The largest diameter of external or internal screw thread is called (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) None of the above

The largest diameter of external or internal screw thread is called

(A) Major diameter

(B) Minor diameter

(C) Pitch diameter

(D) None of the above
by

1 Answer

Answer :

(A) Major diameter
by

Related questions

A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Description : A screw is specified by (A) Major diameter (B) Minor diameter (C) Pitch diameter (D) Mean diameter

Last Answer : (A) Major diameter

Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Description : Nominal diameter of the screw thread is the same as core diameter. a) True b) False

Last Answer : b) False

Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Description : Most appropriate instrument for measurement of internal and external diameter of a tube is A. vernier callipers B. micrometer screw gauge C. meter rule D. measuring tape

Last Answer : vernier callipers

The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

A screw jack has 4 threads per inch. The mean radius of the thread is 2.338 inches. The mean diameter of the bearing surface under the cap is 3.25 inches. What is the turning moment required to raise the bload of 150 kg ( a.5.61 kg-inch b.50.6 kg-inch c.107 dynes d.30.3 kg-inch e.23.6 kg-inch

Description : A screw jack has 4 threads per inch. The mean radius of the thread is 2.338 inches. The mean diameter of the bearing surface under the cap is 3.25 inches. What is the turning moment required to raise the bload of 150 kg ( a.5.61 kg-inch b.50.6 kg-inch c.107 dynes d.30.3 kg-inch e.23.6 kg-inch

Last Answer : b. 50.6 kg-inch

Under complex or simple loading, strain energy is (a) External work done (b) Internal work done (c) Both internal and external work (d) None

Description : Under complex or simple loading, strain energy is (a) External work done (b) Internal work done (c) Both internal and external work (d) None

Last Answer : (b) Internal work done

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point

Last Answer : a) Dog Point

Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Description : Maximum possible efficiency of a self-locking screw is a) 50% b) 75% c) 66% d) 33%

Last Answer : a) 50%

Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined

Last Answer : a) decreases

Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Description : Efficiency of the screw depends upon helix angle but does not depend on friction angle. a) True b) False

Last Answer : b) False

Efficiency of screw depends upon lead of the screw. a) True b) False

Description : Efficiency of screw depends upon lead of the screw. a) True b) False

Last Answer : a) True

Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Last Answer : d. all of the above

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Description : Allen key is used to tighten (A) Cap screw with hexagonal head (B) Cap screw with fillister head (C) Cap screw with hexagonal socket head (D) Cap screw with flat head

Last Answer : (C) Cap screw with hexagonal socket head

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Last Answer : (A) (1 - sinφ)/ (1 + sinφ)

In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False

Last Answer : b) False

Screws are specified by their __________ diameters. (A) Minor (B) Major (C) Pitch (D) None of these

Description : Screws are specified by their __________ diameters. (A) Minor (B) Major (C) Pitch (D) None of these

Last Answer : (B) Major

Shank is the portion of bolt between the head and the thread. a) True b) False

Description : Shank is the portion of bolt between the head and the thread. a) True b) False

Last Answer : a) True

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Description : Minor principal stress has minimum ________ a. value of shear stress acting on the plane b. intensity of direct stress c. both a. and b. d. none of the above

Last Answer : b. intensity of direct stress

What is the screw thread contact?

Description : What is the screw thread contact?

Last Answer : Need answer

Where can I get a ball screw thread?

Description : Where can I get a ball screw thread?

Last Answer : You can find one online at many different stores. You can try www.precisionscrewthread.com or www.Ball-Screws.Industrial101.com. Ball Screw thread is very advanced and complicated technology. For getting ball screw thread you will need good and advanced CNC machine.

What is the minimum number of round scales in a screw yardage of 100 and pitch 1 mm ?

Description : What is the minimum number of round scales in a screw yardage of 100 and pitch 1 mm ?

Last Answer : The number of round scales in a screw yard is 100 and the pitch is 1 mm. Its minimum count is 0.01 mm.

What is the pitch of your laboratory screw gauge?

Description : What is the pitch of your laboratory screw gauge?

Last Answer : What is the answer ?

how should I calculate the pitch of the metric thread

Description : how should I calculate the pitch of the metric thread

Last Answer : There are tables for that. The pitch is determined by the thread diameter.

Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Description : Mathematically, the ellipse is a curve generated by a point moving in space such that atany position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Last Answer : a.the major diameter

Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Description : Mathematically, the ellipse is a curve generated by a point moving in space such thatat any position the sum of its distances from two fixed points (foci) is constant and equal to a.the major diameter b.the minor diameter c.semi major diameter d.semi-minor diameter

Last Answer : a.the major diameter

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Description : In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Last Answer : (B) The oil film is maintained by supplying oil under pressure

In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Description : In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Last Answer : (A) shorten the spring

For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Description : For two spring connected in series, the force acting on each spring is same and equal to half of the external force. a) True b) False

Last Answer : b) False

Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Last Answer : (D) All three factors

The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)

Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)

Last Answer : 4. 2(shaft diameter)

The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)

Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)

Last Answer : (D) 2 (shaft diameter)

A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False

Last Answer : (a) True

A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Last Answer : (a) 35 mm

Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False

Last Answer : (b) False

The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7

Description : The needle rollers are a maximum of _______ millimeter in diameter. (a) 4 (b) 5 (c) 6 (d) 7

Last Answer : (b) 5