. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

. In a linear polymer, the monomeric units are linked together to form
long straight chains. The cross linked or branched chain polymers
compared to linear polymers have higher
(A) Densities
(B) Melting point
(C) Tensile strength
(D) Hardness, rigidity & brittleness
by

1 Answer

Answer :

(D) Hardness, rigidity & brittleness
by

Related questions

Branched chain polymers compared to linear polymers have higher (A) Density (B) Tensile strength (C) Melting point (D) Degree of irregularity in atomic packing

Description : Branched chain polymers compared to linear polymers have higher (A) Density (B) Tensile strength (C) Melting point (D) Degree of irregularity in atomic packing

Last Answer : (D) Degree of irregularity in atomic packing

Branched chair polymers as compared to linear polymers have (A) Higher melting point (B) Higher tensile strength (C) Lower density (D) None of these

Description : Branched chair polymers as compared to linear polymers have (A) Higher melting point (B) Higher tensile strength (C) Lower density (D) None of these

Last Answer : (C) Lower density

Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Description : Cross linked polymers formed from bi-and trifunctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties. (A) Thermoplastic (B) Thermosetting (C) Elastometric (D) Brittleness

Last Answer : (C) Elastometric

Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or thermosetting (C) Branching in case of cross-linked polymers caused by small amount of impurities in bifunctional monomer formulation reduces its solubility and increases the softening point (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Description : Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or ... (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Last Answer : D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross￾linked polymer? (A) Bakelite (phenol formaldehyde) (B) Polyester (C) Polythene (D) Nylon-6

Description : In a cross linked polymer, the monomeric units are linked together to constitute a three dimensional network. Which of the following is a cross￾linked polymer? (A) Bakelite (phenol formaldehyde) (B) Polyester (C) Polythene (D) Nylon-6

Last Answer : (A) Bakelite (phenol formaldehyde)

What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Description : What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Last Answer : amount of hydrogen bonding between different subunitsnumber of subunits in the polymer chainits greater tensile strengththe synthetic composure

The monomeric units that make up peptides and protein polymers are __________. (a) nucleic acids (b) amino acids (c) oligosaccharides (d) amylopectins

Description : The monomeric units that make up peptides and protein polymers are __________. (a) nucleic acids (b) amino acids (c) oligosaccharides (d) amylopectins

Last Answer : amylopectins

Cellulose, the most important constituent of plant cell wall is made up of (a) branched chain of glucose molecules linked by β-1, 4 glycosidic bond in straight chain and α-1, 6 glycosidic bond at the site of branching (b) unbranched chain of glucose molecules linked by β-1, 4 glycosidic bond (c) branched chain of glucose molecules linked by α-1, 6 glycosidic bond at the site of branching (d) unbranched chain of glucose molecules linked by α-1, 4 glycosidic bond.

Description : Cellulose, the most important constituent of plant cell wall is made up of (a) branched chain of glucose molecules linked by β-1, 4 glycosidic bond in straight chain and α-1, 6 glycosidic bond ... the site of branching (d) unbranched chain of glucose molecules linked by α-1, 4 glycosidic bond.

Last Answer : (b) unbranched chain of glucose molecules linked by β-1, 4 glycosidic bond

Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Last Answer : Option B

Choose the correct statement. (A) Octane number of i-octane is zero (B) Octane number of paraffins increases with increasing number of carbon atoms (C) Branched chain paraffins have higher octane number than straight chain paraffins with same number of carbon atoms (D) The aromatics have lower octane number than naphthenes with same number of carbon atoms

Description : Choose the correct statement. (A) Octane number of i-octane is zero (B) Octane number of paraffins increases with increasing number of carbon atoms (C) Branched chain paraffins have higher octane ... atoms (D) The aromatics have lower octane number than naphthenes with same number of carbon atoms

Last Answer : (A) Octane number of i-octane is zero

Which of the following statements best describes the difference between amylose and amylopectin? (a) Amylose is a branched polysaccharide while amylopectin is a chain polysaccharide. (b) Amylose is a straight-chain polysaccharide while amylopectin is a branched polysaccharide. (c) Amylose contains α-1,6-glycosidic linkage which amylopectin does not contain. (d) Amylose is composed of thousands of D-glucose units while amylopectin is composed of thousands of D-galactose units.

Description : Which of the following statements best describes the difference between amylose and amylopectin? (a) Amylose is a branched polysaccharide while amylopectin is a chain polysaccharide. (b) Amylose is a ... of thousands of D-glucose units while amylopectin is composed of thousands of D-galactose units.

Last Answer : Amylose is a straight-chain polysaccharide while amylopectin is a branched polysaccharide

Nylon-66 compared to nylon-6 has (A) Lower melting point (B) More abrasion resistant properties (C) Higher hardness (D) All (A), (B) and (C)

Description : Nylon-66 compared to nylon-6 has (A) Lower melting point (B) More abrasion resistant properties (C) Higher hardness (D) All (A), (B) and (C)

Last Answer : (C) Higher hardness

A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Description : A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Last Answer : (A) More corrosion resistant

Nylon-6 as compared to Nylon-66 is having higher (A) Hardness (B) Abrasion/resistance (C) Melting point (D) None of these

Description : Nylon-6 as compared to Nylon-66 is having higher (A) Hardness (B) Abrasion/resistance (C) Melting point (D) None of these

Last Answer : (D) None of these

Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter polymer melt to harden into filaments. Melt spinning is not used in case of the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Description : Melt spinning of polymers involves the forcing of polymer melt through spinnerates (fine holes) into an atmosphere kept at a temperature lower than the melting point of the polymer, which causes the fine diameter ... the __________ fibres. (A) Acrylic (B) Polyester (C) Nylon 6:6 (D) Polypropylene

Last Answer : (A) Acrylic

Higher percentage of ash in coal meant for the production of metallurgical grade coke (A) Decreases the hardness of coke (B) Decreases the abrasion resistance of coke (C) Causes brittleness in steel (D) None of these

Description : Higher percentage of ash in coal meant for the production of metallurgical grade coke (A) Decreases the hardness of coke (B) Decreases the abrasion resistance of coke (C) Causes brittleness in steel (D) None of these

Last Answer : (D) None of these

Neoprene is rendered non-inflammable, because of (A) Its cross-linked structure (B) Its linear chain structure (C) The presence of chlorine atoms in its monomer (D) The absence of chlorine atoms in its monomer

Description : Neoprene is rendered non-inflammable, because of (A) Its cross-linked structure (B) Its linear chain structure (C) The presence of chlorine atoms in its monomer (D) The absence of chlorine atoms in its monomer

Last Answer : (C) The presence of chlorine atoms in its monomer

Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Description : Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Last Answer : (C) Flexibility

Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Description : Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Last Answer : (B) Softness & flexibility

Ceramic compounds as compared to metallic compounds (A) Crystallise faster (B) Resist greater tensile stress at room temperature (C) Have higher melting temperature (D) Are better conductor of electricity at higher temperature

Description : Ceramic compounds as compared to metallic compounds (A) Crystallise faster (B) Resist greater tensile stress at room temperature (C) Have higher melting temperature (D) Are better conductor of electricity at higher temperature

Last Answer : Option C

Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Description : Polymerisation of poly functional monomers produces polymers having (A) Good mechanical strength (B) Low viscosity (C) Low melting point (D) None of these

Last Answer : (A) Good mechanical strength

Which of the following is/are true? A. Because of its thickness, the tensile strength of a healing wound on the eyelid is much less than one on the thick skin of the back. B. By 2 days, the experimental burst strength of skin is minimal since collagen has been formed in the wound but has not yet cross-linked. C. Wound strength reaches a plateau by 3 weeks. D. Wounds rarely, if ever, regain the strength of intact tissues.

Description : Which of the following is/are true? A. Because of its thickness, the tensile strength of a healing wound on the eyelid is much less than one on the thick skin of the back. B. By 2 days, ... strength reaches a plateau by 3 weeks. D. Wounds rarely, if ever, regain the strength of intact tissues.

Last Answer : Answer: BD DISCUSSION: Tensile strength measures load per cross-section area at rupture, whereas burst strength measures load required to break a wound, regardless of dimension. Therefore, skin wounds have ... a slower rate for more than a year. Wounds do not regain the strength of normal tissue

With increase in carbide/graphite ratio in cast iron, its (A) Hardness & brittleness increases (B) Ductility decreases (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : With increase in carbide/graphite ratio in cast iron, its (A) Hardness & brittleness increases (B) Ductility decreases (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Last Answer : (D) Alloying elements content Sh

Pick out the correct combination about the role of various additives used in polymers. (A) Plasticiser: increases the polymer strength (B) Heat stabiliser: increases the maximum service temperature (C) Fillers: Does not affect the property of polymer but increases its weight (D) Lubricants: increases the flexibility of polymers

Description : Pick out the correct combination about the role of various additives used in polymers. (A) Plasticiser: increases the polymer strength (B) Heat stabiliser: increases the maximum service ... property of polymer but increases its weight (D) Lubricants: increases the flexibility of polymers

Last Answer : Option C

Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more aliphatic character are more soluble in aliphatic solvents, while those polymers having more aromatic character are more soluble in aromatic solvents (C) Swelling tendency or solubility of polymers in a particular solvent decreases with increase in molecular weight of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Description : Pick out the wrong statement regarding the solubility characteristics of high polymers. (A) Greater the degree of cross-linking in the polymer, lesser is its solubility (B) Polymers having more ... of the solvent (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Last Answer : (D) High molecular weight polymers on dissolving gives solution of very low viscosity

Cross linked polymers are (A) Thermoplastic (B) Thermosetting (C) Either (A) or (B) (D) Fibres only

Description : Cross linked polymers are (A) Thermoplastic (B) Thermosetting (C) Either (A) or (B) (D) Fibres only

Last Answer : (B) Thermosetting

Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Description : Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Last Answer : (A) Higher melting points

Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Description : Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Last Answer : (A) Fluidity

Unsaturated oils compared to saturated oils have (A) Lower melting point & higher reactivity to oxygen (B) Higher melting point & higher reactivity to oxygen (C) Lower melting point & lower reactivity to oxygen (D) Higher melting point & lower reactivity to oxygen

Description : Unsaturated oils compared to saturated oils have (A) Lower melting point & higher reactivity to oxygen (B) Higher melting point & higher reactivity to oxygen (C) Lower melting point & lower reactivity to oxygen (D) Higher melting point & lower reactivity to oxygen

Last Answer : (A) Lower melting point & higher reactivity to oxygen

Thermosetting polymers as compared to thermoplastic polymers (A) Are formed by addition polymerisation (B) Have three dimensional structure (C) Have linear structure (D) None of these

Description : Thermosetting polymers as compared to thermoplastic polymers (A) Are formed by addition polymerisation (B) Have three dimensional structure (C) Have linear structure (D) None of these

Last Answer : (B) Have three dimensional structure

. Polymers which soften on heating and harden when cooled are (a) Cross-linked polymers (b) Copolymers (c) Thermosetting polymers (d) Thermoplastics

Description : Polymers which soften on heating and harden when cooled are (a) Cross-linked polymers (b) Copolymers (c) Thermosetting polymers (d) Thermoplastics

Last Answer : Thermoplastics

The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Last Answer : (C) Hardness

Increasing the carbon content of steel (A) Reduces the upper shelf energy (B) Increasing the ductility transition temperature (C) Decreases brittleness (D) Decreases hardness

Description : Increasing the carbon content of steel (A) Reduces the upper shelf energy (B) Increasing the ductility transition temperature (C) Decreases brittleness (D) Decreases hardness

Last Answer : (B) Increasing the ductility transition temperature

The following are true about the sodium channels: a. they are made up of polypeptide chains b. have the highest densities at the nodes of Ranvier c. open in response to depolarization d. remain open as long as depolarization is maintained

Description : The following are true about the sodium channels: a. they are made up of polypeptide chains b. have the highest densities at the nodes of Ranvier c. open in response to depolarization d. remain open as long as depolarization is maintained

Last Answer : have the highest densities at the nodes of Ranvier

Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Last Answer : (B) Tensile strength

Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Last Answer : (B) Toughness

Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Last Answer : (B) Tensile strength

With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What is the purpose of plasticizers? (a) Harden plastics (b) Soften plastics (c) Initiate polymerizations (d) Cross-link polymer chains

Description : What is the purpose of plasticizers? (a) Harden plastics (b) Soften plastics (c) Initiate polymerizations (d) Cross-link polymer chains

Last Answer : Soften plastics

Vulcanization is the process of cross-linking polymer chains in rubber using (a) Sulfur. (b) Formaldehye. (c) Benzoyl peroxide. (d) Ethylene glycol.

Description : Vulcanization is the process of cross-linking polymer chains in rubber using (a) Sulfur. (b) Formaldehye. (c) Benzoyl peroxide. (d) Ethylene glycol.

Last Answer : Sulfur.

Which of the following statements is not correct? (a) In man insulin is synthesised as a proinsulin. (b) The proinsulin has an extra peptide called C-peptide. (c) The functional insulin has A and B chains linked together by hydrogen bonds. (d) Genetically engineered insulin is produced in E.Coli.

Description : Which of the following statements is not correct? (a) In man insulin is synthesised as a proinsulin. (b) The proinsulin has an extra peptide called C-peptide. (c) The functional insulin has A and B chains linked together by hydrogen bonds. (d) Genetically engineered insulin is produced in E.Coli.

Last Answer : (c) The functional insulin has A and B chains linked together by hydrogen bonds.

Covalent network crystals have-------? A. higher melting point then molecular crystals (Answer) B. lower melting point then molecular crystals C. discrete molecules linked by Van der waals forces D. hydrogen bonding

Description : Covalent network crystals have-------? A. higher melting point then molecular crystals (Answer) B. lower melting point then molecular crystals C. discrete molecules linked by Van der waals forces D. hydrogen bonding

Last Answer : A. higher melting point then molecular crystals (Answer)

Heavy metals got their name because compared to other atoms they have - (1) Higher densities (2) Higher atomic masses (3) Higher atomic numbers (4) Higher atomic radii

Description : Heavy metals got their name because compared to other atoms they have - (1) Higher densities (2) Higher atomic masses (3) Higher atomic numbers (4) Higher atomic radii

Last Answer : (2) Higher atomic masses Explanation: Arsenic, beryllium, cadmium, chromium, lead, manganese, mercury, nickel, and selenium are some of the metals called 'heavy' because of their high relative atomic ... and can cause damage or death in animals, humans, and plants even at very low concentrations.

Heavy metals got their name because compared to other atoms they have (1) Higher densities (2) Higher atomic masses (3) Higher atomic numbers (4) Higher atomic radii

Description : Heavy metals got their name because compared to other atoms they have (1) Higher densities (2) Higher atomic masses (3) Higher atomic numbers (4) Higher atomic radii

Last Answer : Higher atomic masses

Electrostatic separation of minerals from each other is based on their differences in the following property. (A) Densities (B) Magnetic permeabilities (C) Electrical conductivities (D) Hardness

Description : Electrostatic separation of minerals from each other is based on their differences in the following property. (A) Densities (B) Magnetic permeabilities (C) Electrical conductivities (D) Hardness

Last Answer : (C) Electrical conductivities

In nylon-6, the number 6 represents the total number of (A) Carbon atoms in the ring (B) Carbon atoms in the linear polymer chain (C) Nitrogen atoms in the ring (D) Hydrogen atoms in the ring

Description : In nylon-6, the number 6 represents the total number of (A) Carbon atoms in the ring (B) Carbon atoms in the linear polymer chain (C) Nitrogen atoms in the ring (D) Hydrogen atoms in the ring

Last Answer : (B) Carbon atoms in the linear polymer chain