sheet

The diameter of internal flue tubes of a Lancashire boiler is about _______ that of it’s shell a. One fourth b. One third c. Two fifth d. One half

Description : The diameter of internal flue tubes of a Lancashire boiler is about _______ that of it’s shell a. One fourth b. One third c. Two fifth d. One half

Last Answer : c. Two fifth

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

If you like pretty gems that sparkle and shine, I invite you to dig in my virtual mine. My first is purple, fit for a king, My second is green where Dorothy did her thing. My third is red, July's birthstone as well, My fourth is seen in strings and is found inside a shell. My fifth is hard, pure Carbon and expensive to buy, My sixth is Crocodolite, striped like the big cat's eye. Seventh is two words, a man-made fake of April's stone, Eighth is very dark and found at Lightning Ridge alone. Now take from each gem, one letter in its turn, And you will find the stuff for which even the god's yearn. -Riddles

Description : If you like pretty gems that sparkle and shine, I invite you to dig in my virtual mine. My first is purple, fit for a king, My second is green where Dorothy did her thing. My third is red, July's ... gem, one letter in its turn, And you will find the stuff for which even the god's yearn. -Riddles

Last Answer : Ambrosia The gems are: Amethyst Emerald ( Emerald City in the Wizard of Oz ) Ruby Pearl Diamond Tiger's eye Cubic Zirconium (Fake diamond) Black Opal Taking the first letter of Amethyst, second of Emerald, etc.. gives Ambrosia - The food of the gods.

In a shell and tube heat exchanger, the height of 25 percent cut baffles is equal to (where, D = inside diameter of shell). (A) 0.25 D (B) 0.50 D (C) 0.75 D

Description : In a shell and tube heat exchanger, the height of 25 percent cut baffles is equal to (where, D = inside diameter of shell). (A) 0.25 D (B) 0.50 D (C) 0.75 D

Last Answer : (C) 0.75 D

Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Last Answer : Answer: Option B

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Description : The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Last Answer : [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Pick out the wrong statement. (A) Orifice baffles are never used in a shell and tube heat exchanger (B) Pressure drop on the shell side of a heat exchanger depends upon tube pitch also

Description : Pick out the wrong statement. (A) Orifice baffles are never used in a shell and tube heat exchanger (B) Pressure drop on the shell side of a heat exchanger depends upon tube pitch also

Last Answer : (A) Orifice baffles are never used in a shell and tube heat exchanger

Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch

Description : Which is the best tube arrangement (in a shell and tube heat exchanger) if the fluids are clean and non-fouling? (A) Square pitch (B) Triangular pitch (C) Diagonal square pitch chemical-engineering

Last Answer : (B) Triangular pitch

State the four methods of laying of cable. State precautions while laying of underground cable in the situation : (i) Minimum clearance between cable and water pipe line when running in parallel. (ii) Minimum clearance between cable and water pipe line when running in parallel. (iii) If cable is laid through pipe what should be diameter of pipe. (iv) When more than one cable is to be laid in the same trench, what should be minimum spacing between two cables ?

Description : State the four methods of laying of cable. State precautions while laying of underground cable in the situation : (i) Minimum clearance between cable and water pipe line when running in parallel. (ii) ... is to be laid in the same trench, what should be minimum spacing between two cables ?  

Last Answer : (i) Minimum clearance between cable and water pipe line when running in parallel:- 0.5 mtr. (ii) Minimum clearance between cable and water pipe line when running in parallel:- 0.5 mtr ... should be minimum spacing between two cables :- Then minimum 30 cm spacing is provided between 2 cables 

Tower diameter may be decreased by (A) Using higher reflux ratio (B) Use of increased tray spacing (C) Increasing the liquid flow rate (D) Increasing the vapour flow rate

Description : Tower diameter may be decreased by (A) Using higher reflux ratio (B) Use of increased tray spacing (C) Increasing the liquid flow rate (D) Increasing the vapour flow rate

Last Answer : (B) Use of increased tray spacing

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

The equipment used in the extraction of highly corrosive radioactive liquids is (A) Pulse column (B) Spray column (C) Mixer settler (D) Baffle tower

Description : The equipment used in the extraction of highly corrosive radioactive liquids is (A) Pulse column (B) Spray column (C) Mixer settler (D) Baffle tower

Last Answer : (A) Pulse column

Sodium bicarbonate is produced during soda ash manufacture using a __________ tower. (A) Plate (B) Baffle (C) Packed (D) None of these

Description : Sodium bicarbonate is produced during soda ash manufacture using a __________ tower. (A) Plate (B) Baffle (C) Packed (D) None of these

Last Answer : (B) Baffle

Which of the following accessories is provided in the vapor line of an evaporator for removing the entrained liquid? (A) Bleed point (B) Vent (C) Catchall (D) Baffle

Description : Which of the following accessories is provided in the vapor line of an evaporator for removing the entrained liquid? (A) Bleed point (B) Vent (C) Catchall (D) Baffle

Last Answer : (C) Catchall

The maximum spacing of manholes specified by Indian standard in sewers upto 0.3 m diameter is A. 20 m B. 30 m C. 45 m D. 75 m

Description : The maximum spacing of manholes specified by Indian standard in sewers upto 0.3 m diameter is A. 20 m B. 30 m C. 45 m D. 75 m

Last Answer : ANS: C

The spacing of man holes along a straight portion of a sewer is 300 m, the diameter of the sewer may be A. 0.9 cm B. 1.2 m C. 1.5 m D. > 1.5 m

Description : The spacing of man holes along a straight portion of a sewer is 300 m, the diameter of the sewer may be A. 0.9 cm B. 1.2 m C. 1.5 m D. > 1.5 m

Last Answer : ANS: D

What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Description : What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Last Answer : D. 301Ω

ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Description : ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Last Answer : C. length

The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Description : The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal ... column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above

Last Answer : Answer: Option D

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The spacing of stirrups in doubly reinforced beams should be least of the following (i)Least Lateral dimension (ii)Sixteen times the diameter of longitudinal steel (iii)Forty eight times the diameter of transverse reinforcement [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

For end bearing piles, the minimum spacing of piles of diameter ‘d’ shall be a) 3d b) 2d c) 2.5d* d) 5d

Description : For end bearing piles, the minimum spacing of piles of diameter ‘d’ shall be a) 3d b) 2d c) 2.5d* d) 5d

Last Answer : c) 2.5d*

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Description : What is the gain, in dB of a helical antenna with diameter of λ/3, 10 turns at pitch of λ/4, used at 100 MHz? A. 16 B. 41.1 C. 31.4 D. 1.25

Last Answer : A. 16

A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Description : A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Last Answer : (A) Major diameter

The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Description : The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

Last Answer : (A) Major diameter

The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

How To Calculate The Number Of Teeth In A Gear If Given The Module And Pitch Circle Diameter?

Description : How To Calculate The Number Of Teeth In A Gear If Given The Module And Pitch Circle Diameter?

Last Answer :  Pitch = Module* 3.14 (pie value)  Number of teeth = Pitch circle diameter/ pitch

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Description : The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Last Answer : d) 2.5 x d*

What current linguistic oddities will baffle future archaeologists when they stumble upon them?

Description : What current linguistic oddities will baffle future archaeologists when they stumble upon them?

Last Answer : Greatest Of All Time G O A T

If you've seen any "It's Armageddon!!" comments on Facebook, does it baffle you that they lump the eclipse in with the storms and earthquakes?

Description : If you've seen any "It's Armageddon!!" comments on Facebook, does it baffle you that they lump the eclipse in with the storms and earthquakes?

Last Answer : Half of the population has to have lower than 100 iq. Thats how it works.