The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance. (A) Casting (B) Pattern (C) Draft (D) Distortion

The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
(A) Casting
(B) Pattern
(C) Draft
(D) Distortion
by

1 Answer

Answer :

C) Draft
by

Related questions

Use suitable pattern allowance to compensate the shrinkage problem during casting process.

Description : Use suitable pattern allowance to compensate the shrinkage problem during casting process.

Last Answer : Shrinkage Allowance: As metal solidifies and cools, it shrinks and contracts in size. To compensate for this, a pattern is made larger than the finished casting by means of a shrinkage or ... are reduced by gates & risers Solid contraction can be reduced by providing more allowance on pattern 

Shrinkage allowance on pattern is provided to compensate for shrinkage when the (A) Metal changes from liquid state to solid state at freezing temperature (B) Solid phase temperature drops from freezing temperature to the room temperature (C) Liquid metal temperature drops from pouring temperature to room temperature (D) Liquid metal temperature drops from pouring temperature to freezing temperature

Description : Shrinkage allowance on pattern is provided to compensate for shrinkage when the (A) Metal changes from liquid state to solid state at freezing temperature (B) Solid phase temperature drops ... to room temperature (D) Liquid metal temperature drops from pouring temperature to freezing temperature

Last Answer : (B) Solid phase temperature drops from freezing temperature to the room temperature

Uniform ramming of sand in green sand moulding process leads to (A) Reduced chance of gas porosity (B) Greater dimensional stability of the casting (C) Uniform flow of molten metal into the mould cavity (D) Less sand expansion type of casting defect

Description : Uniform ramming of sand in green sand moulding process leads to (A) Reduced chance of gas porosity (B) Greater dimensional stability of the casting (C) Uniform flow of molten metal into the mould cavity (D) Less sand expansion type of casting defect

Last Answer : Option B

Withdrawal for claim for travelling allowance of government Servants may be allowed even without Surrender of LPC The above said stamen is a. True b. False

Description : Withdrawal for claim for travelling allowance of government Servants may be allowed even without Surrender of LPC The above said stamen is a. True b. False

Last Answer : a. True

In die casting, machining allowance is

Description : In die casting, machining allowance is 1. Small 2. Large 3. Very large 4. Not provided

Last Answer : In die casting, machining allowance is Not provided

A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Description : A partial denture that seats on the master cast but fails to seat correctly in the mouth is a result of, A. Contraction of the metal framework during casting B. Insufficient expansion of the investment material C. Distortion of impression D. Failure to block out unwanted undercuts

Last Answer : C. Distortion of impression

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Description : Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Last Answer : c) Take low radial and heavy loads

Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand. (A) Parting (B) Synthetic (C) Loam (D) Dry

Description : Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand. (A) Parting (B) Synthetic (C) Loam (D) Dry

Last Answer : (A) Parting

Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Description : Induced draft fans provided in large thermal power plant boilers have __________ blades. (A) Forward curved (B) Backward curved (C) Double curved (D) Radial or straight

Last Answer : (B) Backward curved

The tillage pattern are a) Head land pattern b) Gathering c) Casting d) All of these Ans. d

Description : The tillage pattern are a) Head land pattern b) Gathering c) Casting d) All of these Ans. d

Last Answer : ans d

Why would you invest the wax pattern as soon as possible in an indirect inlay fabrication: A. Minimise distortion B. Avoid contraction C. Avoid expansion

Description : Why would you invest the wax pattern as soon as possible in an indirect inlay fabrication: A. Minimise distortion B. Avoid contraction C. Avoid expansion

Last Answer : A. Minimise distortion

Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The internal surface of the mould is kept clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Description : Pick up the incorrect statement from the following: (A) The bottom and top ends of slump mould are parallel to each other (B) The axis of the mould is perpendicular to the end faces (C) The ... clean and free from set cement (D) The mould is in the form of a frustum of hexagonal pyramid

Last Answer : Answer: Option D

Mark the correct statement. a) Second withdrawal in a PPF account is payable in the next financial year of the year in which principal and interest on first withdrawal has been fully refunded and other conditions fulfill b) Second loan is permissible in the financial year in which 1st loan and interest thereon has been recovered provided the 1st loan was not taken in the same year and other conditions fulfill c) Second loan is permissible in the same financial year if first loan taken in the year has been refunded alongwith interest thereon and other conditions fulfill d) None of the above is correct

Description : Mark the correct statement. a) Second withdrawal in a PPF account is payable in the next financial year of the year in which principal and interest on first withdrawal has been fully ... been refunded alongwith interest thereon and other conditions fulfill d) None of the above is correct

Last Answer : b) Second loan is permissible in the financial year in which 1st loan and interest thereon has been recovered provided the 1st loan was not taken in the same year and other conditions fulfill

Notched disc blades on disc harrows are provided to a) Enhance penetration b) Improve balancing of gangs c) Save on steel d) Reduce draft

Description : Notched disc blades on disc harrows are provided to a) Enhance penetration b) Improve balancing of gangs c) Save on steel d) Reduce draft

Last Answer : ans a

Cast iron and steel pipes are produced by __________ casting. (A) Die (B) Investment (C) Slush(D) True centrifugal

Description : Cast iron and steel pipes are produced by __________ casting. (A) Die (B) Investment (C) Slush (D) True centrifugal

Last Answer : (D) True centrifugal

Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Description : Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses. (A) Forging (B) Cold rolling (C) Hot rolling (D) Casting

Last Answer : (B) Cold rolling

Very high sulphur in pig iron makes (A) Its casting unsound (B) Its hard and machinable (C) Its brittle and malleable (D) All (A), (B) & (C)

Description : Very high sulphur in pig iron makes (A) Its casting unsound (B) Its hard and machinable (C) Its brittle and malleable (D) All (A), (B) & (C)

Last Answer : (A) Its casting unsound

Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting) (A) V/A (B) V/A2 (C) V2/A (D) V2/A2

Description : Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting) (A) V/A (B) V/A2 (C) V2/A (D) V2/A2

Last Answer : (D) V2/A2

When IBM ships products to its subsidiary in Argentina, it will most likely use a ____ draft. A. sight B. clean C. D/P D. demand E. all of the above

Description : When IBM ships products to its subsidiary in Argentina, it will most likely use a ____ draft. A. sight B. clean C. D/P D. demand E. all of the above

Last Answer : B. clean

Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Description : Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Last Answer : options A

Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Description : Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Last Answer : Option C

Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Description : Oxygen cylinders used for autogenous (cutting/welding) purposes are (A) Seamless & made of steel (B) Heat treated before use (C) Made by sand casting (D) Welded steel cylinders

Last Answer : Option A

Preheating before welding is done to (A) Make the plate softer (B) Burn oil & grease sticking to plate surfaces (C) Avoid plate distortion (D) Prevent cold cracks

Description : Preheating before welding is done to (A) Make the plate softer (B) Burn oil & grease sticking to plate surfaces (C) Avoid plate distortion (D) Prevent cold cracks

Last Answer : (D) Prevent cold cracks

Vapor phase reaction of ammonia & nitric acid to produce ammonium nitrate is termed as the __________ process. (A) Haber's (B) Stengel (C) Le-chatelier's (D) Du-pont's

Description : Vapor phase reaction of ammonia & nitric acid to produce ammonium nitrate is termed as the __________ process. (A) Haber's (B) Stengel (C) Le-chatelier's (D) Du-pont's

Last Answer : (B) Stengel

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel. (A) Wrought (B) Tool (C) Alloy (D) Plain carbon

Description : Steel containing low percentage of nickel, chromium & tungsten are termed as the __________ steel. (A) Wrought (B) Tool (C) Alloy (D) Plain carbon

Last Answer : (D) Plain carbon

A __________ is a gift to a retailer who purchases a specified quantity of merchandise. A)dealer loader B)premium C)dealer listing D)merchandise allowance E)count and recount

Description : A __________ is a gift to a retailer who purchases a specified quantity of merchandise. A)dealer loader B)premium C)dealer listing D)merchandise allowance E)count and recount

Last Answer : A)dealer loader

New Small Scale industries are exempted from the payment of income tax under section 80J is called __________ A. Development Rebate.. B. Investment Allowance. C. Rehabilitation Allowance. D. Tax Holiday

Description : New Small Scale industries are exempted from the payment of income tax under section 80J is called __________ A. Development Rebate.. B. Investment Allowance. C. Rehabilitation Allowance. D. Tax Holiday

Last Answer : B. Investment Allowance.

How do I gauge my ears to a 00g using a size 0g taper?

Description : How do I gauge my ears to a 00g using a size 0g taper?

Last Answer : Take your tape and roll it up – convert size og to cm- then make your roll to that

What chemical changes happen when wax taper is used to light a firework?

Description : What chemical changes happen when wax taper is used to light a firework?

Last Answer : Feel Free to Answer

What is a cylinder taper?

Description : What is a cylinder taper?

Last Answer : What is the answer ?

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Description : In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Last Answer : (d) 25°

Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Description : Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Last Answer : (c) Needle roller bearing

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Description : Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Last Answer : c) Both axial and thrust loads

The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Description : The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Last Answer : b) disagree

Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Description : Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Last Answer : D. 1 in 48 to 1 in 24

Taper is made cotter and slot on both the side. A. Yes B. No

Description : Taper is made cotter and slot on both the side. A. Yes B. No

Last Answer : B. No

Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Description : Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Last Answer : A. Top side only

Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Description : Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Last Answer : C. 1 in 100

A single lane carriage way whenever changes to two-lane carriage way, is affected through a taper of (A) 1 in 10 (B) 1 in 15 (C) 1 in 20 (D) 1 in 15 to 1 in 20

Description : A single lane carriage way whenever changes to two-lane carriage way, is affected through a taper of (A) 1 in 10 (B) 1 in 15 (C) 1 in 20 (D) 1 in 15 to 1 in 20

Last Answer : Answer: Option D

The taper of precast concrete pile should not be more than (A) 1 cm per metre length (B) 2 cm per metre length (C) 4 cm per metre length (D) 5 cm per metre length

Description : The taper of precast concrete pile should not be more than (A) 1 cm per metre length (B) 2 cm per metre length (C) 4 cm per metre length (D) 5 cm per metre length

Last Answer : Answer: Option B

What Is The Use Of Taper Roller Bearing?

Description : What Is The Use Of Taper Roller Bearing?

Last Answer : A taper roller bearing is used to carry heavy loads because it has taper rollers instead of plain cylindrical rollers.