The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

The Minimum bar spacing should not be less than
[ A ] Diameter of the largest bar
[ B ] Maximum size of aggregate
[ C ] Greater of diameter of the largest bar and maximum size of aggregate
[ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm
by

1 Answer

Answer :

[ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm
by

Related questions

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these

Last Answer : Answer: Option B

If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm

Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm (C) The material having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Description : Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm ( ... having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Last Answer : Answer: Option D

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Last Answer : Answer: Option D

The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 m

Description : The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 mm

Last Answer : Answer: Option B

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Description : The maximum of spacing of side face reinforcement shall not exceed [ A ] 300 mm [ B ] Web thickness [ C ] Lesser of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Lesser of (a) and (b)

The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Last Answer : [ D ] Smaller of five times the effective depth and 450 mm

Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Description : Minimum cover to longitudinal steel in a column should be (if the diameter of bar, Ø> 12mm) [ A ] 25 mm [ B ] 30 mm [ C ] 40 mm [ D ] 50 mm

Last Answer : [ C ] 40 mm

For the construction of cement concrete floor, the maximum permissible size of aggregate, is (A) 4 mm (B) 6 mm (C) 8 mm (D) 10 mm

Description : For the construction of cement concrete floor, the maximum permissible size of aggregate, is (A) 4 mm (B) 6 mm (C) 8 mm (D) 10 mm

Last Answer : Answer: Option D

The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Description : The diameter of ties in a column should be (A) More than or equal to one fourth of diameter of main bar (B) More than or equal to 5 mm (C) More than 5 mm but less than one-fourth of diameter of main bar (D) More than 5 mm and also more than one-fourth of diameter of main bar

Last Answer : Answer: Option D

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

The maximum diameter of a bar used in a ribbed slab, is (A) 12 mm (B) 6 mm (C) 20 mm (D) 22 mm

Description : The maximum diameter of a bar used in a ribbed slab, is (A) 12 mm (B) 6 mm (C) 20 mm (D) 22 mm

Last Answer : Answer: Option D

The minimum clear cover for R.C.C. columns shall be (A) Greater of 40 mm or diameter (B) Smaller of 40 mm or diameter (C) Greater of 25 mm or diameter (D) Smaller of 25 mm or diameter

Description : The minimum clear cover for R.C.C. columns shall be (A) Greater of 40 mm or diameter (B) Smaller of 40 mm or diameter (C) Greater of 25 mm or diameter (D) Smaller of 25 mm or diameter

Last Answer : Answer: Option C

As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Description : As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Last Answer : [ B ] 1/4 of minimum thickness of member

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Last Answer : (d) All the above

In case of a shell and tube heat exchanger, the minimum and maximum baffle spacing is respectively (where, D = inside diameter of the shell) (A) D/5 and D (B) D/2 and 2 D (C) D/4 and 2 D (D) D and 2 D

Description : In case of a shell and tube heat exchanger, the minimum and maximum baffle spacing is respectively (where, D = inside diameter of the shell) (A) D/5 and D (B) D/2 and 2 D (C) D/4 and 2 D (D) D and 2 D

Last Answer : (A) D/5 and D

An aggregate is known as cyclopean aggregate if its size is more than (A) 4.75 mm (B) 30 mm (C) 60 mm (D) 75 mm

Description : An aggregate is known as cyclopean aggregate if its size is more than (A) 4.75 mm (B) 30 mm (C) 60 mm (D) 75 mm

Last Answer : Answer: Option D

An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 m

Description : An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 mm

Last Answer : Answer: Option D

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm

Description : The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Description : The maximum spacing of main steel in slabs has been limited to [ A ] 250 mm [ B ] 300 mm [ C ] 450 mm [ D ] 500 mm

Last Answer : [ B ] 300 mm

For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Description : For a ribbed slab (A) Clear spacing between ribs shall not be greater than 4.5 cm (B) Width of the rib shall not be less than 7.5 cm (C) Overall depth of the slab shall not exceed four times the breadth of the rib (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m diameter are designed as running 2/3rd or 3/4th full at maximum discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Description : Pick up the correct statement from the following: A. The sewer pipes of sizes less than 0.4 m diameter are designed as running full at maximum discharge B. The sewer pipes of sizes greater than 0.4 m ... discharge C. The minimum design velocity of sewer pipes is taken as 0.8 m/sec D. All the above

Last Answer : ANS: D

In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Description : In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be (A) Less than 300 mm (B) Between 300 mm and 750 mm (C) Between 750 mm and 1 m (D) Greater than 1 m

Last Answer : (B) Between 300 mm and 750 mm

Stoke's law is valid only if the size of particle is (A) Less than 0.0002 mm (B) Greater than 0.2 mm (C) Between 0.2 mm and 0.0002 mm (D) All of the above

Description : Stoke's law is valid only if the size of particle is (A) Less than 0.0002 mm (B) Greater than 0.2 mm (C) Between 0.2 mm and 0.0002 mm (D) All of the above

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by a straight horizontal line on the grading curve (C) The omission of a certain size of aggregate in concrete increases the workability but also increases the liability to segregation (D) All the above

Description : Pick up the correct statement from the following: (A) Continuous grading is not necessary for obtaining a minimum of air voids (B) The omission of a certain size of aggregate is shown by ... in concrete increases the workability but also increases the liability to segregation (D) All the above

Last Answer : Answer: Option D

The minimum particle size of fine aggregate is (a) 0.0075mm (b) 0.075mm (c)0.75mm (d)0.95m

Description : The minimum particle size of fine aggregate is (a) 0.0075mm (b) 0.075mm (c)0.75mm (d)0.95m

Last Answer : (b) 0.075mm

State the four methods of laying of cable. State precautions while laying of underground cable in the situation : (i) Minimum clearance between cable and water pipe line when running in parallel. (ii) Minimum clearance between cable and water pipe line when running in parallel. (iii) If cable is laid through pipe what should be diameter of pipe. (iv) When more than one cable is to be laid in the same trench, what should be minimum spacing between two cables ?

Description : State the four methods of laying of cable. State precautions while laying of underground cable in the situation : (i) Minimum clearance between cable and water pipe line when running in parallel. (ii) ... is to be laid in the same trench, what should be minimum spacing between two cables ?  

Last Answer : (i) Minimum clearance between cable and water pipe line when running in parallel:- 0.5 mtr. (ii) Minimum clearance between cable and water pipe line when running in parallel:- 0.5 mtr ... should be minimum spacing between two cables :- Then minimum 30 cm spacing is provided between 2 cables 

Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter). (A) 0.2 D (B) 0.5 D (C) 0.66 D (D) 0.80 D

Description : Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter). (A) 0.2 D (B) 0.5 D (C) 0.66 D (D) 0.80 D

Last Answer : (A) 0.2 D

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

Hazen’s formula VS = 418 (GS – Gw)d [(3T + 70)/100] is used for the settlement velocity of the particles of diameter A. Less than 0.01 mm B. Less than 0.05 mm C. Less than 0.1 mm D. Greater than 0.1 mm

Description : Hazen’s formula VS = 418 (GS – Gw)d [(3T + 70)/100] is used for the settlement velocity of the particles of diameter A. Less than 0.01 mm B. Less than 0.05 mm C. Less than 0.1 mm D. Greater than 0.1 mm

Last Answer : ANS: D

For end bearing piles, the minimum spacing of piles of diameter ‘d’ shall be a) 3d b) 2d c) 2.5d* d) 5d

Description : For end bearing piles, the minimum spacing of piles of diameter ‘d’ shall be a) 3d b) 2d c) 2.5d* d) 5d

Last Answer : c) 2.5d*

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm

Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that  stress in the wire does not exceed 100 N/mm2  is:  (A) 4.0 mm  (B) 4.5 mm  (C) 5.0 mm  (D) 5.5 mm

Last Answer : (C) 5.0 mm 

In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness

If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N

Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in  diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive  load to remove the clearance, is  (A) 25 N  (B) 30 N  (C) 35 N  (D) 40 N 

Last Answer : (C) 35 N 

The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Description : The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known (A) Liquid limit (B) Plastic limit (C) Shrinkage limit (D) Permeability limit

Last Answer : (B) Plastic limit

The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Description : The minimum diameter of longitudinal bars in a column is (A) 6 mm (B) 8 mm (C) 12 mm (D) 16 mm

Last Answer : Answer: Option C

The minimum diameter of longitudinal steel should be [ A ] 10 mm [ B ] 12 mm [ C ] 16 mm [ D ] 20 mm

Description : The minimum diameter of longitudinal steel should be [ A ] 10 mm [ B ] 12 mm [ C ] 16 mm [ D ] 20 mm

Last Answer : [ B ] 12 mm

End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Description : End anchorage of bars is taken as the greater of [ A ] Effective depth or 12 times the diameter of bar [ B ] Effective depth or 16 times the diameter of bar [ C ] Effective depth of 24 times the diameter of bar [ D ] Effective depth of 48 times the diameter of bar

Last Answer : [ A ] Effective depth or 12 times the diameter of bar