Description : Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon ... the metal surface) cause nitride formation with increase in surface hardness (D) None of these
Last Answer : (D) None of these
Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these
Description : Presence of even 0.005% of __________ in copper makes it highly brittle, rendering it useless for wire-drawing. (A) Oxygen (B) Arsenic (C) Antimony (D) Bismuth
Last Answer : (D) Bismuth
Description : The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'
Last Answer : (A) Carbon
Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile
Last Answer : (A) Impact
Description : Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity
Last Answer : (C) Tenacity & hardness
Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these
Last Answer : (B) Tensile strength
Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'
Last Answer : (A) Impact strength
Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content
Last Answer : (D) Alloying elements content Sh
Description : Pick out the wrong statement (A) Hardening makes the steel more brittle (B) High alloy steels contain more than 50% alloying element (C) 18/8 stainless steel is a magnetic steel (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'
Last Answer : (A) Percentage elongation
Description : Smith's test of stones is performed to find out (A) The presence of soluble matter of stone (B) The compressive strength of the stone (C) The hardness of the stone (D) The toughness of the stone
Last Answer : Answer: Option A
Description : All of the following alloying elements of steel increases hardness but sacrifice ductility, except (A) Nickel (B) Vanadium (C) Molybdenum (D) Chromium
Last Answer : (A) Nickel
Description : A Plain Carbon Steel Has Brinell Hardness Number (bhn) Of 180. What Are The Values Of Rc, Vhn And Ultimate Strength?
Last Answer : Rc = BHN/10 = 18, VHN = BHN = 180 Ultimate strength = 3.48 × BHN MPa = 620 MPa.
Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength
Last Answer : (A) Cutting ability
Description : Presence of predominantly large quantity of aromatics (polynuclear) is not desirable in aviation fuel, because it has (A) High pour point and low smoke point (B) Low viscosity index (C) High self-ignition temperature (D) All (A), (B) and (C)
Last Answer : (B) Low viscosity index
Description : Priming in a distillation column (A) Results from very low gas velocity (B) Is desirable from point efficiency consideration (C) Is characterised by the presence of foam throughout the space between trays (D) Reduces the overall pressure drop
Last Answer : (C) Is characterised by the presence of foam throughout the space between trays
Description : Presence of a certain minimum quantity of fluorine is desirable in potable water to prevent (A) Dental cavities (B) Scale formation (C) Water-borne disease (D) Corrosion
Last Answer : (A) Dental cavities
Description : Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength
Last Answer : (A) Fluidity
Description : High ash containing coke (A) Produces more slag when used in the blast furnace (B) Has poor strength and abrasion resistance (C) Is desirable in producer gas manufacture (D) None of these
Last Answer : (A) Produces more slag when used in the blast furnace
Description : Tempering of steel is done to make it (A) Brittle (B) Hard (C) Rollable (D) Soft
Last Answer : (D) Soft
Description : Steel produced from phosphatic iron is __________ in nature. (A) Malleable (B) Ductile (C) Brittle (D) Tough
Last Answer : (C) Brittle
Description : . Presence of iron and manganese in water causes (A) Reduction in its dissolved oxygen content (B) Discoloration of bathroom fixtures (C) Temporary hardness (D) None of these
Last Answer : (B) Discoloration of bathroom fixtures
Description : Presence of H2S in raw water (to be chlorinated) results in the (A) Reduced softening capacity of zeolite (B) Increased dosage of chlorine to provide a disinfecting residual in the water (C) Easy removal of its hardness (D) None of these
Last Answer : (B) Increased dosage of chlorine to provide a disinfecting residual in the water
Description : Pick out the wrong statement. (A) Fibrillation of fibre during paper manufacture is done to develop the strength in paper (B) Alkali consumption in digestion/cooking of bamboo is measured in terms ... both lignin & cellulose (D) Presence of sodium sulphate in pulp makes the pulp bleachability poor
Last Answer : (D) Presence of sodium sulphate in pulp makes the pulp bleachability poor
Description : Presence of __________ hardness is responsible for the temporary hardness in water. (A) Carbonate (B) Calcium (C) Chloride (D) Sulphate
Last Answer : (B) Calcium
Description : Very high sulphur in pig iron makes (A) Its casting unsound (B) Its hard and machinable (C) Its brittle and malleable (D) All (A), (B) & (C)
Last Answer : (A) Its casting unsound
Description : Building strength into brittle hair?
Last Answer : vitamins high in amino acids
Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (c) Thirdly Ultimate=yield=elastic limit
Description : Asbestos cement (A) Is brittle (B) Warps due to changes in humidity (C) Strength is lowered when saturated by water (D) All of the above
Last Answer : Answer: Option D
Description : Back-trapping in a distillation column (A) Increases tray efficiency (B) Decreases tray efficiency (C) Reduces pressure drop (D) Is desirable, as it provides improved vapour-liquid contact
Last Answer : (B) Decreases tray efficiency
Description : The addition of antimony in tin-based alloys improves its (A) Rupture strength and hot hardness (B) Impact strength and bonding strength (C) Deformation resistance (D) Wear resistance
Last Answer : (C) Deformation resistance
Description : Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness
Last Answer : (D) Hardness
Description : Wrought iron is having very high (A) Hardness (B) Strength (C) Corrosion resistance (D) Susceptibility to changes in its properties by heat treatment
Last Answer : (C) Corrosion resistance
Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected
Last Answer : (C) Appreciable strain hardening is produced
Description : Critical Air Blast (CAB) value of coke is a direct measure of its (A) Reactivity (B) Hardness (C) Strength (D) None of these
Last Answer : (A) Reactivity
Description : A good metallurgical coke should have very low (A) Sulphur & phosphorous content (B) Porosity (C) Fusion point of its ash (D) Hardness & strength
Last Answer : (A) Sulphur & phosphorous content
Description : "Micum Index" of a coke is a measure of its (A) Reactivity (B) Porosity (C) Bulk density (D) Hardness & strength
Last Answer : (D) Hardness & strength
Description : M10 index of coke indicates its (A) Compressive strength (B) Hardness (C) Abrasion resistance (D) Impact strength
Last Answer : Option C
Description : M10 index of coke indicates its (A) Compressive strength (B) Hardness (C) Abrasion resistance (D) Impact strength Answer: Option C
Description : The presence of impurities in iron (A) Increases its melting point (B) Does not affect its melting point (C) Decreases its melting point (D) Makes it malleable
Last Answer : (C) Decreases its melting point
Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness
Last Answer : (D) Hardness, rigidity & brittleness
Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process
Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance
Last Answer : (B) Toughness
Description : Is it desirable to use concrete of very high strength i.e. exceeding 60MPa? What are the potential problems associated with such high strength concrete?
Last Answer : To increase the strength of concrete, say from 40MPa to 80MPa, it definitely helps in improving the structural performance of the structure by producing a denser, more durable and higher load ... Moreover, owing to a low aggregate content of high strength concrete, creep and shrinkage increases.
Description : Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability
Last Answer : C) high thermal conductivity
Description : 'Shock-absorbers are usually made of steel as it – (1) is not brittle (2) has lower elasticity (3) has higher elasticity (4) has no ductile property
Last Answer : (3) has higher elasticity Explanation: A shock absorber is a mechanical device designed to smooth out or damp shock impulse, and dissipate kinetic energy. Steel is an alloy made by combining iron and other elements, the most common of these being carbon.