Description : The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above
Last Answer : (A) Major diameter
Description : Screws are specified by their __________ diameters. (A) Minor (B) Major (C) Pitch (D) None of these
Last Answer : (B) Major
Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter
Last Answer : (B) Inner diameter
Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False
Last Answer : b) False
Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch
Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm
Last Answer : (a) 35 mm
Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point
Last Answer : a) Dog Point
Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt
Last Answer : a) Screw
Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%
Last Answer : a) 50%
Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined
Last Answer : a) decreases
Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False
Description : Efficiency of screw depends upon lead of the screw. a) True b) False
Last Answer : a) True
Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above
Last Answer : d. all of the above
Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt
Last Answer : b. Set screws
Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head
Last Answer : (C) Cap screw with hexagonal socket head
Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface
Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs
Last Answer : (C) Used to prevent relative motion between parts
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew
Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut
Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)
Last Answer : (A) (1 - sinφ)/ (1 + sinφ)
Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False
Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned
Last Answer : b) 40/9
Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed
Last Answer : b) It is measured in uncompressed state
Description : Different types of bearings are designed to operate at different operating speeds. Speed is specified as the maximum (a) rpm (b) metres/second (c) metres/minute (d) metres/hour
Last Answer : (b) metres/second
Description : A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series
Last Answer : c) Medium series
Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above
Last Answer : b. intensity of direct stress
Description : What is the minimum number of round scales in a screw yardage of 100 and pitch 1 mm ?
Last Answer : The number of round scales in a screw yard is 100 and the pitch is 1 mm. Its minimum count is 0.01 mm.
Description : What is the pitch of your laboratory screw gauge?
Last Answer : What is the answer ?
Description : The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above
Last Answer : (A) mean coil diameter / wire diameter
Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (C) Ratio of mean coil diameter to wire diameter
Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring
Last Answer : (D) Square of wire diameter of each spring
Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (D) Force required to produce unit deflection
Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False
Description : Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter
Last Answer : a.the major diameter
Description : Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter
Description : Mark correct option relating to payment of certificate is held by or behalf of minor a) To him personally, if he himself applied for the savings certificate, b) For the use of the minor to any person, ... minor, or where neither parent is alive, to any other guardian of the minor d) All the above
Last Answer : d) All the above
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Last Answer : (a) True
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Last Answer : (b) False
Description : The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7
Last Answer : (b) 5
Description : A sliding contact bearing is operating under stable condition. The pressure developed in oil film is p when the journal rotates at N rpm. The dynamic viscosity of lubricant is μ and effective coefficient of ... to p and f) (d) f is directly proportional to μ and inversely proportional to N
Last Answer : (b) f is directly proportional to μ and N
Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1
Last Answer : (D) 1
Description : The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8
Last Answer : (B) Less than 1
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm
Last Answer : c) 24mm
Description : The diameter of knuckle pin in the knuckle joint is usually... A. 0.5 d B. 0.8 d C. 1.5 d D. d
Last Answer : D. d
Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm
Last Answer : a) 17.27mm