If a force of 50 N is applied across the cross-sectional area of 5 × 10- 7m2 then stress applied on it is A. 1 × 108 Pa B. 20 Pa C. 50 Pa D. 100 Pa

If a force of 50 N is applied across the cross-sectional area of 5 × 10-

7m2 then stress applied on it is

A. 1 × 108 Pa

B. 20 Pa

C. 50 Pa

D. 100 Pa
by

1 Answer

Answer :

. 1 × 108 P
by

Related questions

Stress is force applied on A. volume B. cross sectional area C. unit length D. across diagonal

Description : Stress is force applied on A. volume B. cross sectional area C. unit length D. across diagonal

Last Answer : cross sectional area

is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) (B) f = (A/P) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)

Last Answer : Answer: Option C

is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)

Last Answer : Answer: Option C

If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Description : The Modulus of Elasticity for a material refers to: w) the ability of a material to resist corrosion x) the ratio of stress over strain y) the maximum load over the cross sectional area z) none of the above

Last Answer : ANSWER: X -- THE RATIO OF STRESS OVER STRAIN

A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N.

Description : A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N.

Last Answer : A steel wire having cross sectional area 1.2 mm is stretched by a force of 120 N. If a ... is produced in the wire, calculate the Poisson's ratio.

Normal force acting per unit cross sectional area is called A. weight B. pressure C. volume D. friction

Description : Normal force acting per unit cross sectional area is called A. weight B. pressure C. volume D. friction

Last Answer : pressure

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Description : Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1

Last Answer : 0.015 mm s-1

If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P

Description : If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre-stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is (A) P/A (B) A/P (C) P/2A (D) 2A/P

Last Answer : Answer: Option A

In a reinforced concrete column, the cross –sectional area of steel bar is as and that of concrete ia AC; the equivalent area of the section n terms of concrete is equal to. (a) As+mAc (b) Ac+mAs (c) As-mAc (d) Ac-mAs

Description : In a reinforced concrete column, the cross –sectional area of steel bar is as and that of concrete ia AC; the equivalent area of the section n terms of concrete is equal to. (a) As+mAc (b) Ac+mAs (c) As-mAc (d) Ac-mAs

Last Answer : (b) Ac+mAs

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

16. Surface tension force is the product of surface tension per unit length and cross-sectional area of flow. A) Correct B) Incorrect

Description : 16. Surface tension force is the product of surface tension per unit length and cross-sectional area of flow. A) Correct B) Incorrect

Last Answer : B

Cross sectional area of catch water drain should not be more than a) 0 .75 square meter* b) 0. 90 square meter c) 0. 80 square meter d). 50 square meter

Description : Cross sectional area of catch water drain should not be more than a) 0 .75 square meter* b) 0. 90 square meter c) 0. 80 square meter d). 50 square meter

Last Answer : a) 0 .75 square meter*

The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross- sectional area of...

Description : The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is (A) 100 (B) 200 (C) 222 (D) 400

Last Answer : The primary turns of a 444 V/222 V, 50 Hz single-phase transformer with a core cross-sectional area of 100 cm2, and a maximum flux density of 1.0 T is 200

On the basis of time, research can be classified as, (i) Qualitative versus Quantitative (ii) Pure versus applied research (iii) Cross-sectional versus longitudinal research (iv) None of the above

Description : On the basis of time, research can be classified as, (i) Qualitative versus Quantitative (ii) Pure versus applied research (iii) Cross-sectional versus longitudinal research (iv) None of the above

Last Answer : (iii) Cross-sectional versus longitudinal research

On the basis of contributions made, all the researches can be classified as Options: A) Fundamental-Applied-Action Research B) Experimental-Historical-Philosophical C) Longitudinal and Cross-sectional D) None of the above

Description : On the basis of contributions made, all the researches can be classified as Options: A) Fundamental-Applied-Action Research B) Experimental-Historical-Philosophical C) Longitudinal and Cross-sectional D) None of the above

Last Answer : A) Fundamental-Applied-Action Research 

A conducting wire of cross-sectional area `1 cm^(2)` has `3 xx 10^(23)` charge carriers per m3. If wire carries a current of `24 mA`, then drift veloc

Description : A conducting wire of cross-sectional area `1 cm^(2)` has `3 xx 10^(23)` charge carriers per m3. If wire carries a current of `24 mA`, then drift veloc

Last Answer : A conducting wire of cross-sectional area `1 cm^(2)` has `3 xx 10^(23)` charge carriers per m3. If wire carries ... 3)ms^(-1)` D. `5xx10^(-6)ms^(-1)`

A tube of uniform cross sectional sectional area `1 cm^(2)` is closed at one end with semi permeable membrane. A solution having 6g glucose per 100 ml

Description : A tube of uniform cross sectional sectional area `1 cm^(2)` is closed at one end with semi permeable membrane. A solution having 6g glucose per 100 ml

Last Answer : A tube of uniform cross sectional sectional area `1 cm^(2)` is closed at one end with semi permeable membrane. A ... k^(-1)`, density of Hg=13.8 g/cc)

Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: (1) increases (2) decreases (3) stays the same (4) none of the above

Description : Water flows through a horizontal pipe at a constant volumetric rate. At a location where the cross sectional area decreases, the velocity of the fluid: (1) increases (2) decreases (3) stays the same (4) none of the above

Last Answer : (1) increases

Change in length and cross-sectional area of metal wire changes A. current B. voltage C. resistance D. magnetic effect

Description : Change in length and cross-sectional area of metal wire changes A. current B. voltage C. resistance D. magnetic effect

Last Answer : resistance

E.M.F for a coil depends upon A. the cross sectional area B. no. of turns of wire C. the magnitude of magnetic flux density D. all of above

Description : E.M.F for a coil depends upon A. the cross sectional area B. no. of turns of wire C. the magnitude of magnetic flux density D. all of above

Last Answer : all of above

The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Last Answer : [ A ] 0.12 percent of gross cross sectional area

The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Description : The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Last Answer : (A) 1.118

A couple applied to a flywheel of mass 5 kg and of radius of gyration 20 cm produces an angular acceleration of 4 radians/sec2. The torque applied in dyne cm is a.8 x 104 b.8 x 106 c.8 x 107 d.8 x 108 e.8 x 1010

Description : A couple applied to a flywheel of mass 5 kg and of radius of gyration 20 cm produces an angular acceleration of 4 radians/sec2. The torque applied in dyne cm is a.8 x 104 b.8 x 106 c.8 x 107 d.8 x 108 e.8 x 1010

Last Answer : b. 8 x 106

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Description : In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Last Answer : ANS: D

A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Description : A Bingham fluid of viscosity μ = 10 Pa.s and yield stress, τ0 = 10 KPa, is shared between flat parallel plates separated by a distance of 10 -3 m. The top plate is moving with a velocity of 1 m/s. The shear stress on the plate is (A) 10 KPa (B) 20 KPa (C) 30 KPa (D) 40 KPa

Last Answer : (B) 20 KPa

A 10 kilogram mass rests on a horizontal frictionless surface. A horizontal force of 5 Newtons is applied to the mass. After the force has been applied for 1 second, the velocity of the mass is: w) 0 meters per second x) 0.5 meters per second y) 5 meters per second z) 50 meters per second

Description : A 10 kilogram mass rests on a horizontal frictionless surface. A horizontal force of 5 Newtons is applied to the mass. After the force has been applied for 1 second, the velocity of the mass is: w) 0 meters per second x) 0.5 meters per second y) 5 meters per second z) 50 meters per second

Last Answer : ANSWER: X -- 0.5 METERS PER SECOND

A current of 2 A is flowing through a wire of length 4 m and cross-sectional area `1 mm^(2)`. If each cubic metre of the wire contains `10^(29)` free

Description : A current of 2 A is flowing through a wire of length 4 m and cross-sectional area `1 mm^(2)`. If each cubic metre of the wire contains `10^(29)` free

Last Answer : A current of 2 A is flowing through a wire of length 4 m and cross-sectional area `1 mm^(2)` ... taken by an electron to cross the length of the wire.

What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^(2)` if the current is 10 A. Assume there

Description : What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^(2)` if the current is 10 A. Assume there

Last Answer : What is the drift velocity of electrons in a copper conductor having a cross-sectional area of `5xx10^(-6) m^( ... `8.0xx10^(28) "electrons"//m^(3)`.

The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10^(-4) m//s` when a certain potential differ

Description : The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10^(-4) m//s` when a certain potential differ

Last Answer : The free electrons of a copper wire of cross-sectional area `10^(-6) m^(2)` acquire a drift velocity of `10 ... is `8.5xx10^(28) "electrons"//m^(3)`.

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

An object is displaced by 10 meters in the direction of applied force. If the applied force is 75 N, What is the work done by the force? -Physics

Description : An object is displaced by 10 meters in the direction of applied force. If the applied force is 75 N, What is the work done by the force? -Physics

Last Answer : (d) 750 joule

Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Description : Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Last Answer : 0.20 A

X and y are two trains of length 500m and 400m run on parallel lines. When they run in the same direction it will take 60 sec to cross each other. When they run in opposite direction, it will take 20 sec to cross each other. Find the speed of 2 trains (in km/hr) A) 116 and 42 km/hr B) 54 and 78km/hr C) 104 and 60km/hr D) 108 and 54km/hr

Description : X and y are two trains of length 500m and 400m run on parallel lines. When they run in the same direction it will take 60 sec to cross each other. When they run in opposite direction, it will take 20 sec to cross each ... ) A) 116 and 42 km/hr B) 54 and 78km/hr C) 104 and 60km/hr D) 108 and 54km/hr

Last Answer :  ANSWER : D Explanation:  Let the speed of 2 trains be a1 and a2  Total distance covered to cross each other = (500 + 400)m  = 900m  When they run in the same direction,  Relative speed = a1 - a2  = 900 /60 ... hr  a 2= (15 * 18 / 5)m/s  = 54km/hr  Speed of two trains are 108 and 54 km/hr

Apiece of sawn timber whose cross-sectional dimensions exceed 5 cm, in one direction and 20 cm in the other direction, is called a (A) Cant (B) Deal (C) Baulk (D) Strip

Description : Apiece of sawn timber whose cross-sectional dimensions exceed 5 cm, in one direction and 20 cm in the other direction, is called a (A) Cant (B) Deal (C) Baulk (D) Strip

Last Answer : Answer: Option C

A charge of 10μC and 14.4 μC are 12 cm apart, the force between them is: (a) 9 × 105 N (b) 9 × 107 N (c) 90 N (d) 108 × 107 N

Description : A charge of 10μC and 14.4 μC are 12 cm apart, the force between them is: (a) 9 × 105 N (b) 9 × 107 N (c) 90 N (d) 108 × 107 N

Last Answer : (c) 90 N

One bar is equal to – (1) 10 ³ Pa (1) 100 Pa (2) 10 ⁵ Pa (3) 10 ⁴ Pa (4)

Description : One bar is equal to – (1) 10 ³ Pa (1) 100 Pa (2) 10 ⁵ Pa (3) 10 ⁴ Pa (4)

Last Answer : (3) 10 ⁵ Pa Explanation: The bar is a non-Si unit of pressure. It is defined by the IUPAC as exactly equal to 100,000 Pa or 1O Pa.

A car is moving along a straight horizontal road at a speed of 20 meters per second. The brakes are applied and a constant force of 5000 Newtons decelerates the car to a stop in 10 seconds. The mass of the car is: w) 1250 kilograms x) 2500 kilograms y) 5000 kilograms z) 10,000 kilograms

Description : A car is moving along a straight horizontal road at a speed of 20 meters per second. The brakes are applied and a constant force of 5000 Newtons decelerates the car to a stop in 10 seconds. The mass of the car is: w) 1250 kilograms x) 2500 kilograms y) 5000 kilograms z) 10,000 kilograms

Last Answer : ANSWER: X -- 2500 KILOGRAMS

Each 1 kg mass experiences force of A. 7 N B. 9.81 N C. 20 N D. 100 N

Description : Each 1 kg mass experiences force of A. 7 N B. 9.81 N C. 20 N D. 100 N

Last Answer :  9.81 N

A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the density of the charge-carriers in the wire

Description : A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the density of the charge-carriers in the wire

Last Answer : A current of 5 ampere is passing through a metallic wire of cross-sectional area `4xx10^(-6) m^(2)`. If the ... ms^(-1)` D. `1xx10^(-2)ms^(-1)`

The discharge through an external mouthpiece is given by (where a = Cross-sectional area of the mouthpiece, and H = Height of liquid above the mouthpiece) (A) 0.855 a. gH) (B) 1.855 aH. g) (C) 1.585 a. gH) (D) 5.85 aH. g)

Description : The discharge through an external mouthpiece is given by (where a = Cross-sectional area of the mouthpiece, and H = Height of liquid above the mouthpiece) (A) 0.855 a. gH) (B) 1.855 aH. g) (C) 1.585 a. gH) (D) 5.85 aH. g)

Last Answer : Answer: Option A

A rectangle-shaped open-to-sky tank of water has a length of 2 m and a width of 1 m. If the atmospheric pressure is assumed to be 100 kPa and thickness of the tank walls is assumed to be negligible, the force exerted by the atmosphere on the surface of water is A. 20 kN B. 50 kN C. 100 kN D. 200 kN

Description : A rectangle-shaped open-to-sky tank of water has a length of 2 m and a width of 1 m. If the atmospheric pressure is assumed to be 100 kPa and thickness of the tank walls is assumed to be negligible, the force exerted by ... of water is A. 20 kN B. 50 kN C. 100 kN D. 200 kN

Last Answer : 200 kN

A weight of 50 N is suspended from a spring of stiffness 4000N/m and subjected to a harmonic force of magnitude 60N and frequency 60 Hz. what will be the static displacement of the spring due to maximum applied force A. 0.015m B. 0.15 m C. 15 m D. 150m

Description : A weight of 50 N is suspended from a spring of stiffness 4000N/m and subjected to a harmonic force of magnitude 60N and frequency 60 Hz. what will be the static displacement of the spring due to maximum applied force A. 0.015m B. 0.15 m C. 15 m D. 150m

Last Answer : B. 0.15 m

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

Calculate the work done in stretching a steel wire of length 2m and cross sectional area 0.0225 mm^2

Description : Calculate the work done in stretching a steel wire of length 2m and cross sectional area 0.0225 mm^2

Last Answer : Calculate the work done in stretching a steel wire of length 2m and cross sectional area 0.0225mm2 when a load ... 's modulus of steel= 2 1011 N/m2]