Explain taper turning by using swiveling compound rest.

Explain taper turning by using swiveling compound rest.
by

1 Answer

Answer :

Taper Turning Method by Swiveling the Compound Rest:

electronics2electrical.com 683 - .jpg

This method employs the principle of turning taper by rotating the work piece on the lathe axis and feeding the tool at an angle to the axis of rotation of the work piece. The tool mounted on the compound rest is attached on a circular base (Swivel plate), graduated in degree, which may be swiveled and clamped at any desired angle. Once the compound rest is set at the desired angle half the taper angle, rotation of the compound slide screw will cause the tool to be fed at the angle and generate a corresponding taper. The movement of tool is controlled by hand.

by

Related questions

Explain the taper turning method by swiveling the compound rest method.

Description : Explain the taper turning method by swiveling the compound rest method. 

Last Answer : Taper turning by swiveling compound rest: Figure below shows the arrangement made for the taper turning by swiveling the compound rest. This method employs the principle of turning taper by rotating the ... is controlled by hand. Following formula is used for calculation of taper turning.  

How do I gauge my ears to a 00g using a size 0g taper?

Description : How do I gauge my ears to a 00g using a size 0g taper?

Last Answer : Take your tape and roll it up – convert size og to cm- then make your roll to that

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Describe various phase transformations of iron after cooling at various rates using TTT diagram.

Description : Describe various phase transformations of iron after cooling at various rates using TTT diagram.

Last Answer : TTT is Time-Temperature-Transformation diagram. It shows the microstructures resulting from non-equilibrium cooling which is not possible on Fe-c diagram. It shows various microstructures of steels depending upon cooling rate & also the temperature and time taken for each transformation.

Explain keyway milling process with standard milling cutters.

Description : Explain keyway milling process with standard milling cutters.

Last Answer : Keyway Milling Operation: This milling process produce keyway slot. The cutter use if thin size. This operation suited for long keyways. The position of the cutter is shown in figure. Standard ... and then the cut is taken. Woodruff key is produced by using a woodruff key slot cutter.

Explain the importance of various machining parameters in improving tool life.

Description : Explain the importance of various machining parameters in improving tool life.

Last Answer : Various Machining Parameters in Improving Tool Life are: 1. Hardness and machinability of the metal to be machined. 2. Quality of heat treatment if it is steel tool. 3. Whether machining is to be done with or ... tool. 6. Depth of cut. 7. Feed to be given to the tool. 8. Cutting Speed.

Explain single point cutting tool nomenclature with sketch.

Description : Explain single point cutting tool nomenclature with sketch.

Last Answer : Single Point Cutting Tool Nomenclature: 1. Shank: The main body of the tool is known as shank. It is the backward part of tool which is hold by tool post. 2. Face: The top surface tool ... piece. 12. Nose Radius: The intersecting area of both cutting edges is known as nose of the tool.

Explain any four defects in casting and give remedies of it.

Description : Explain any four defects in casting and give remedies of it.

Last Answer : Casting Defects Remedies Shifts By ensuring proper alignment of the pattern or die part, moulding boxes, correct mounting of patterns on pattern plates, and checking of flasks, locating ... or replace core boxes, Repairs or replace core prints, Proper setting of cores. 

Explain induction hardening process and give it’s applications.

Description : Explain induction hardening process and give it’s applications.

Last Answer : Induction Hardening: It involves heating thin surface layer of hardenable steel and cast iron components by means of a high frequency induced current to a temperature within or above the transformation range ... [2] Crankshaft,[3] Spur gear,[4] Camshaft, [5] Cams, [6] Automobile parts 

Explain the effect of nickel, chromium, silicon, molybdenum addition on the properties of steel.

Description : Explain the effect of nickel, chromium, silicon, molybdenum addition on the properties of steel.

Last Answer : 1) Effect of Nickel as alloying Element: i) Provides toughness, corrosion resistance, and deep hardening. ii) Increases resistance to impact iii ) Improves tensile strength 2. Effect ... temper brittleness. iv) increases strength. V0 Mo-carbides help increase creepresistance at elevated temps

Explain the importance of pattern allowances and state various pattern allowances.

Description : Explain the importance of pattern allowances and state various pattern allowances. 

Last Answer : Pattern Allowances are Important Because: 1. Solid contraction can be reduced by providing more allowance on patterns. 2. When a pattern is drawn from a mould, there is always some ... allowance iii. Machining allowance iv. Distortion or camber allowance v. Shake allowance / rapping allowance

Explain Gang Milling Process.

Description : Explain Gang Milling Process.

Last Answer : Gang Milling Operation: It involves the use of a combination of more than two cutters, mounted on a common arbor, for milling a number of flat horizontal and vertical surfaces of a work piece ... . The cutting speed of a gang of cutters is calculated from the cutter of the largest diameter. 

Explain importance of Tool Life

Description : Explain importance of Tool Life

Last Answer : Tool life is a volume of material removed by a machining tool during its total usage span. The volume may be in cubic mm or cubic cm at a standard cutting speed. Importance of Tool Life: 1 ... will be profit in manufacturing processes. 2. Time saved in frequent tool changing. 3. Low inventory.

Draw Cooling Curve for Pure Iron and explain.

Description : Draw Cooling Curve for Pure Iron and explain.

Last Answer : Cooling Curve for Pure Iron: Figure: Cooling Curve for Pure Iron

Explain induction hardening process.

Description : Explain induction hardening process.

Last Answer : Induction hardening - The process of the surface hardening by inductive heating is known as induction hardening. A high frequency current is passed through the inductor blocks which surround the gear to ... time, the circuit is opened and water is sprayed immediately on the surface for quenching.

What chemical changes happen when wax taper is used to light a firework?

Description : What chemical changes happen when wax taper is used to light a firework?

Last Answer : Feel Free to Answer

What is a cylinder taper?

Description : What is a cylinder taper?

Last Answer : What is the answer ?

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Description : In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Last Answer : (d) 25°

Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Description : Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Last Answer : (c) Needle roller bearing

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Description : Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Last Answer : c) Take low radial and heavy loads

Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Description : Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Last Answer : c) Both axial and thrust loads

The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Description : The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Last Answer : b) disagree

Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Description : Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Last Answer : D. 1 in 48 to 1 in 24

Taper is made cotter and slot on both the side. A. Yes B. No

Description : Taper is made cotter and slot on both the side. A. Yes B. No

Last Answer : B. No

Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Description : Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Last Answer : A. Top side only

Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Description : Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Last Answer : C. 1 in 100

The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance. (A) Casting (B) Pattern (C) Draft (D) Distortion

Description : The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance. (A) Casting (B) Pattern (C) Draft (D) Distortion

Last Answer : C) Draft

A single lane carriage way whenever changes to two-lane carriage way, is affected through a taper of (A) 1 in 10 (B) 1 in 15 (C) 1 in 20 (D) 1 in 15 to 1 in 20

Description : A single lane carriage way whenever changes to two-lane carriage way, is affected through a taper of (A) 1 in 10 (B) 1 in 15 (C) 1 in 20 (D) 1 in 15 to 1 in 20

Last Answer : Answer: Option D

The taper of precast concrete pile should not be more than (A) 1 cm per metre length (B) 2 cm per metre length (C) 4 cm per metre length (D) 5 cm per metre length

Description : The taper of precast concrete pile should not be more than (A) 1 cm per metre length (B) 2 cm per metre length (C) 4 cm per metre length (D) 5 cm per metre length

Last Answer : Answer: Option B

What Is The Use Of Taper Roller Bearing?

Description : What Is The Use Of Taper Roller Bearing?

Last Answer : A taper roller bearing is used to carry heavy loads because it has taper rollers instead of plain cylindrical rollers.

Flexibility of the retentive clasp arm does not relate to: A. Length B. Cross section C. Material D. Degree of taper E. Under cut area

Description : Flexibility of the retentive clasp arm does not relate to: A. Length B. Cross section C. Material D. Degree of taper E. Under cut area

Last Answer : E. Under cut area

Flexibility of the retentive clasp arm depends on: A. Length B. Cross section C. Material D. Degree of taper E. All of the above

Description : Flexibility of the retentive clasp arm depends on: A. Length B. Cross section C. Material D. Degree of taper E. All of the above

Last Answer : E. All of the above

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

State any two advantages and disadvantages of foundry process

Description : State any two advantages and disadvantages of foundry process

Last Answer : Following are the advantages of foundry process:  i. It one of the most versatile manufacturing process. ii. Castings provide uniform directional properties. iii. Intricate shaped parts can be ... casting process, skilled operators are required. v. Internal defects are not identified easily. 

Define phase and phase diagram

Description : Define phase and phase diagram

Last Answer : Phase : A phase is defined as a homogeneous part of a system that has uniform physical and chemical properties. Pure metal is considered to be a phase. Phase diagrams are the diagrams which ... It also helps in understanding the phenomenon that occur during rapid heating and cooling of the alloy.

State the need of advanced material in making of automobile components.

Description : State the need of advanced material in making of automobile components.

Last Answer : The general finding highlights the need for developing material systems methodology and for approaching research issues in terms of material life cycles.  Improved materials and material ... Modeling of material system. Materials system research, Lightweight material for body structure.

Describe the construction and working of bench drilling machine with block diagram.

Description : Describe the construction and working of bench drilling machine with block diagram.

Last Answer : Major Parts of Bench Drilling Machine : Functions of Parts: i. Base: It supports the column, which in turn, support the table and head etc. ii. Spindle: It is made up of alloy steel. It ... : It is vertical round or box section, which rests on the base and supports the head and the table.

Classify various types of Milling Machines. List major parts of Universal Milling Machine.

Description : Classify various types of Milling Machines. List major parts of Universal Milling Machine.

Last Answer : Classification of Milling Machine:- 1) Column and Knee Type Milling Machine a. Plain or Horizontal Milling Machine b. Hand Milling Machine c. Vertical Milling Machine d. Universal Milling Machine e. Omniversal ... Base [2]Column [3]Knee [4]Saddle [5]Table [6]Overhanging arm [7]Spindle [8]Arbor

Differential clearly between Orthogonal and Oblique Cutting

Description : Differential clearly between Orthogonal and Oblique Cutting

Last Answer : Orthogonal Cutting Oblique Cutting The cutting edge of the tool is perpendicular to the cutting velocity factor The cutting edge is inclined at an angle I' with the normal to the cutting velocity ... cutting edge in action. More than one cutting edges are in action

Describe Shell Molding Process with applications.

Description : Describe Shell Molding Process with applications.

Last Answer : Shell Moulding: It is a process in which the sand mixed with a thermosetting resin is allowed to come into contact with a heated metallic pattern plate, so that a thin and a strong shell of mould is ... 6. Gear blanks 7. Small crank shafts 8. Refrigerator valve plate 9. Chain seat bracket

Differentiate Hardening and Tempering of Automobile Parts.

Description : Differentiate Hardening and Tempering of Automobile Parts.

Last Answer : Differentiate Hardening and Tempering: Parameter Hardening Tempering Definition Hardening or quenching is the process of increasing the hardness of a material. Tempering is the process of ... a metal tempering is done to reduce the brittleness of quenched metal or alloy.

Write four properties of Ceramic Materials and give it’s applications in automobile industry.

Description : Write four properties of Ceramic Materials and give it’s applications in automobile industry.

Last Answer : Properties of Ceramic Material: i. Inorganic & non -metallic material. ii. Brittle material. iii. Insulation to flow of electric current iv. Withstand high temperature. v. Rock like appearance vi. Hardness ... mica etc. 7. In I.C. engines and turbines as armor plates. 8. In cutting tools 

Classify various types of molding sands and give it’s uses.

Description : Classify various types of molding sands and give it’s uses.

Last Answer : 1. Special Sand: Uses: Used for cores of brass and bronze casting, for non- ferrous castings of an intricate shape and for heavy steel casting.  2. Green sand: Uses: It is used only for simple and ... 9. Core sand: Uses: Sand used for making cores is called core sand, sometimes called, oil sand. 

Describe Carburizing Process with its applications.

Description : Describe Carburizing Process with its applications.

Last Answer : Principle of Carburizing: Carburizing is the case hardening process to obtain hard wear resistant and shock resistant case /surface and tough core inside, by introducing carbon on the steel surface by ... temperature.  Applications of Carburizing: 1) Gears 2) Camshafts 3) Bearings 4) Shafts