In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.
(A) Percentage elongation
(B) Brinell hardness
(C) Tensile strength
(D) All 'a', 'b' & 'c'
by

1 Answer

Answer :

(A) Percentage elongation
by

Related questions

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A Plain Carbon Steel Has Brinell Hardness Number (bhn) Of 180. What Are The Values Of Rc, Vhn And Ultimate Strength?

Description : A Plain Carbon Steel Has Brinell Hardness Number (bhn) Of 180. What Are The Values Of Rc, Vhn And Ultimate Strength?

Last Answer : Rc = BHN/10 = 18, VHN = BHN = 180 Ultimate strength = 3.48 × BHN MPa = 620 MPa.

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Description : Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100 -150 (D) 200 - 250

Last Answer : (B) 20-30

Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100-150

Description : Brinell Hardness Number (BHN) for talc is approximately in the range of (A) 1-5 (B) 20-30 (C) 100-150

Last Answer : Option B

The largest consumption of zinc for alloys is in the making of (A) Bearing metal (B) Brasses (C) Brazing solder

Description : The largest consumption of zinc for alloys is in the making of (A) Bearing metal (B) Brasses (C) Brazing solder

Last Answer : (B) Brasses

The emf of a Deniell cell “Zn | Zn2+|| Cu2+| Cu” can be increased by (A) Decreasing the surface area of the electrodes (B) Increasing the concentration of zinc sulphate solution (C) Increasing the surface area of the electrodes (D) Increasing the concentration of copper sulphate solution

Description : The emf of a Deniell cell “Zn | Zn2+|| Cu2+| Cu” can be increased by (A) Decreasing the surface area of the electrodes (B) Increasing the concentration of zinc sulphate solution (C) Increasing the surface area of the electrodes (D) Increasing the concentration of copper sulphate solution

Last Answer : (D) Increasing the concentration of copper sulphate solution

Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Last Answer : (D) Alloying elements content Sh

. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Last Answer : (D) Hardness, rigidity & brittleness

Softness of silver can be converted into hardness by alloying it with small quantity of (A) Copper & nickel (B) Zinc (C) Aluminium (D) Tin

Description : Softness of silver can be converted into hardness by alloying it with small quantity of (A) Copper & nickel (B) Zinc (C) Aluminium (D) Tin

Last Answer : (A) Copper & nickel

What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Description : What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

Last Answer : ANSWER: Y -- YIELD STRENGTH

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Description : Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Last Answer : (a) Ductility

Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively. (A) 70 & 30 (B) 30 & 70 (C) 50 & 50 (D) 90 & 10

Description : Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively. (A) 70 & 30 (B) 30 & 70 (C) 50 & 50 (D) 90 & 10

Last Answer : (A) 70 & 30

Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Last Answer : (B) Tensile strength

Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Last Answer : (B) Tensile strength

Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Last Answer : (B) Toughness

Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Description : Addition of plasticisers to polymers results in partial neutralisation of intermolecular forces of attraction between the macro-molecules thereby increasing its (A) Tensile strength (B) Chemical resistance (C) Flexibility (D) All (A), (B) & (C)

Last Answer : (C) Flexibility

The advantage of firing porcelain in vacuum:** A. Reduces size of air-bubbles incorporated thus decreasing porosity B. Removes water before firing, increasing the hardness of porcelain C. Significantly lowers firing temperature

Description : The advantage of firing porcelain in vacuum:** A. Reduces size of air-bubbles incorporated thus decreasing porosity B. Removes water before firing, increasing the hardness of porcelain C. Significantly lowers firing temperature

Last Answer : A. Reduces size of air-bubbles incorporated thus decreasing porosity

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Description : Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Last Answer : (C) Tenacity & hardness

In water treatment plant, zeolite process is used to remove the __________ of water. (A) Acidity (B) Alkalinity (C) Hardness (D) Iron & zinc

Description : In water treatment plant, zeolite process is used to remove the __________ of water. (A) Acidity (B) Alkalinity (C) Hardness (D) Iron & zinc

Last Answer : (C) Hardness

(A) Percentage elongation (B) Yield strength (C) Ultimate strength (D) Area under stress-strain diagram

Description : (A) Percentage elongation (B) Yield strength (C) Ultimate strength (D) Area under stress-strain diagram

Last Answer : (B) Yield strength

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Description : Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Last Answer : (C) Tensile strength

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Description : Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Last Answer : (B) Resistivity

Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Description : Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Last Answer : i)Tensile Strength : Tensile Strength is the ability of metal to carry a load without breaking. ii)Hardness :- Hardness is the ability of metal to resist wear or abrasion and resist penetration. ... a non ferrous alloy having melting point below 4000 c in between them is called as soldering. 

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Description : Vulcanisation of rubber (A) Decreases its tensile strength (B) Increases its ozone & oxygen reactivity (C) Increases its oil & solvent resistance (D) Converts its plasticity into elasticity

Last Answer : (D) Converts its plasticity into elasticity

Epinephrine increases the concentration of free fatty acids in plasma by increasing (A) Extramitochondrial fatty acid synthesis (B) Mitochondrial fatty acid chain elongation (C) Microsomal fatty acid chain elongation (D) Lipolysis in adipose tissue

Description : Epinephrine increases the concentration of free fatty acids in plasma by increasing (A) Extramitochondrial fatty acid synthesis (B) Mitochondrial fatty acid chain elongation (C) Microsomal fatty acid chain elongation (D) Lipolysis in adipose tissue

Last Answer : Answer : D

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

__________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Last Answer : (A) Impact

Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Description : Temper brittleness of a material can be fairly detected by the __________ test. (A) Fatigue (B) Notched bar impact (C) Tensile (D) Hardness

Last Answer : Option B

Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness

Description : Addition of nickel to copper improves its (A) Machinability (B) Ductility (C) Strength (D) Hardness

Last Answer : (D) Hardness

__________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Description : __________ of SBR is adversely affected, if more quantity of styrene is added to butadiene during its co-polymerisation to produce SBR. (A) Percent elongation (B) Resilience (C) Freezing point (D) Strength

Last Answer : (B) Resilience

polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent. (A) 150 (B) 200 (C) 300 (D) 400

Description : polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent. (A) 150 (B) 200 (C) 300 (D) 400

Last Answer : Option B

Presence of nitrogen in steel (A) Makes it brittle (B) Increases its strength (C) Increases its hardness (D) Is desirable

Description : Presence of nitrogen in steel (A) Makes it brittle (B) Increases its strength (C) Increases its hardness (D) Is desirable

Last Answer : (A) Makes it brittle

Heat transfer co-efficient (h1 ) for liquids increases with (A) Increasing temperature (B) Decreasing temperature (C) Decreasing Reynolds number (D) None of these

Description : Heat transfer co-efficient (h1 ) for liquids increases with (A) Increasing temperature (B) Decreasing temperature (C) Decreasing Reynolds number (D) None of these

Last Answer : (A) Increasing temperature

The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Description : The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Last Answer : (A) Increasing temperature of the vapour

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Last Answer : Option B

Seasoning of timber is done for (A) Increasing moisture content (B) Decreasing moisture content (C) Increasing strength of timber (D) None to these

Description : Seasoning of timber is done for (A) Increasing moisture content (B) Decreasing moisture content (C) Increasing strength of timber (D) None to these

Last Answer : Answer: Option B

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Description : Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Last Answer : (A) Fluidity

Work hardening of a material (A) Decreases its tensile strength (B) Decreases its ductility (C) Increases its ductility (D) Does not affect its ductility

Description : Work hardening of a material (A) Decreases its tensile strength (B) Decreases its ductility (C) Increases its ductility (D) Does not affect its ductility

Last Answer : (B) Decreases its ductility

Addition of __________ in steel can help in increasing the depth of hardness. (A) Nickel (B) Chromium (C) Vanadium (D) Tungsten

Description : Addition of __________ in steel can help in increasing the depth of hardness. (A) Nickel (B) Chromium (C) Vanadium (D) Tungsten

Last Answer : (D) Tungsten