Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Cast irons are generally specified by their
(A) Carbon content
(B) Tensile strength
(C) Hardness
(D) Manufacturing process
by

1 Answer

Answer :

(B) Tensile strength
by

Related questions

Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Last Answer : (D) Alloying elements content Sh

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

The graphite in grey irons exists in the form of flakes which act as stress-raisers under tensile loading and consequently grey irons have relatively low tensile strength and ductility. Still grey iron is extensively used in engineering. Why ?

Description : The graphite in grey irons exists in the form of flakes which act as stress-raisers under tensile loading and consequently grey irons have relatively low tensile strength and ductility. Still grey iron is extensively used in engineering. Why ?

Last Answer : (a) Cheapness. (B) Low melting point and high fluidity making it suitable for castings of intricate shape. (c) Relatively good erosion and corrosion resistance. (d) High damping capacity, with respect to vibration. (e) Relatively good mechanical properties under compressive loading.

With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Last Answer : (C) Cast iron

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Last Answer : Option B

. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Last Answer : (D) Hardness, rigidity & brittleness

Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Last Answer : (B) Toughness

Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Last Answer : (B) Tensile strength

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Description : Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Last Answer : (B) Resistivity

Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Description : Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Last Answer : i)Tensile Strength : Tensile Strength is the ability of metal to carry a load without breaking. ii)Hardness :- Hardness is the ability of metal to resist wear or abrasion and resist penetration. ... a non ferrous alloy having melting point below 4000 c in between them is called as soldering. 

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Description : Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Last Answer : (A) Fluidity

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength

Which one has the maximum tensile strength out of the following? (A) Nodular cast iron (B) Pig iron (C) White cast iron (D) Grey cast iron

Description : Which one has the maximum tensile strength out of the following? (A) Nodular cast iron (B) Pig iron (C) White cast iron (D) Grey cast iron

Last Answer : (A) Nodular cast iron

Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Description : Cast iron is having very high (A) Proximity between its elastic limit and ultimate breaking strength (B) Ductility (C) Tensile strength (D) All (A), (B) and (C)

Last Answer : (A) Proximity between its elastic limit and ultimate breaking strength

Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength(D) All (A), (B) & (C)

Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

High carbon content in the steel causes (A) Decrease in tensile strength but increase in ductility (B) Increase in tensile strength but decrease in ductility (C) Decrease in both tensile strength and ductility (D) Increase in both tensile strength and ductility

Description : High carbon content in the steel causes (A) Decrease in tensile strength but increase in ductility (B) Increase in tensile strength but decrease in ductility (C) Decrease in both tensile strength and ductility (D) Increase in both tensile strength and ductility

Last Answer : Answer: Option B

Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Last Answer : (D) All of the above

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Last Answer : d. Good cast ability

Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Last Answer : (B) Sharp melting points

A good metallurgical coke should have very low (A) Sulphur & phosphorous content (B) Porosity (C) Fusion point of its ash (D) Hardness & strength

Description : A good metallurgical coke should have very low (A) Sulphur & phosphorous content (B) Porosity (C) Fusion point of its ash (D) Hardness & strength

Last Answer : (A) Sulphur & phosphorous content

Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel. (A) 0.01 to 0.10 (B) 0.2 to 0.4 (C) 0.5 to 0.7 (D) 0.8 to 1.0

Description : Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel. (A) 0.01 to 0.10 (B) 0.2 to 0.4 (C) 0.5 to 0.7 (D) 0.8 to 1.0

Last Answer : (B) 0.2 to 0.4

Increasing the carbon content of steel (A) Reduces the upper shelf energy (B) Increasing the ductility transition temperature (C) Decreases brittleness (D) Decreases hardness

Description : Increasing the carbon content of steel (A) Reduces the upper shelf energy (B) Increasing the ductility transition temperature (C) Decreases brittleness (D) Decreases hardness

Last Answer : (B) Increasing the ductility transition temperature

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

_______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Description : _______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Last Answer : (A) Hardness

__________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Last Answer : (A) Impact

Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Last Answer : Option B

What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Description : What is elasticity in polymers generally related to amount of hydrogen bonding between different subunits number of subunits in the polymer chain its greater tensile strength the synthetic composure?

Last Answer : amount of hydrogen bonding between different subunitsnumber of subunits in the polymer chainits greater tensile strengththe synthetic composure

.The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Description : .The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Last Answer : B. Less corrosion

A Plain Carbon Steel Has Brinell Hardness Number (bhn) Of 180. What Are The Values Of Rc, Vhn And Ultimate Strength?

Description : A Plain Carbon Steel Has Brinell Hardness Number (bhn) Of 180. What Are The Values Of Rc, Vhn And Ultimate Strength?

Last Answer : Rc = BHN/10 = 18, VHN = BHN = 180 Ultimate strength = 3.48 × BHN MPa = 620 MPa.

Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Description : Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel

Last Answer : (D) High carbon steel

Annealing of cast iron (A) Softens it to facilitate machining (B) Decreases the free carbon (C) Increases the strength (D) None of these

Description : Annealing of cast iron (A) Softens it to facilitate machining (B) Decreases the free carbon (C) Increases the strength (D) None of these

Last Answer : Option A

With increase in carbide/graphite ratio in cast iron, its (A) Hardness & brittleness increases (B) Ductility decreases (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : With increase in carbide/graphite ratio in cast iron, its (A) Hardness & brittleness increases (B) Ductility decreases (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The most distinguished property of malleable cast iron is its high (A) Ductility (B) Hardness (C) Malleability (D) None of these

Description : The most distinguished property of malleable cast iron is its high (A) Ductility (B) Hardness (C) Malleability (D) None of these

Last Answer : (A) Ductility

Flywheel are generally made from (A) Cast Iron (B) High strength steel (C) Ceramics (D) All of the above

Description : Flywheel are generally made from (A) Cast Iron (B) High strength steel (C) Ceramics (D) All of the above

Last Answer : (D) All of the above

Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Description : Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Last Answer : (B) Chrome carbon steel

Steel balls for ball bearings are generally made of __________ steel. (A) Cast (B) Stainless (C) Free carbon (D) Carbon chrome

Description : Steel balls for ball bearings are generally made of __________ steel. (A) Cast (B) Stainless (C) Free carbon (D) Carbon chrome

Last Answer : (D) Carbon chrome

Galvanising is generally done on (A) Non-ferrous metals (B) Low carbon steel (C) Stainless steel (D) Cast iron

Description : Galvanising is generally done on (A) Non-ferrous metals (B) Low carbon steel (C) Stainless steel (D) Cast iron

Last Answer : (B) Low carbon steel

Maximum carbon content in cast iron is __________ percent. (A) 3.8 (B) 5.2 (C) 4.8 (D) 4.3

Description : Maximum carbon content in cast iron is __________ percent. (A) 3.8 (B) 5.2 (C) 4.8 (D) 4.3

Last Answer : (D) 4.3

How does carbon in steel affect the tensile strength?

Description : How does carbon in steel affect the tensile strength?

Last Answer : Need answer

The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Description : The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Last Answer : Answer: Option D

Heating rubber with sulphur for the bet- terment of its properties ike tensile steqasbh: hardness; elasticity etc. is called as?

Description : Heating rubber with sulphur for the bet- terment of its properties ike tensile steqasbh: hardness; elasticity etc. is called as?

Last Answer : Vulcanisation

Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Description : Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Last Answer : a) Root bend

In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Description : In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Last Answer : b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate

Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Description : Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Last Answer : Option C